[PATCH v2] drivers/perf: arm-pmu: Handle per-interrupt affinity mask
Geert Uytterhoeven
geert at linux-m68k.org
Tue Jul 19 06:25:30 PDT 2016
Hi Marc, Catalin, Will,
On Wed, Jul 6, 2016 at 4:33 PM, Marc Zyngier <marc.zyngier at arm.com> wrote:
> On a big-little system, PMUs can be wired to CPUs using per CPU
> interrups (PPI). In this case, it is important to make sure that
> the enable/disable do happen on the right set of CPUs.
>
> So instead of relying on the interrupt-affinity property, we can
> use the actual percpu affinity that DT exposes as part of the
> interrupt specifier. The DT binding is also updated to reflect
> the fact that the interrupt-affinity property shouldn't be used
> in that case.
>
> Signed-off-by: Marc Zyngier <marc.zyngier at arm.com>
> ---
> * From v1:
> - propagate the error if irq_get_percpu_devid_partition fails
This patch, which is commit 19a469a58720ea96 in arm64/for-next/core, broke
the PMU on r8a7740/armadillo800eva:
-hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7
counters available
+hw perfevents: /pmu: failed to probe PMU!
+hw perfevents: /pmu: failed to register PMU devices!
+armv7-pmu: probe of pmu failed with error -22
This is a single-core Cortex A9.
> Documentation/devicetree/bindings/arm/pmu.txt | 4 +++-
> drivers/perf/arm_pmu.c | 27 ++++++++++++++++++++++-----
> 2 files changed, 25 insertions(+), 6 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/pmu.txt b/Documentation/devicetree/bindings/arm/pmu.txt
> index 74d5417..61c8b46 100644
> --- a/Documentation/devicetree/bindings/arm/pmu.txt
> +++ b/Documentation/devicetree/bindings/arm/pmu.txt
> @@ -39,7 +39,9 @@ Optional properties:
> When using a PPI, specifies a list of phandles to CPU
> nodes corresponding to the set of CPUs which have
> a PMU of this type signalling the PPI listed in the
> - interrupts property.
> + interrupts property, unless this is already specified
> + by the PPI interrupt specifier itself (in which case
> + the interrupt-affinity property shouldn't be present).
>
> This property should be present when there is more than
> a single SPI.
On a single core, there's only a single SPI, hence there's no need for an
"interrupt-affinity" property.
> diff --git a/drivers/perf/arm_pmu.c b/drivers/perf/arm_pmu.c
> index 140436a..8e4d7f5 100644
> --- a/drivers/perf/arm_pmu.c
> +++ b/drivers/perf/arm_pmu.c
> @@ -961,9 +964,23 @@ static int of_pmu_irq_cfg(struct arm_pmu *pmu)
> i++;
> } while (1);
>
> - /* If we didn't manage to parse anything, claim to support all CPUs */
> - if (cpumask_weight(&pmu->supported_cpus) == 0)
> - cpumask_setall(&pmu->supported_cpus);
> + /* If we didn't manage to parse anything, try the interrupt affinity */
> + if (cpumask_weight(&pmu->supported_cpus) == 0) {
> + if (!using_spi) {
However, using_spi is never set to true in the absence of that property,
causing the wrong branch to be taken...
> + /* If using PPIs, check the affinity of the partition */
> + int ret, irq;
> +
> + irq = platform_get_irq(pdev, 0);
> + ret = irq_get_percpu_devid_partition(irq, &pmu->supported_cpus);
... and ret to become -22 here.
> + if (ret) {
> + kfree(irqs);
> + return ret;
> + }
> + } else {
> + /* Otherwise default to all CPUs */
> + cpumask_setall(&pmu->supported_cpus);
> + }
> + }
>
> /* If we matched up the IRQ affinities, use them to route the SPIs */
> if (using_spi && i == pdev->num_resources)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
More information about the linux-arm-kernel
mailing list