[PATCH 1/3] ARM: dts: imx7d: create i.MX 7Solo base device tree
Stefan Agner
stefan at agner.ch
Tue Jun 7 19:37:07 PDT 2016
The i.MX 7 series currently consists of two SoCs: i.MX 7Solo and
7Dual. The i.MX 7Solo implements a subset of features available on
i.MX 7Dual, hence create imx7s.dtsi as the base device tree. The
i.MX 7Dual's additional features over i.MX 7Solo are:
- Second Cortex-A7 core
- Second Gigabit Ethernet controller
- EPD (Electronc Paper Display, not yet part of the device tree)
- PCIe (not yet part of the device tree)
- Additional USB2.0 OTG controller
Signed-off-by: Stefan Agner <stefan at agner.ch>
---
arch/arm/boot/dts/imx7d.dtsi | 923 +++----------------------------------------
arch/arm/boot/dts/imx7s.dtsi | 880 +++++++++++++++++++++++++++++++++++++++++
2 files changed, 928 insertions(+), 875 deletions(-)
create mode 100644 arch/arm/boot/dts/imx7s.dtsi
diff --git a/arch/arm/boot/dts/imx7d.dtsi b/arch/arm/boot/dts/imx7d.dtsi
index 6b3faa2..51c13cb 100644
--- a/arch/arm/boot/dts/imx7d.dtsi
+++ b/arch/arm/boot/dts/imx7d.dtsi
@@ -1,5 +1,6 @@
/*
* Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2016 Toradex AG
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
@@ -40,54 +41,10 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/clock/imx7d-clock.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include "imx7d-pinfunc.h"
-#include "skeleton.dtsi"
+#include "imx7s.dtsi"
/ {
- aliases {
- gpio0 = &gpio1;
- gpio1 = &gpio2;
- gpio2 = &gpio3;
- gpio3 = &gpio4;
- gpio4 = &gpio5;
- gpio5 = &gpio6;
- gpio6 = &gpio7;
- i2c0 = &i2c1;
- i2c1 = &i2c2;
- i2c2 = &i2c3;
- i2c3 = &i2c4;
- mmc0 = &usdhc1;
- mmc1 = &usdhc2;
- mmc2 = &usdhc3;
- serial0 = &uart1;
- serial1 = &uart2;
- serial2 = &uart3;
- serial3 = &uart4;
- serial4 = &uart5;
- serial5 = &uart6;
- serial6 = &uart7;
- };
-
cpus {
- #address-cells = <1>;
- #size-cells = <0>;
-
- cpu0: cpu at 0 {
- compatible = "arm,cortex-a7";
- device_type = "cpu";
- reg = <0>;
- operating-points = <
- /* KHz uV */
- 996000 1075000
- 792000 975000
- >;
- clock-latency = <61036>; /* two CLK32 periods */
- clocks = <&clks IMX7D_CLK_ARM>;
- };
-
cpu1: cpu at 1 {
compatible = "arm,cortex-a7";
device_type = "cpu";
@@ -95,221 +52,6 @@
};
};
- intc: interrupt-controller at 31001000 {
- compatible = "arm,cortex-a7-gic";
- #interrupt-cells = <3>;
- interrupt-controller;
- reg = <0x31001000 0x1000>,
- <0x31002000 0x1000>,
- <0x31004000 0x2000>,
- <0x31006000 0x2000>;
- };
-
- ckil: clock-cki {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <32768>;
- clock-output-names = "ckil";
- };
-
- osc: clock-osc {
- compatible = "fixed-clock";
- #clock-cells = <0>;
- clock-frequency = <24000000>;
- clock-output-names = "osc";
- };
-
- timer {
- compatible = "arm,armv7-timer";
- interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
- <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
- interrupt-parent = <&intc>;
- };
-
- etr at 30086000 {
- compatible = "arm,coresight-tmc", "arm,primecell";
- reg = <0x30086000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- port {
- etr_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&replicator_out_port1>;
- };
- };
- };
-
- tpiu at 30087000 {
- compatible = "arm,coresight-tpiu", "arm,primecell";
- reg = <0x30087000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- port {
- tpiu_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&replicator_out_port1>;
- };
- };
- };
-
- replicator {
- /*
- * non-configurable replicators don't show up on the
- * AMBA bus. As such no need to add "arm,primecell"
- */
- compatible = "arm,coresight-replicator";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* replicator output ports */
- port at 0 {
- reg = <0>;
- replicator_out_port0: endpoint {
- remote-endpoint = <&tpiu_in_port>;
- };
- };
-
- port at 1 {
- reg = <1>;
- replicator_out_port1: endpoint {
- remote-endpoint = <&etr_in_port>;
- };
- };
-
- /* replicator input port */
- port at 2 {
- reg = <0>;
- replicator_in_port0: endpoint {
- slave-mode;
- remote-endpoint = <&etf_out_port>;
- };
- };
- };
- };
-
- etf at 30084000 {
- compatible = "arm,coresight-tmc", "arm,primecell";
- reg = <0x30084000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- port at 0 {
- reg = <0>;
- etf_in_port: endpoint {
- slave-mode;
- remote-endpoint = <&hugo_funnel_out_port0>;
- };
- };
-
- port at 1 {
- reg = <0>;
- etf_out_port: endpoint {
- remote-endpoint = <&replicator_in_port0>;
- };
- };
- };
- };
-
- funnel at 30083000 {
- compatible = "arm,coresight-funnel", "arm,primecell";
- reg = <0x30083000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* funnel input ports */
- port at 0 {
- reg = <0>;
- hugo_funnel_in_port0: endpoint {
- slave-mode;
- remote-endpoint = <&ca_funnel_out_port0>;
- };
- };
-
- port at 1 {
- reg = <1>;
- hugo_funnel_in_port1: endpoint {
- slave-mode; /* M4 input */
- };
- };
-
- port at 2 {
- reg = <0>;
- hugo_funnel_out_port0: endpoint {
- remote-endpoint = <&etf_in_port>;
- };
- };
-
- /* the other input ports are not connect to anything */
- };
- };
-
- funnel at 30041000 {
- compatible = "arm,coresight-funnel", "arm,primecell";
- reg = <0x30041000 0x1000>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
-
- /* funnel input ports */
- port at 0 {
- reg = <0>;
- ca_funnel_in_port0: endpoint {
- slave-mode;
- remote-endpoint = <&etm0_out_port>;
- };
- };
-
- port at 1 {
- reg = <1>;
- ca_funnel_in_port1: endpoint {
- slave-mode;
- remote-endpoint = <&etm1_out_port>;
- };
- };
-
- /* funnel output port */
- port at 2 {
- reg = <0>;
- ca_funnel_out_port0: endpoint {
- remote-endpoint = <&hugo_funnel_in_port0>;
- };
- };
-
- /* the other input ports are not connect to anything */
- };
- };
-
- etm at 3007c000 {
- compatible = "arm,coresight-etm3x", "arm,primecell";
- reg = <0x3007c000 0x1000>;
- cpu = <&cpu0>;
- clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
- clock-names = "apb_pclk";
-
- port {
- etm0_out_port: endpoint {
- remote-endpoint = <&ca_funnel_in_port0>;
- };
- };
- };
-
etm at 3007d000 {
compatible = "arm,coresight-etm3x", "arm,primecell";
reg = <0x3007d000 0x1000>;
@@ -330,626 +72,57 @@
};
};
};
+};
- soc {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "simple-bus";
- interrupt-parent = <&intc>;
- ranges;
-
- aips1: aips-bus at 30000000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30000000 0x400000>;
- ranges;
-
- gpio1: gpio at 30200000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30200000 0x10000>;
- interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* GPIO1_INT15_0 */
- <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; /* GPIO1_INT31_16 */
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio2: gpio at 30210000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30210000 0x10000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio3: gpio at 30220000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30220000 0x10000>;
- interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio4: gpio at 30230000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30230000 0x10000>;
- interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio5: gpio at 30240000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30240000 0x10000>;
- interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio6: gpio at 30250000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30250000 0x10000>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- gpio7: gpio at 30260000 {
- compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
- reg = <0x30260000 0x10000>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- gpio-controller;
- #gpio-cells = <2>;
- interrupt-controller;
- #interrupt-cells = <2>;
- };
-
- wdog1: wdog at 30280000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x30280000 0x10000>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG1_ROOT_CLK>;
- };
-
- wdog2: wdog at 30290000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x30290000 0x10000>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG2_ROOT_CLK>;
- status = "disabled";
- };
-
- wdog3: wdog at 302a0000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x302a0000 0x10000>;
- interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG3_ROOT_CLK>;
- status = "disabled";
- };
-
- wdog4: wdog at 302b0000 {
- compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
- reg = <0x302b0000 0x10000>;
- interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_WDOG4_ROOT_CLK>;
- status = "disabled";
- };
-
- iomuxc_lpsr: iomuxc-lpsr at 302c0000 {
- compatible = "fsl,imx7d-iomuxc-lpsr";
- reg = <0x302c0000 0x10000>;
- fsl,input-sel = <&iomuxc>;
- };
-
- gpt1: gpt at 302d0000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x302d0000 0x10000>;
- interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT1_ROOT_CLK>;
- clock-names = "ipg", "per";
- };
-
- gpt2: gpt at 302e0000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x302e0000 0x10000>;
- interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT2_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- gpt3: gpt at 302f0000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x302f0000 0x10000>;
- interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT3_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- gpt4: gpt at 30300000 {
- compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
- reg = <0x30300000 0x10000>;
- interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_GPT4_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- iomuxc: iomuxc at 30330000 {
- compatible = "fsl,imx7d-iomuxc";
- reg = <0x30330000 0x10000>;
- };
-
- gpr: iomuxc-gpr at 30340000 {
- compatible = "fsl,imx7d-iomuxc-gpr", "syscon";
- reg = <0x30340000 0x10000>;
- };
-
- ocotp: ocotp-ctrl at 30350000 {
- compatible = "syscon";
- reg = <0x30350000 0x10000>;
- clocks = <&clks IMX7D_CLK_DUMMY>;
- status = "disabled";
- };
-
- anatop: anatop at 30360000 {
- compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop",
- "syscon", "simple-bus";
- reg = <0x30360000 0x10000>;
- interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
-
- reg_1p0d: regulator-vdd1p0d at 210 {
- compatible = "fsl,anatop-regulator";
- regulator-name = "vdd1p0d";
- regulator-min-microvolt = <800000>;
- regulator-max-microvolt = <1200000>;
- anatop-reg-offset = <0x210>;
- anatop-vol-bit-shift = <8>;
- anatop-vol-bit-width = <5>;
- anatop-min-bit-val = <8>;
- anatop-min-voltage = <800000>;
- anatop-max-voltage = <1200000>;
- anatop-enable-bit = <31>;
- };
- };
-
- snvs: snvs at 30370000 {
- compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
- reg = <0x30370000 0x10000>;
-
- snvs_rtc: snvs-rtc-lp {
- compatible = "fsl,sec-v4.0-mon-rtc-lp";
- regmap = <&snvs>;
- offset = <0x34>;
- interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- snvs_poweroff: snvs-poweroff {
- compatible = "syscon-poweroff";
- regmap = <&snvs>;
- offset = <0x38>;
- mask = <0x60>;
- };
-
- snvs_pwrkey: snvs-powerkey {
- compatible = "fsl,sec-v4.0-pwrkey";
- regmap = <&snvs>;
- interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
- linux,keycode = <KEY_POWER>;
- wakeup-source;
- };
- };
-
- clks: ccm at 30380000 {
- compatible = "fsl,imx7d-ccm";
- reg = <0x30380000 0x10000>;
- interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
- #clock-cells = <1>;
- clocks = <&ckil>, <&osc>;
- clock-names = "ckil", "osc";
- };
-
- src: src at 30390000 {
- compatible = "fsl,imx7d-src", "fsl,imx51-src", "syscon";
- reg = <0x30390000 0x10000>;
- interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
- #reset-cells = <1>;
- };
- };
-
- aips2: aips-bus at 30400000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30400000 0x400000>;
- ranges;
-
- adc1: adc at 30610000 {
- compatible = "fsl,imx7d-adc";
- reg = <0x30610000 0x10000>;
- interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ADC_ROOT_CLK>;
- clock-names = "adc";
- status = "disabled";
- };
-
- adc2: adc at 30620000 {
- compatible = "fsl,imx7d-adc";
- reg = <0x30620000 0x10000>;
- interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ADC_ROOT_CLK>;
- clock-names = "adc";
- status = "disabled";
- };
-
- pwm1: pwm at 30660000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30660000 0x10000>;
- interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM1_ROOT_CLK>,
- <&clks IMX7D_PWM1_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm2: pwm at 30670000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30670000 0x10000>;
- interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM2_ROOT_CLK>,
- <&clks IMX7D_PWM2_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm3: pwm at 30680000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30680000 0x10000>;
- interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM3_ROOT_CLK>,
- <&clks IMX7D_PWM3_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- pwm4: pwm at 30690000 {
- compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
- reg = <0x30690000 0x10000>;
- interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_PWM4_ROOT_CLK>,
- <&clks IMX7D_PWM4_ROOT_CLK>;
- clock-names = "ipg", "per";
- #pwm-cells = <2>;
- status = "disabled";
- };
-
- lcdif: lcdif at 30730000 {
- compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
- reg = <0x30730000 0x10000>;
- interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>;
- clock-names = "pix", "axi", "disp_axi";
- status = "disabled";
- };
- };
-
- aips3: aips-bus at 30800000 {
- compatible = "fsl,aips-bus", "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- reg = <0x30800000 0x400000>;
- ranges;
-
- uart1: serial at 30860000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30860000 0x10000>;
- interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART1_ROOT_CLK>,
- <&clks IMX7D_UART1_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart2: serial at 30890000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30890000 0x10000>;
- interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART2_ROOT_CLK>,
- <&clks IMX7D_UART2_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart3: serial at 30880000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30880000 0x10000>;
- interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART3_ROOT_CLK>,
- <&clks IMX7D_UART3_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- flexcan1: can at 30a00000 {
- compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
- reg = <0x30a00000 0x10000>;
- interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CAN1_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- flexcan2: can at 30a10000 {
- compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
- reg = <0x30a10000 0x10000>;
- interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CAN2_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- i2c1: i2c at 30a20000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a20000 0x10000>;
- interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C1_ROOT_CLK>;
- status = "disabled";
- };
-
- i2c2: i2c at 30a30000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a30000 0x10000>;
- interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C2_ROOT_CLK>;
- status = "disabled";
- };
-
- i2c3: i2c at 30a40000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a40000 0x10000>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C3_ROOT_CLK>;
- status = "disabled";
- };
-
- i2c4: i2c at 30a50000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
- reg = <0x30a50000 0x10000>;
- interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_I2C4_ROOT_CLK>;
- status = "disabled";
- };
-
- uart4: serial at 30a60000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a60000 0x10000>;
- interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART4_ROOT_CLK>,
- <&clks IMX7D_UART4_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart5: serial at 30a70000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a70000 0x10000>;
- interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART5_ROOT_CLK>,
- <&clks IMX7D_UART5_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart6: serial at 30a80000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a80000 0x10000>;
- interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART6_ROOT_CLK>,
- <&clks IMX7D_UART6_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- uart7: serial at 30a90000 {
- compatible = "fsl,imx7d-uart",
- "fsl,imx6q-uart";
- reg = <0x30a90000 0x10000>;
- interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_UART7_ROOT_CLK>,
- <&clks IMX7D_UART7_ROOT_CLK>;
- clock-names = "ipg", "per";
- status = "disabled";
- };
-
- usbotg1: usb at 30b10000 {
- compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
- reg = <0x30b10000 0x200>;
- interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_USB_CTRL_CLK>;
- fsl,usbphy = <&usbphynop1>;
- fsl,usbmisc = <&usbmisc1 0>;
- phy-clkgate-delay-us = <400>;
- status = "disabled";
- };
-
- usbotg2: usb at 30b20000 {
- compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
- reg = <0x30b20000 0x200>;
- interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_USB_CTRL_CLK>;
- fsl,usbphy = <&usbphynop2>;
- fsl,usbmisc = <&usbmisc2 0>;
- phy-clkgate-delay-us = <400>;
- status = "disabled";
- };
-
- usbh: usb at 30b30000 {
- compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
- reg = <0x30b30000 0x200>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_USB_CTRL_CLK>;
- fsl,usbphy = <&usbphynop3>;
- fsl,usbmisc = <&usbmisc3 0>;
- phy_type = "hsic";
- dr_mode = "host";
- phy-clkgate-delay-us = <400>;
- status = "disabled";
- };
-
- usbmisc1: usbmisc at 30b10200 {
- #index-cells = <1>;
- compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x30b10200 0x200>;
- };
-
- usbmisc2: usbmisc at 30b20200 {
- #index-cells = <1>;
- compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x30b20200 0x200>;
- };
-
- usbmisc3: usbmisc at 30b30200 {
- #index-cells = <1>;
- compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
- reg = <0x30b30200 0x200>;
- };
-
- usbphynop1: usbphynop1 {
- compatible = "usb-nop-xceiv";
- clocks = <&clks IMX7D_USB_PHY1_CLK>;
- clock-names = "main_clk";
- };
-
- usbphynop2: usbphynop2 {
- compatible = "usb-nop-xceiv";
- clocks = <&clks IMX7D_USB_PHY2_CLK>;
- clock-names = "main_clk";
- };
-
- usbphynop3: usbphynop3 {
- compatible = "usb-nop-xceiv";
- clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
- clock-names = "main_clk";
- };
-
- usdhc1: usdhc at 30b40000 {
- compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
- reg = <0x30b40000 0x10000>;
- interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_USDHC1_ROOT_CLK>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
+&aips3 {
+ usbotg2: usb at 30b20000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b20000 0x200>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop2>;
+ fsl,usbmisc = <&usbmisc2 0>;
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
- usdhc2: usdhc at 30b50000 {
- compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
- reg = <0x30b50000 0x10000>;
- interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_USDHC2_ROOT_CLK>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
+ usbmisc2: usbmisc at 30b20200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b20200 0x200>;
+ };
- usdhc3: usdhc at 30b60000 {
- compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
- reg = <0x30b60000 0x10000>;
- interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_CLK_DUMMY>,
- <&clks IMX7D_USDHC3_ROOT_CLK>;
- clock-names = "ipg", "ahb", "per";
- bus-width = <4>;
- status = "disabled";
- };
+ usbphynop2: usbphynop2 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_PHY2_CLK>;
+ clock-names = "main_clk";
+ };
- fec1: ethernet at 30be0000 {
- compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
- reg = <0x30be0000 0x10000>;
- interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
- <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
- <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
- clock-names = "ipg", "ahb", "ptp",
- "enet_clk_ref", "enet_out";
- fsl,num-tx-queues=<3>;
- fsl,num-rx-queues=<3>;
- status = "disabled";
- };
+ fec2: ethernet at 30bf0000 {
+ compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+ reg = <0x30bf0000 0x10000>;
+ interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET2_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+ <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<3>;
+ fsl,num-rx-queues=<3>;
+ status = "disabled";
+ };
+};
- fec2: ethernet at 30bf0000 {
- compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
- reg = <0x30bf0000 0x10000>;
- interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET_AXI_ROOT_CLK>,
- <&clks IMX7D_ENET2_TIME_ROOT_CLK>,
- <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
- <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
- clock-names = "ipg", "ahb", "ptp",
- "enet_clk_ref", "enet_out";
- fsl,num-tx-queues=<3>;
- fsl,num-rx-queues=<3>;
- status = "disabled";
- };
+&ca_funnel_ports {
+ port at 1 {
+ reg = <1>;
+ ca_funnel_in_port1: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm1_out_port>;
};
};
};
diff --git a/arch/arm/boot/dts/imx7s.dtsi b/arch/arm/boot/dts/imx7s.dtsi
new file mode 100644
index 0000000..a5fd2d7
--- /dev/null
+++ b/arch/arm/boot/dts/imx7s.dtsi
@@ -0,0 +1,880 @@
+/*
+ * Copyright 2015 Freescale Semiconductor, Inc.
+ * Copyright 2016 Toradex AG
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/imx7d-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include "imx7d-pinfunc.h"
+#include "skeleton.dtsi"
+
+/ {
+ aliases {
+ gpio0 = &gpio1;
+ gpio1 = &gpio2;
+ gpio2 = &gpio3;
+ gpio3 = &gpio4;
+ gpio4 = &gpio5;
+ gpio5 = &gpio6;
+ gpio6 = &gpio7;
+ i2c0 = &i2c1;
+ i2c1 = &i2c2;
+ i2c2 = &i2c3;
+ i2c3 = &i2c4;
+ mmc0 = &usdhc1;
+ mmc1 = &usdhc2;
+ mmc2 = &usdhc3;
+ serial0 = &uart1;
+ serial1 = &uart2;
+ serial2 = &uart3;
+ serial3 = &uart4;
+ serial4 = &uart5;
+ serial5 = &uart6;
+ serial6 = &uart7;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ operating-points = <
+ /* KHz uV */
+ 996000 1075000
+ 792000 975000
+ >;
+ clock-latency = <61036>; /* two CLK32 periods */
+ clocks = <&clks IMX7D_CLK_ARM>;
+ };
+ };
+
+ intc: interrupt-controller at 31001000 {
+ compatible = "arm,cortex-a7-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0x31001000 0x1000>,
+ <0x31002000 0x1000>,
+ <0x31004000 0x2000>,
+ <0x31006000 0x2000>;
+ };
+
+ ckil: clock-cki {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <32768>;
+ clock-output-names = "ckil";
+ };
+
+ osc: clock-osc {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <24000000>;
+ clock-output-names = "osc";
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ interrupt-parent = <&intc>;
+ };
+
+ etr at 30086000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x30086000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ port {
+ etr_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port1>;
+ };
+ };
+ };
+
+ tpiu at 30087000 {
+ compatible = "arm,coresight-tpiu", "arm,primecell";
+ reg = <0x30087000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ port {
+ tpiu_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&replicator_out_port1>;
+ };
+ };
+ };
+
+ replicator {
+ /*
+ * non-configurable replicators don't show up on the
+ * AMBA bus. As such no need to add "arm,primecell"
+ */
+ compatible = "arm,coresight-replicator";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* replicator output ports */
+ port at 0 {
+ reg = <0>;
+ replicator_out_port0: endpoint {
+ remote-endpoint = <&tpiu_in_port>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ replicator_out_port1: endpoint {
+ remote-endpoint = <&etr_in_port>;
+ };
+ };
+
+ /* replicator input port */
+ port at 2 {
+ reg = <0>;
+ replicator_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etf_out_port>;
+ };
+ };
+ };
+ };
+
+ etf at 30084000 {
+ compatible = "arm,coresight-tmc", "arm,primecell";
+ reg = <0x30084000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ etf_in_port: endpoint {
+ slave-mode;
+ remote-endpoint = <&hugo_funnel_out_port0>;
+ };
+ };
+
+ port at 1 {
+ reg = <0>;
+ etf_out_port: endpoint {
+ remote-endpoint = <&replicator_in_port0>;
+ };
+ };
+ };
+ };
+
+ funnel at 30083000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0x30083000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* funnel input ports */
+ port at 0 {
+ reg = <0>;
+ hugo_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&ca_funnel_out_port0>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ hugo_funnel_in_port1: endpoint {
+ slave-mode; /* M4 input */
+ };
+ };
+
+ port at 2 {
+ reg = <0>;
+ hugo_funnel_out_port0: endpoint {
+ remote-endpoint = <&etf_in_port>;
+ };
+ };
+
+ /* the other input ports are not connect to anything */
+ };
+ };
+
+ funnel at 30041000 {
+ compatible = "arm,coresight-funnel", "arm,primecell";
+ reg = <0x30041000 0x1000>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ ca_funnel_ports: ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* funnel input ports */
+ port at 0 {
+ reg = <0>;
+ ca_funnel_in_port0: endpoint {
+ slave-mode;
+ remote-endpoint = <&etm0_out_port>;
+ };
+ };
+
+ /* funnel output port */
+ port at 2 {
+ reg = <0>;
+ ca_funnel_out_port0: endpoint {
+ remote-endpoint = <&hugo_funnel_in_port0>;
+ };
+ };
+
+ /* the other input ports are not connect to anything */
+ };
+ };
+
+ etm at 3007c000 {
+ compatible = "arm,coresight-etm3x", "arm,primecell";
+ reg = <0x3007c000 0x1000>;
+ cpu = <&cpu0>;
+ clocks = <&clks IMX7D_MAIN_AXI_ROOT_CLK>;
+ clock-names = "apb_pclk";
+
+ port {
+ etm0_out_port: endpoint {
+ remote-endpoint = <&ca_funnel_in_port0>;
+ };
+ };
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ aips1: aips-bus at 30000000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30000000 0x400000>;
+ ranges;
+
+ gpio1: gpio at 30200000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30200000 0x10000>;
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>, /* GPIO1_INT15_0 */
+ <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; /* GPIO1_INT31_16 */
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio2: gpio at 30210000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30210000 0x10000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio3: gpio at 30220000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30220000 0x10000>;
+ interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio4: gpio at 30230000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30230000 0x10000>;
+ interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio5: gpio at 30240000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30240000 0x10000>;
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio6: gpio at 30250000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30250000 0x10000>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ gpio7: gpio at 30260000 {
+ compatible = "fsl,imx7d-gpio", "fsl,imx35-gpio";
+ reg = <0x30260000 0x10000>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ wdog1: wdog at 30280000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x30280000 0x10000>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG1_ROOT_CLK>;
+ };
+
+ wdog2: wdog at 30290000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x30290000 0x10000>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG2_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ wdog3: wdog at 302a0000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x302a0000 0x10000>;
+ interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG3_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ wdog4: wdog at 302b0000 {
+ compatible = "fsl,imx7d-wdt", "fsl,imx21-wdt";
+ reg = <0x302b0000 0x10000>;
+ interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_WDOG4_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ iomuxc_lpsr: iomuxc-lpsr at 302c0000 {
+ compatible = "fsl,imx7d-iomuxc-lpsr";
+ reg = <0x302c0000 0x10000>;
+ fsl,input-sel = <&iomuxc>;
+ };
+
+ gpt1: gpt at 302d0000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x302d0000 0x10000>;
+ interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ };
+
+ gpt2: gpt at 302e0000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x302e0000 0x10000>;
+ interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt3: gpt at 302f0000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x302f0000 0x10000>;
+ interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ gpt4: gpt at 30300000 {
+ compatible = "fsl,imx7d-gpt", "fsl,imx6sx-gpt";
+ reg = <0x30300000 0x10000>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_GPT4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ iomuxc: iomuxc at 30330000 {
+ compatible = "fsl,imx7d-iomuxc";
+ reg = <0x30330000 0x10000>;
+ };
+
+ gpr: iomuxc-gpr at 30340000 {
+ compatible = "fsl,imx7d-iomuxc-gpr", "syscon";
+ reg = <0x30340000 0x10000>;
+ };
+
+ ocotp: ocotp-ctrl at 30350000 {
+ compatible = "syscon";
+ reg = <0x30350000 0x10000>;
+ clocks = <&clks IMX7D_CLK_DUMMY>;
+ status = "disabled";
+ };
+
+ anatop: anatop at 30360000 {
+ compatible = "fsl,imx7d-anatop", "fsl,imx6q-anatop",
+ "syscon", "simple-bus";
+ reg = <0x30360000 0x10000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+
+ reg_1p0d: regulator-vdd1p0d at 210 {
+ compatible = "fsl,anatop-regulator";
+ regulator-name = "vdd1p0d";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1200000>;
+ anatop-reg-offset = <0x210>;
+ anatop-vol-bit-shift = <8>;
+ anatop-vol-bit-width = <5>;
+ anatop-min-bit-val = <8>;
+ anatop-min-voltage = <800000>;
+ anatop-max-voltage = <1200000>;
+ anatop-enable-bit = <31>;
+ };
+ };
+
+ snvs: snvs at 30370000 {
+ compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
+ reg = <0x30370000 0x10000>;
+
+ snvs_rtc: snvs-rtc-lp {
+ compatible = "fsl,sec-v4.0-mon-rtc-lp";
+ regmap = <&snvs>;
+ offset = <0x34>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ snvs_poweroff: snvs-poweroff {
+ compatible = "syscon-poweroff";
+ regmap = <&snvs>;
+ offset = <0x38>;
+ mask = <0x60>;
+ };
+
+ snvs_pwrkey: snvs-powerkey {
+ compatible = "fsl,sec-v4.0-pwrkey";
+ regmap = <&snvs>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ linux,keycode = <KEY_POWER>;
+ wakeup-source;
+ };
+ };
+
+ clks: ccm at 30380000 {
+ compatible = "fsl,imx7d-ccm";
+ reg = <0x30380000 0x10000>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+ #clock-cells = <1>;
+ clocks = <&ckil>, <&osc>;
+ clock-names = "ckil", "osc";
+ };
+
+ src: src at 30390000 {
+ compatible = "fsl,imx7d-src", "fsl,imx51-src", "syscon";
+ reg = <0x30390000 0x10000>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ #reset-cells = <1>;
+ };
+ };
+
+ aips2: aips-bus at 30400000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30400000 0x400000>;
+ ranges;
+
+ adc1: adc at 30610000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30610000 0x10000>;
+ interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ adc2: adc at 30620000 {
+ compatible = "fsl,imx7d-adc";
+ reg = <0x30620000 0x10000>;
+ interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ADC_ROOT_CLK>;
+ clock-names = "adc";
+ status = "disabled";
+ };
+
+ pwm1: pwm at 30660000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30660000 0x10000>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM1_ROOT_CLK>,
+ <&clks IMX7D_PWM1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm2: pwm at 30670000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30670000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM2_ROOT_CLK>,
+ <&clks IMX7D_PWM2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm at 30680000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30680000 0x10000>;
+ interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM3_ROOT_CLK>,
+ <&clks IMX7D_PWM3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ pwm4: pwm at 30690000 {
+ compatible = "fsl,imx7d-pwm", "fsl,imx27-pwm";
+ reg = <0x30690000 0x10000>;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_PWM4_ROOT_CLK>,
+ <&clks IMX7D_PWM4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ #pwm-cells = <2>;
+ status = "disabled";
+ };
+
+ lcdif: lcdif at 30730000 {
+ compatible = "fsl,imx7d-lcdif", "fsl,imx28-lcdif";
+ reg = <0x30730000 0x10000>;
+ interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_LCDIF_PIXEL_ROOT_CLK>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>;
+ clock-names = "pix", "axi", "disp_axi";
+ status = "disabled";
+ };
+ };
+
+ aips3: aips-bus at 30800000 {
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x30800000 0x400000>;
+ ranges;
+
+ uart1: serial at 30860000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30860000 0x10000>;
+ interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART1_ROOT_CLK>,
+ <&clks IMX7D_UART1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart2: serial at 30890000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30890000 0x10000>;
+ interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART2_ROOT_CLK>,
+ <&clks IMX7D_UART2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart3: serial at 30880000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30880000 0x10000>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART3_ROOT_CLK>,
+ <&clks IMX7D_UART3_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ flexcan1: can at 30a00000 {
+ compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x30a00000 0x10000>;
+ interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CAN1_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ flexcan2: can at 30a10000 {
+ compatible = "fsl,imx7d-flexcan", "fsl,imx6q-flexcan";
+ reg = <0x30a10000 0x10000>;
+ interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CAN2_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ i2c1: i2c at 30a20000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a20000 0x10000>;
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C1_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at 30a30000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a30000 0x10000>;
+ interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C2_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at 30a40000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a40000 0x10000>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C3_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ i2c4: i2c at 30a50000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx7d-i2c", "fsl,imx21-i2c";
+ reg = <0x30a50000 0x10000>;
+ interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_I2C4_ROOT_CLK>;
+ status = "disabled";
+ };
+
+ uart4: serial at 30a60000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a60000 0x10000>;
+ interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART4_ROOT_CLK>,
+ <&clks IMX7D_UART4_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart5: serial at 30a70000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a70000 0x10000>;
+ interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART5_ROOT_CLK>,
+ <&clks IMX7D_UART5_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart6: serial at 30a80000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a80000 0x10000>;
+ interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART6_ROOT_CLK>,
+ <&clks IMX7D_UART6_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ uart7: serial at 30a90000 {
+ compatible = "fsl,imx7d-uart",
+ "fsl,imx6q-uart";
+ reg = <0x30a90000 0x10000>;
+ interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_UART7_ROOT_CLK>,
+ <&clks IMX7D_UART7_ROOT_CLK>;
+ clock-names = "ipg", "per";
+ status = "disabled";
+ };
+
+ usbotg1: usb at 30b10000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b10000 0x200>;
+ interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop1>;
+ fsl,usbmisc = <&usbmisc1 0>;
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbh: usb at 30b30000 {
+ compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
+ reg = <0x30b30000 0x200>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_USB_CTRL_CLK>;
+ fsl,usbphy = <&usbphynop3>;
+ fsl,usbmisc = <&usbmisc3 0>;
+ phy_type = "hsic";
+ dr_mode = "host";
+ phy-clkgate-delay-us = <400>;
+ status = "disabled";
+ };
+
+ usbmisc1: usbmisc at 30b10200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b10200 0x200>;
+ };
+
+ usbmisc3: usbmisc at 30b30200 {
+ #index-cells = <1>;
+ compatible = "fsl,imx7d-usbmisc", "fsl,imx6q-usbmisc";
+ reg = <0x30b30200 0x200>;
+ };
+
+ usbphynop1: usbphynop1 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_PHY1_CLK>;
+ clock-names = "main_clk";
+ };
+
+ usbphynop3: usbphynop3 {
+ compatible = "usb-nop-xceiv";
+ clocks = <&clks IMX7D_USB_HSIC_ROOT_CLK>;
+ clock-names = "main_clk";
+ };
+
+ usdhc1: usdhc at 30b40000 {
+ compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x30b40000 0x10000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_USDHC1_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc2: usdhc at 30b50000 {
+ compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x30b50000 0x10000>;
+ interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_USDHC2_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ usdhc3: usdhc at 30b60000 {
+ compatible = "fsl,imx7d-usdhc", "fsl,imx6sl-usdhc";
+ reg = <0x30b60000 0x10000>;
+ interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_CLK_DUMMY>,
+ <&clks IMX7D_USDHC3_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "per";
+ bus-width = <4>;
+ status = "disabled";
+ };
+
+ fec1: ethernet at 30be0000 {
+ compatible = "fsl,imx7d-fec", "fsl,imx6sx-fec";
+ reg = <0x30be0000 0x10000>;
+ interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET_AXI_ROOT_CLK>,
+ <&clks IMX7D_ENET1_TIME_ROOT_CLK>,
+ <&clks IMX7D_PLL_ENET_MAIN_125M_CLK>,
+ <&clks IMX7D_ENET_PHY_REF_ROOT_CLK>;
+ clock-names = "ipg", "ahb", "ptp",
+ "enet_clk_ref", "enet_out";
+ fsl,num-tx-queues=<3>;
+ fsl,num-rx-queues=<3>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
2.8.3
More information about the linux-arm-kernel
mailing list