[PATCH v2 1/3] drm/mediatek: do mtk_hdmi_send_infoframe after HDMI clock enable

[Bibby Hsieh]

Hi, Philipp,

Thanks for your review.

On Wed, 2016-07-27 at 11:27 +0200, Philipp Zabel wrote:
> Am Mittwoch, den 27.07.2016, 16:31 +0800 schrieb Bibby Hsieh:
> > From: Junzhi Zhao <junzhi.zhao at mediatek.com>
> > 
> > The mtk_hdmi_send_infoframe have to
> > be run after PLL and PIXEL clock of HDMI enable.
> > Make sure that HDMI inforframes can be sent
> > successfully.
> > 
> > Signed-off-by: Junzhi Zhao <junzhi.zhao at mediatek.com>
> > Signed-off-by: Bibby Hsieh <bibby.hsieh at mediatek.com>
> > ---
> >  drivers/gpu/drm/mediatek/mtk_hdmi.c |   19 ++++++++++++-------
> >  1 file changed, 12 insertions(+), 7 deletions(-)
> > 
> > diff --git a/drivers/gpu/drm/mediatek/mtk_hdmi.c b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > index ba812ef..d8609f5 100644
> > --- a/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > +++ b/drivers/gpu/drm/mediatek/mtk_hdmi.c
> > @@ -1133,12 +1133,6 @@ static int mtk_hdmi_output_set_display_mode(struct mtk_hdmi *hdmi,
> >  	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_aud_output_config(hdmi, mode);
> >  
> > -	mtk_hdmi_setup_audio_infoframe(hdmi);
> > -	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > -	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > -	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > -		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > -
> >  	mtk_hdmi_hw_vid_black(hdmi, false);
> >  	mtk_hdmi_hw_aud_unmute(hdmi);
> >  	mtk_hdmi_hw_send_av_unmute(hdmi);
> > @@ -1401,14 +1395,25 @@ static void mtk_hdmi_bridge_pre_enable(struct drm_bridge *bridge)
> >  	hdmi->powered = true;
> >  }
> >  
> > +static void mtk_hdmi_send_infoframe(struct mtk_hdmi *hdmi,
> > +				    struct drm_display_mode *mode)
> > +{
> > +	mtk_hdmi_setup_audio_infoframe(hdmi);
> > +	mtk_hdmi_setup_avi_infoframe(hdmi, mode);
> > +	mtk_hdmi_setup_spd_infoframe(hdmi, "mediatek", "On-chip HDMI");
> > +	if (mode->flags & DRM_MODE_FLAG_3D_MASK)
> > +		mtk_hdmi_setup_vendor_specific_infoframe(hdmi, mode);
> > +}
> > +
> >  static void mtk_hdmi_bridge_enable(struct drm_bridge *bridge)
> >  {
> >  	struct mtk_hdmi *hdmi = hdmi_ctx_from_bridge(bridge);
> >  
> > +	phy_power_on(hdmi->phy);
> >  	mtk_hdmi_output_set_display_mode(hdmi, &hdmi->mode);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PLL]);
> >  	clk_prepare_enable(hdmi->clk[MTK_HDMI_CLK_HDMI_PIXEL]);
> > -	phy_power_on(hdmi->phy);
> 
> This change is not described in the patch description. Why is the phy
> power on moved after the pixel clock enable?
> 
Ok, will rollback it.
> > +	mtk_hdmi_send_infoframe(hdmi, &hdmi->mode);
> >  
> >  	hdmi->enabled = true;
> >  }
> 
> regards
> Philipp
> 

-- 
Bibby