[PATCH v14 0/17] Add Analogix Core Display Port Driver
Yakir Yang
ykk at rock-chips.com
Sun Jul 31 18:49:30 PDT 2016
On 07/29/2016 04:38 PM, Tomeu Vizoso wrote:
> On 5 April 2016 at 04:06, Yakir Yang <ykk at rock-chips.com> wrote:
>> Hi Daniel,
>>
>>
>> On 03/31/2016 06:15 PM, Daniel Vetter wrote:
>>> On Mon, Feb 15, 2016 at 07:08:05PM +0800, Yakir Yang wrote:
>>>> Hi all,
>>>>
>>>> The Samsung Exynos eDP controller and Rockchip RK3288 eDP controller
>>>> share the same IP, so a lot of parts can be re-used. I split the common
>>>> code into bridge directory, then rk3288 and exynos only need to keep
>>>> some platform code. Cause I can't find the exact IP name of exynos dp
>>>> controller, so I decide to name dp core driver with "analogix" which I
>>>> find in rk3288 eDP TRM
>>>>
>>>> But there are still three light registers setting different between
>>>> exynos and rk3288.
>>>> 1. RK3288 have five special pll registers which not indicate in exynos
>>>> dp controller.
>>>> 2. The address of DP_PHY_PD(dp phy power manager register) are different
>>>> between rk3288 and exynos.
>>>> 3. Rk3288 and exynos have different setting with AUX_HW_RETRY_CTL(dp
>>>> debug
>>>> register).
>>>>
>>>> Due to Mark Yao have introduced the ATOMIC support to Rockchip drm, so
>>>> it's
>>>> okay to use the ATOMIC helpers functions in connector_funcs. No need to
>>>> splict
>>>> the connector init to platform driver anymore, and this is the biggest
>>>> change
>>>> since version 11.
>>>>
>>>> This v14 didn't have lots of new changes which seems not the correct time
>>>> to
>>>> upgrade the version number, but I have changed ordering of patches
>>>> (adding 2
>>>> more, and removing 2 out). Especially to prevent confusing people, so I
>>>> updated
>>>> the whole series.
>>> So I'm jumping into this part way late, but just noticed (well Thierry
>>> pointed this out to me) that the exynos dp driver reinvents all the dp and
>>> dp-aux helpers we already. That's somewhat okish for a private driver (and
>>> exynos has a reputation for that kind of stuff), but imo not ok for a
>>> shared driver.
>>>
>>> Not saying this should block merging this patch, but it really needs to be
>>> addressed. All the dp aux and edid read code in the current
>>> exynos_dp_core/reg.c files needs to be replaced with dp helpers and the
>>> core i2c edid reading code.
>>>
>>> Who's going to sign up to do this?
>>
>> Volunteer to that, after finish this thread, I would send new series to
>> switch to take use of dp helper.
> Hi Yakir,
>
> do you have plans to do this work in the short term? If not, I can tackle it.
Wow, that would be great if you like to tackle it :-D
I always keep this in my mind, but haven't found an chance
to finish it. I would like to sit in your Cc list when you post
them out ;)
Best Regards,
- Yakir
> Regards,
>
> Tomeu
>
>> :-D
>> - Yakir
>>
>>
>>> -Daniel
>>>
>>>> Thanks,
>>>> - Yakir
>>>>
>>>>
>>>> Changes in v14:
>>>> - Rebase the new changes in imx-dp driver
>>>> - Split up this patch into 3 parts, make this easy to review (Heiko)
>>>> - Remove the Rockchip DP PHY to an separate thread (Heiko)
>>>> https://patchwork.kernel.org/patch/8312701/
>>>>
>>>> Changes in v13:
>>>> - Use .enable instead of preprare/commit in encoder_helper_funcs (Heiko)
>>>> - Fix the missing parameters with drm_encoder_init() helper function.
>>>> (Heiko)
>>>>
>>>> Changes in v12:
>>>> - Move the connector init to analogix_dp driver, and using ATOMIC helper
>>>> (Heiko)
>>>> - Add the ack from Jingoo
>>>> - Remove the enum link_rate_type struct, using the marcos in
>>>> drm_dp_helper.h (Jingoo)
>>>>
>>>> Changes in v11:
>>>> - Uses tabs to fix the indentation issues in analogix_dp_core.h (Heiko)
>>>> - Rename the "analogix,need-force-hpd" to common 'force-hpd' (Rob)
>>>> - Add the ack from Rob Herring
>>>> - Revert parts of Gustavo Padovan's changes in commit:
>>>> drm/exynos: do not start enabling DP at bind() phase
>>>> Add dp phy poweron function in bind time.
>>>> - Move the panel prepare from get_modes time to bind time, and move
>>>> the panel unprepare from bridge->disable to unbind time. (Heiko)
>>>>
>>>> Changes in v10:
>>>> - Add the ack from Rob Herring
>>>> - Correct the ROCKCHIP_ANALOGIX_DP indentation in Kconfig to tabs here
>>>> (Heiko)
>>>> - Add the ack from Rob Herring
>>>> - Remove the surplus "plat_data" check. (Heiko)
>>>> - switch (dp->plat_data && dp->plat_data->dev_type) {
>>>> + switch (dp->plat_data->dev_type) {
>>>>
>>>> Changes in v9:
>>>> - Document more details for 'ports' property.
>>>>
>>>> Changes in v8:
>>>> - Correct the right document path of display-timing.txt (Heiko)
>>>> - Correct the misspell of 'from' to 'frm'. (Heiko)
>>>> - Modify the commit subject name. (Heiko)
>>>>
>>>> Changes in v7:
>>>> - Back to use the of_property_read_bool() interfacs to provoid backward
>>>> compatibility of "hsync-active-high" "vsync-active-high" "interlaced"
>>>> to avoid -EOVERFLOW error (Krzysztof)
>>>>
>>>> Changes in v6:
>>>> - Fix the Kconfig recursive dependency (Javier)
>>>> - Fix Peach Pit hpd property name error:
>>>> - hpd-gpio = <&gpx2 6 0>;
>>>> + hpd-gpios = <&gpx2 6 0>;
>>>>
>>>> Changes in v5:
>>>> - Correct the check condition of gpio_is_valid when driver try to get
>>>> the "hpd-gpios" DT propery. (Heiko)
>>>> - Move the platform attach callback in the front of core driver bridge
>>>> attch function. Cause once platform failed at attach, core driver
>>>> should
>>>> still failed, so no need to init connector before platform attached
>>>> (Krzysztof)
>>>> - Keep code style no changes with the previous exynos_dp_code.c in this
>>>> patch, and update commit message about the new export symbol
>>>> (Krzysztof)
>>>> - Gather the device type patch (v4 11/16) into this one. (Krzysztof)
>>>> - leave out the connector registration to analogix platform driver.
>>>> (Thierry)
>>>> - Resequence this patch after analogix_dp driver have been split
>>>> from exynos_dp code, and rephrase reasonable commit message, and
>>>> remove some controversial style (Krzysztof)
>>>> - analogix_dp_write_byte_to_dpcd(
>>>> - dp, DP_TEST_RESPONSE,
>>>> + analogix_dp_write_byte_to_dpcd(dp,
>>>> + DP_TEST_RESPONSE,
>>>> DP_TEST_EDID_CHECKSUM_WRITE);
>>>> - Switch video timing type to "u32", so driver could use
>>>> "of_property_read_u32"
>>>> to get the backword timing values. Krzysztof suggest me that driver
>>>> could use
>>>> the "of_property_read_bool" to get backword timing values, but that
>>>> interfacs
>>>> would modify the original drm_display_mode timing directly (whether
>>>> those
>>>> properties exists or not).
>>>> - Correct the misspell in commit message. (Krzysztof)
>>>> - Remove the empty line at the end of document, and correct the endpoint
>>>> numbers in the example DT node, and remove the regulator iomux setting
>>>> in driver code while using the pinctl in devicetree instead. (Heiko)
>>>> - Add device type declared, cause the previous "platform device type
>>>> support (v4 11/16)" already merge into (v5 02/14).
>>>> - Implement connector registration code. (Thierry)
>>>> - Split binding doc's from driver changes. (Rob)
>>>> - Add eDP hotplug pinctrl property. (Heiko)
>>>>
>>>> Changes in v4:
>>>> - Update "analogix,hpd-gpios" to "hpd-gpios" DT propery. (Rob)
>>>> - Rename "analogix_dp-exynos.c" file name to "exynos_dp.c" (Jingoo)
>>>> - Create a separate folder for analogix code in bridge/ (Archit)
>>>> - Update commit message more readable. (Jingoo)
>>>> - Adjust the order from 05 to 04
>>>> - Provide backword compatibility with samsung. (Krzysztof)
>>>> - Split all DTS changes, and provide backward compatibility. Mark old
>>>> properties as deprecated but still support them. (Krzysztof)
>>>> - Update "analogix,hpd-gpio" to "hpd-gpios" prop name. (Rob)
>>>> - Deprecated some properties which could parsed from Edid/Mode/DPCD.
>>>> (Thierry)
>>>> "analogix,color-space" & "analogix,color-depth" &
>>>> "analogix,link-rate" & "analogix,lane-count" &
>>>> "analogix,ycbcr-coeff" & "analogix,dynamic-range" &
>>>> "vsync-active-high" & "hsync-active-high" & "interlaces"
>>>> - Separate all DTS changes to a separate patch. (Krzysztof)
>>>> - Remove some deprecated DT properties in rockchip dp document.
>>>> - Seprate the link-rate and lane-count limit out with the device_type
>>>> flag. (Thierry)
>>>> - Take Jingoo suggest, add commit messages.
>>>> - Call drm_panel_prepare() in .get_modes function, ensure panel should
>>>> power on before driver try to read edid message.
>>>>
>>>> Changes in v3:
>>>> - Move exynos's video_timing code to analogix_dp-exynos platform driver,
>>>> add get_modes method to struct analogix_dp_plat_data. (Thierry)
>>>> - Rename some "samsung*" dts propery to "analogix*". (Heiko)
>>>> - The link_rate and lane_count shouldn't config to the DT property value
>>>> directly, but we can take those as hardware limite. For example,
>>>> RK3288
>>>> only support 4 physical lanes of 2.7/1.62 Gbps/lane, so DT property
>>>> would
>>>> like "link-rate = 0x0a" "lane-count = 4". (Thierry)
>>>> - Dynamic parse video timing info from struct drm_display_mode and
>>>> struct drm_display_info. (Thierry)
>>>> - Add devicetree binding documents. (Heiko)
>>>> - Remove sync pol & colorimetry properies from the new analogix dp driver
>>>> devicetree binding. (Thierry)
>>>> - Update the exist exynos dtsi file with the latest DP DT properies.
>>>> - Leave "sclk_edp_24m" to rockchip dp phy driver which name to "24m",
>>>> and leave "sclk_edp" to analogix dp core driver which name to "dp",
>>>> and leave "pclk_edp" to rockchip dp platform driver which name to
>>>> "pclk". (Thierry & Heiko)
>>>> - Add devicetree binding document. (Heiko)
>>>> - Remove "rockchip,panel" DT property, take use of remote point to get
>>>> panel
>>>> node. (Heiko)
>>>> - Add the new function point dp_platdata->get_modes() init.
>>>> - Add "analogix,need-force-hpd" to indicate whether driver need foce
>>>> hpd when hpd detect failed.
>>>> - move dp hpd detect to connector detect function.
>>>> - Add edid modes parse support
>>>>
>>>> Changes in v2:
>>>> - Remove new copyright (Jingoo)
>>>> - Fix compiled failed due to analogix_dp_device misspell
>>>> - Improved commit message more readable, and avoid using some
>>>> uncommon style like bellow: (Joe Preches)
>>>> - retval = exynos_dp_read_bytes_from_i2c(...
>>>> ...);
>>>> + retval =
>>>> + exynos_dp_read_bytes_from_i2c(......);
>>>> - Get panel node with remote-endpoint method, and create devicetree
>>>> binding
>>>> for driver. (Heiko)
>>>> - Remove the clock enable/disbale with "sclk_edp" & "sclk_edp_24m",
>>>> leave those clock to rockchip dp phy driver.
>>>> - Fix compile failed dut to phy_pd_addr variable misspell error
>>>>
>>>> Heiko Stuebner (2):
>>>> drm/exynos: dp: rename implementation specific driver part
>>>> drm: bridge: analogix/dp: rename register constants
>>>>
>>>> Yakir Yang (15):
>>>> drm: bridge: analogix/dp: split exynos dp driver to bridge directory
>>>> drm: bridge: analogix/dp: fix some obvious code style
>>>> drm: bridge: analogix/dp: remove duplicate configuration of link rate
>>>> and link count
>>>> drm: bridge: analogix/dp: dynamic parse sync_pol & interlace &
>>>> dynamic_range
>>>> dt-bindings: add document for analogix display port driver
>>>> ARM: dts: exynos/dp: remove some properties that deprecated by
>>>> analogix_dp driver
>>>> drm: rockchip: dp: add rockchip platform dp driver
>>>> dt-bindings: add document for rockchip variant of analogix_dp
>>>> drm: bridge: analogix/dp: add some rk3288 special registers setting
>>>> drm: bridge: analogix/dp: add max link rate and lane count limit for
>>>> RK3288
>>>> drm: bridge: analogix/dp: try force hpd after plug in lookup failed
>>>> drm: bridge: analogix/dp: move hpd detect to connector detect function
>>>> drm: bridge: analogix/dp: add edid modes parse in get_modes method
>>>> drm: bridge: analogix/dp: add panel prepare/unprepare in
>>>> suspend/resume time
>>>> drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable
>>>> time
>>>>
>>>> .../bindings/display/bridge/analogix_dp.txt | 52 +
>>>> .../bindings/display/exynos/exynos_dp.txt | 93 +-
>>>> .../display/rockchip/analogix_dp-rockchip.txt | 92 ++
>>>> arch/arm/boot/dts/exynos5250-arndale.dts | 2 -
>>>> arch/arm/boot/dts/exynos5250-smdk5250.dts | 2 -
>>>> arch/arm/boot/dts/exynos5250-snow-common.dtsi | 4 +-
>>>> arch/arm/boot/dts/exynos5250-spring.dts | 4 +-
>>>> arch/arm/boot/dts/exynos5420-peach-pit.dts | 4 +-
>>>> arch/arm/boot/dts/exynos5420-smdk5420.dts | 2 -
>>>> arch/arm/boot/dts/exynos5800-peach-pi.dts | 2 -
>>>> drivers/gpu/drm/bridge/Kconfig | 2 +
>>>> drivers/gpu/drm/bridge/Makefile | 1 +
>>>> drivers/gpu/drm/bridge/analogix/Kconfig | 3 +
>>>> drivers/gpu/drm/bridge/analogix/Makefile | 1 +
>>>> drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 1430
>>>> ++++++++++++++++++
>>>> drivers/gpu/drm/bridge/analogix/analogix_dp_core.h | 281 ++++
>>>> drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c | 1320
>>>> +++++++++++++++++
>>>> .../analogix/analogix_dp_reg.h} | 270 ++--
>>>> drivers/gpu/drm/exynos/Kconfig | 3 +-
>>>> drivers/gpu/drm/exynos/Makefile | 2 +-
>>>> drivers/gpu/drm/exynos/exynos_dp.c | 324 +++++
>>>> drivers/gpu/drm/exynos/exynos_dp_core.c | 1510
>>>> --------------------
>>>> drivers/gpu/drm/exynos/exynos_dp_core.h | 282 ----
>>>> drivers/gpu/drm/exynos/exynos_dp_reg.c | 1263
>>>> ----------------
>>>> drivers/gpu/drm/rockchip/Kconfig | 9 +
>>>> drivers/gpu/drm/rockchip/Makefile | 1 +
>>>> drivers/gpu/drm/rockchip/analogix_dp-rockchip.c | 384 +++++
>>>> include/drm/bridge/analogix_dp.h | 41 +
>>>> 28 files changed, 4115 insertions(+), 3269 deletions(-)
>>>> create mode 100644
>>>> Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
>>>> create mode 100644
>>>> Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt
>>>> create mode 100644 drivers/gpu/drm/bridge/analogix/Kconfig
>>>> create mode 100644 drivers/gpu/drm/bridge/analogix/Makefile
>>>> create mode 100644 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
>>>> create mode 100644 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
>>>> create mode 100644 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
>>>> rename drivers/gpu/drm/{exynos/exynos_dp_reg.h =>
>>>> bridge/analogix/analogix_dp_reg.h} (62%)
>>>> create mode 100644 drivers/gpu/drm/exynos/exynos_dp.c
>>>> delete mode 100644 drivers/gpu/drm/exynos/exynos_dp_core.c
>>>> delete mode 100644 drivers/gpu/drm/exynos/exynos_dp_core.h
>>>> delete mode 100644 drivers/gpu/drm/exynos/exynos_dp_reg.c
>>>> create mode 100644 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
>>>> create mode 100644 include/drm/bridge/analogix_dp.h
>>>>
>>>> --
>>>> 1.9.1
>>>>
>>>>
>>>> _______________________________________________
>>>> dri-devel mailing list
>>>> dri-devel at lists.freedesktop.org
>>>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>>
>>
>> _______________________________________________
>> dri-devel mailing list
>> dri-devel at lists.freedesktop.org
>> https://lists.freedesktop.org/mailman/listinfo/dri-devel
>
>
More information about the linux-arm-kernel
mailing list