[PATCH 2/5] mfd: add Ricoh RN5T567 PMIC support

Stefan Agner stefan at agner.ch
Sat Jun 4 17:17:45 PDT 2016


The Ricoh RN5T567 is from the same family as the Ricoh RN5T618 is,
the differences are:

+ DCDC4
+ Slightly different output voltage/currents
+ 32kHz Output
- ADC/Charger capabilities

Signed-off-by: Stefan Agner <stefan at agner.ch>
---
 Documentation/devicetree/bindings/mfd/rn5t618.txt | 19 ++++++++++-------
 drivers/mfd/Kconfig                               |  7 +++---
 drivers/mfd/rn5t618.c                             | 26 +++++++++++++++++------
 include/linux/mfd/rn5t618.h                       | 12 +++++++++++
 4 files changed, 46 insertions(+), 18 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/rn5t618.txt b/Documentation/devicetree/bindings/mfd/rn5t618.txt
index 937785a..5b493ed 100644
--- a/Documentation/devicetree/bindings/mfd/rn5t618.txt
+++ b/Documentation/devicetree/bindings/mfd/rn5t618.txt
@@ -1,18 +1,21 @@
-* Ricoh RN5T618 PMIC
+* Ricoh RN5T567/RN5T618 PMIC
 
-Ricoh RN5T618 is a power management IC which integrates 3 step-down
-DCDC converters, 7 low-dropout regulators, a Li-ion battery charger,
-fuel gauge, ADC, GPIOs and a watchdog timer. It can be controlled
-through a I2C interface.
+Ricoh RN5T567/RN5T618 is a power management IC family which integrates
+3 to 5 step-down DCDC converters, 7 low-dropout regulators, GPIOs and
+a watchdog timer. The RN5T618 provides additionally a Li-ion battery
+charger, fuel gauge and an ADC. It can be controlled through a I2C
+interface.
 
 Required properties:
- - compatible: should be "ricoh,rn5t618"
+ - compatible: must be one of
+		"ricoh,rn5t567"
+		"ricoh,rn5t618"
  - reg: the I2C slave address of the device
 
 Sub-nodes:
  - regulators: the node is required if the regulator functionality is
-   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, LDO1,
-   LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
+   needed. The valid regulator names are: DCDC1, DCDC2, DCDC3, DCDC4
+   (RN5T567), LDO1, LDO2, LDO3, LDO4, LDO5, LDORTC1 and LDORTC2.
    The common bindings for each individual regulator can be found in:
    Documentation/devicetree/bindings/regulator/regulator.txt
 
diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
index 1bcf601..ff031a7 100644
--- a/drivers/mfd/Kconfig
+++ b/drivers/mfd/Kconfig
@@ -852,13 +852,14 @@ config MFD_RK808
 	  including interrupts, RTC, LDO & DCDC regulators, and onkey.
 
 config MFD_RN5T618
-	tristate "Ricoh RN5T5618 PMIC"
+	tristate "Ricoh RN5T567/618 PMIC"
 	depends on I2C
+	depends on OF
 	select MFD_CORE
 	select REGMAP_I2C
 	help
-	  Say yes here to add support for the Ricoh RN5T618 PMIC. This
-	  driver provides common support for accessing the device,
+	  Say yes here to add support for the Ricoh RN5T567 or R5T618 PMIC.
+	  This driver provides common support for accessing the device,
 	  additional drivers must be enabled in order to use the
 	  functionality of the device.
 
diff --git a/drivers/mfd/rn5t618.c b/drivers/mfd/rn5t618.c
index 0ad51d7..7607ced 100644
--- a/drivers/mfd/rn5t618.c
+++ b/drivers/mfd/rn5t618.c
@@ -2,6 +2,7 @@
  * MFD core driver for Ricoh RN5T618 PMIC
  *
  * Copyright (C) 2014 Beniamino Galvani <b.galvani at gmail.com>
+ * Copyright (C) 2016 Toradex AG
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License
@@ -15,6 +16,7 @@
 #include <linux/mfd/core.h>
 #include <linux/mfd/rn5t618.h>
 #include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/regmap.h>
 
 static const struct mfd_cell rn5t618_cells[] = {
@@ -59,12 +61,26 @@ static void rn5t618_power_off(void)
 			   RN5T618_SLPCNT_SWPWROFF, RN5T618_SLPCNT_SWPWROFF);
 }
 
+static const struct of_device_id rn5t618_of_match[] = {
+	{ .compatible = "ricoh,rn5t567", .data = (void *)RN5T567 },
+	{ .compatible = "ricoh,rn5t618", .data = (void *)RN5T618 },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, rn5t618_of_match);
+
 static int rn5t618_i2c_probe(struct i2c_client *i2c,
 			     const struct i2c_device_id *id)
 {
+	const struct of_device_id *of_id =
+		of_match_device(rn5t618_of_match, &i2c->dev);
 	struct rn5t618 *priv;
 	int ret;
 
+	if (!of_id) {
+		dev_err(&i2c->dev, "Failed to find matching dt id\n");
+		return -EINVAL;
+	}
+
 	priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
 	if (!priv)
 		return -ENOMEM;
@@ -78,6 +94,8 @@ static int rn5t618_i2c_probe(struct i2c_client *i2c,
 		return ret;
 	}
 
+	priv->variant = (long)of_id->data;
+
 	ret = devm_mfd_add_devices(&i2c->dev, -1, rn5t618_cells,
 				   ARRAY_SIZE(rn5t618_cells), NULL, 0, NULL);
 	if (ret) {
@@ -105,12 +123,6 @@ static int rn5t618_i2c_remove(struct i2c_client *i2c)
 	return 0;
 }
 
-static const struct of_device_id rn5t618_of_match[] = {
-	{ .compatible = "ricoh,rn5t618" },
-	{ }
-};
-MODULE_DEVICE_TABLE(of, rn5t618_of_match);
-
 static const struct i2c_device_id rn5t618_i2c_id[] = {
 	{ }
 };
@@ -129,5 +141,5 @@ static struct i2c_driver rn5t618_i2c_driver = {
 module_i2c_driver(rn5t618_i2c_driver);
 
 MODULE_AUTHOR("Beniamino Galvani <b.galvani at gmail.com>");
-MODULE_DESCRIPTION("Ricoh RN5T618 MFD driver");
+MODULE_DESCRIPTION("Ricoh RN5T567/618 MFD driver");
 MODULE_LICENSE("GPL v2");
diff --git a/include/linux/mfd/rn5t618.h b/include/linux/mfd/rn5t618.h
index c72d534..54179c2 100644
--- a/include/linux/mfd/rn5t618.h
+++ b/include/linux/mfd/rn5t618.h
@@ -20,6 +20,7 @@
 #define RN5T618_OTPVER			0x01
 #define RN5T618_IODAC			0x02
 #define RN5T618_VINDAC			0x03
+#define RN5T618_OUT32KEN		0x05
 #define RN5T618_CPUCNT			0x06
 #define RN5T618_PSWR			0x07
 #define RN5T618_PONHIS			0x09
@@ -38,6 +39,7 @@
 #define RN5T618_DC1_SLOT		0x16
 #define RN5T618_DC2_SLOT		0x17
 #define RN5T618_DC3_SLOT		0x18
+#define RN5T618_DC4_SLOT		0x19
 #define RN5T618_LDO1_SLOT		0x1b
 #define RN5T618_LDO2_SLOT		0x1c
 #define RN5T618_LDO3_SLOT		0x1d
@@ -54,12 +56,16 @@
 #define RN5T618_DC2CTL2			0x2f
 #define RN5T618_DC3CTL			0x30
 #define RN5T618_DC3CTL2			0x31
+#define RN5T618_DC4CTL			0x32
+#define RN5T618_DC4CTL2			0x33
 #define RN5T618_DC1DAC			0x36
 #define RN5T618_DC2DAC			0x37
 #define RN5T618_DC3DAC			0x38
+#define RN5T618_DC4DAC			0x39
 #define RN5T618_DC1DAC_SLP		0x3b
 #define RN5T618_DC2DAC_SLP		0x3c
 #define RN5T618_DC3DAC_SLP		0x3d
+#define RN5T618_DC4DAC_SLP		0x3e
 #define RN5T618_DCIREN			0x40
 #define RN5T618_DCIRQ			0x41
 #define RN5T618_DCIRMON			0x42
@@ -221,8 +227,14 @@ enum {
 	RN5T618_REG_NUM,
 };
 
+enum {
+	RN5T567 = 0,
+	RN5T618,
+};
+
 struct rn5t618 {
 	struct regmap *regmap;
+	long variant;
 };
 
 #endif /* __LINUX_MFD_RN5T618_H */
-- 
2.8.3




More information about the linux-arm-kernel mailing list