[PATCH 4/4] usb: chipidea: imx: set over current polarity per dts setting
Peter Chen
hzpeterchen at gmail.com
Mon Jul 18 19:44:50 PDT 2016
On Tue, Jul 19, 2016 at 02:31:41AM +0000, Jun Li wrote:
> Hi
>
> > -----Original Message-----
> > From: Peter Chen [mailto:hzpeterchen at gmail.com]
> > Sent: Tuesday, July 19, 2016 9:57 AM
> > To: Jun Li <jun.li at nxp.com>
> > Cc: Peter Chen <peter.chen at nxp.com>; robh+dt at kernel.org;
> > shawnguo at kernel.org; devicetree at vger.kernel.org; linux-usb at vger.kernel.org;
> > linux-arm-kernel at lists.infradead.org
> > Subject: Re: [PATCH 4/4] usb: chipidea: imx: set over current polarity per
> > dts setting
> >
> > On Mon, Jul 18, 2016 at 07:15:47PM +0800, Li Jun wrote:
> > > With over-current-polarity property added, imx usb over current
> > > polarity can be configed to be low or high active, since the default
> > > setting value(0) is for active high, so keep this setting for those
> > > legacy platforms without this property specified.
> > >
> > > Signed-off-by: Li Jun <jun.li at nxp.com>
> > > ---
> > > drivers/usb/chipidea/ci_hdrc_imx.c | 9 +++++++++
> > > drivers/usb/chipidea/ci_hdrc_imx.h | 1 +
> > > drivers/usb/chipidea/usbmisc_imx.c | 30 +++++++++++++++++++++++++-----
> > > 3 files changed, 35 insertions(+), 5 deletions(-)
> > >
> > > diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c
> > > b/drivers/usb/chipidea/ci_hdrc_imx.c
> > > index dedc33e..61e712b 100644
> > > --- a/drivers/usb/chipidea/ci_hdrc_imx.c
> > > +++ b/drivers/usb/chipidea/ci_hdrc_imx.c
> > > @@ -140,6 +140,15 @@ static struct imx_usbmisc_data
> > *usbmisc_get_init_data(struct device *dev)
> > > if (of_find_property(np, "disable-over-current", NULL))
> > > data->disable_oc = 1;
> > >
> > > + if (!of_property_read_u32(np, "over-current-polarity", &ret))
> > > + data->oc_polarity = ret ? 1 : 0;
> > > + else
> > > + /*
> > > + * Keep the oc polarity setting of legacy
> > > + * platforms unchanged.
> > > + */
> > > + data->oc_polarity = 1;
> >
> > We may can't ensure that, since there are lots of i.mx platforms, eg from
> > imx27 to imx7.
> >
> > If the user does not assign oc polarity at DT, we need to read it from
> > register.
>
> I suppose old platforms (other than i.mx6&7) should set either
> "over-current-polarity" or "disable-over-current" if want to use
> "data->oc_polarity".
>
The user may use old dtb and the latest kernel, so the introduced
DT property should not affect old dtb platforms.
> Do you mean read the register value before set "data->oc_polarity" here?
yes, if there is a dts property, read it from DT; else, read it from the register.
if (!of_property_read_u32(np, "over-current-polarity", &ret))
data->oc_polarity = ret ? 1 : 0;
else
/*
* Keep the oc polarity setting of legacy
* platforms unchanged.
*/
data->oc_polarity = readl(oc_polarity);
Then, when you set register for oc polarity, you can depend on the
flag.
reg = readl(usbmisc->base + data->index * 4);
value = data->oc_polarity ? MX6_BM_OVER_CUR_POLARITY : 0;
writel(reg | value, usbmisc->base + data->index * 4);
> Even with that, as I still can't ensure all i.mx platforms have the same
> mapping:
> 0 <--> active high.
> 1 <--> active low.
> How should I set "data->oc_polarity" accordingly?
Just keep current register value unchanging if there is no dts property.
Peter
> Li Jun
> >
> > Peter
> > > +
> > > if (of_find_property(np, "external-vbus-divider", NULL))
> > > data->evdo = 1;
> > >
> > > diff --git a/drivers/usb/chipidea/ci_hdrc_imx.h
> > > b/drivers/usb/chipidea/ci_hdrc_imx.h
> > > index 635717e..409aa5ca8 100644
> > > --- a/drivers/usb/chipidea/ci_hdrc_imx.h
> > > +++ b/drivers/usb/chipidea/ci_hdrc_imx.h
> > > @@ -17,6 +17,7 @@ struct imx_usbmisc_data {
> > > int index;
> > >
> > > unsigned int disable_oc:1; /* over current detect disabled */
> > > + unsigned int oc_polarity:1; /* over current polarity if oc enabled
> > > +*/
> > > unsigned int evdo:1; /* set external vbus divider option */ };
> > >
> > > diff --git a/drivers/usb/chipidea/usbmisc_imx.c
> > > b/drivers/usb/chipidea/usbmisc_imx.c
> > > index ab8b027..193dbe4 100644
> > > --- a/drivers/usb/chipidea/usbmisc_imx.c
> > > +++ b/drivers/usb/chipidea/usbmisc_imx.c
> > > @@ -56,6 +56,7 @@
> > >
> > > #define MX6_BM_NON_BURST_SETTING BIT(1)
> > > #define MX6_BM_OVER_CUR_DIS BIT(7)
> > > +#define MX6_BM_OVER_CUR_POLARITY BIT(8)
> > > #define MX6_BM_WAKEUP_ENABLE BIT(10)
> > > #define MX6_BM_ID_WAKEUP BIT(16)
> > > #define MX6_BM_VBUS_WAKEUP BIT(17)
> > > @@ -266,11 +267,18 @@ static int usbmisc_imx6q_init(struct
> > > imx_usbmisc_data *data)
> > >
> > > spin_lock_irqsave(&usbmisc->lock, flags);
> > >
> > > + reg = readl(usbmisc->base + data->index * 4);
> > > if (data->disable_oc) {
> > > - reg = readl(usbmisc->base + data->index * 4);
> > > - writel(reg | MX6_BM_OVER_CUR_DIS,
> > > - usbmisc->base + data->index * 4);
> > > + reg |= MX6_BM_OVER_CUR_DIS;
> > > + } else if (data->oc_polarity == 1) {
> > > + /* High active */
> > > + reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY);
> > > + } else {
> > > + /* Low active */
> > > + reg &= ~MX6_BM_OVER_CUR_DIS;
> > > + reg |= MX6_BM_OVER_CUR_POLARITY;
> > > }
> > > + writel(reg, usbmisc->base + data->index * 4);
> > >
> > > /* SoC non-burst setting */
> > > reg = readl(usbmisc->base + data->index * 4); @@ -365,10 +373,18 @@
> > > static int usbmisc_imx7d_init(struct imx_usbmisc_data *data)
> > > return -EINVAL;
> > >
> > > spin_lock_irqsave(&usbmisc->lock, flags);
> > > + reg = readl(usbmisc->base);
> > > if (data->disable_oc) {
> > > - reg = readl(usbmisc->base);
> > > - writel(reg | MX6_BM_OVER_CUR_DIS, usbmisc->base);
> > > + reg |= MX6_BM_OVER_CUR_DIS;
> > > + } else if (data->oc_polarity == 1) {
> > > + /* High active */
> > > + reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY);
> > > + } else {
> > > + /* Low active */
> > > + reg &= ~MX6_BM_OVER_CUR_DIS;
> > > + reg |= MX6_BM_OVER_CUR_POLARITY;
> > > }
> > > + writel(reg, usbmisc->base);
> > >
> > > reg = readl(usbmisc->base + MX7D_USBNC_USB_CTRL2);
> > > reg &= ~MX7D_USB_VBUS_WAKEUP_SOURCE_MASK;
> > > @@ -492,6 +508,10 @@ static const struct of_device_id
> > usbmisc_imx_dt_ids[] = {
> > > .compatible = "fsl,imx6ul-usbmisc",
> > > .data = &imx6sx_usbmisc_ops,
> > > },
> > > + {
> > > + .compatible = "fsl,imx7d-usbmisc",
> > > + .data = &imx7d_usbmisc_ops,
> > > + },
> > > { /* sentinel */ }
> > > };
> > > MODULE_DEVICE_TABLE(of, usbmisc_imx_dt_ids);
> > > --
> > > 1.9.1
> > >
> > >
> > > _______________________________________________
> > > linux-arm-kernel mailing list
> > > linux-arm-kernel at lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> >
> > --
> >
> > Best Regards,
> > Peter Chen
--
Best Regards,
Peter Chen
More information about the linux-arm-kernel
mailing list