[PATCH] arm64: dts: rockchip: Add basic support for orion-r68
Shawn Lin
shawn.lin at rock-chips.com
Thu Jul 14 18:00:13 PDT 2016
Hi Matthias,
Just some comment for mmc stuff. :)
在 2016/7/14 20:28, Matthias Brugger 写道:
> This patch adds basic support for the Tronsmart orion r86 set-top-box.
>
> Signed-off-by: Matthias Brugger <mbrugger at suse.com>
> ---
> Changes since v1:
> - change memory node to 2GB
> - change compatible and file name
> - add uart4
> - add second led
>
> Documentation/devicetree/bindings/arm/rockchip.txt | 4 +
> arch/arm64/boot/dts/rockchip/Makefile | 1 +
> .../boot/dts/rockchip/rk3368-orion-r68-meta.dts | 382 +++++++++++++++++++++
> 3 files changed, 387 insertions(+)
> create mode 100644 arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
>
> diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
> index 715d960..1d5c65e0 100644
> --- a/Documentation/devicetree/bindings/arm/rockchip.txt
> +++ b/Documentation/devicetree/bindings/arm/rockchip.txt
> @@ -110,3 +110,7 @@ Rockchip platforms device tree bindings
> - Rockchip RK3399 evb:
> Required root node properties:
> - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
> +
> +- Tronsmart Orion R68 Meta
> + Required root node properties:
> + - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
> diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
> index 7037a16..87669f6 100644
> --- a/arch/arm64/boot/dts/rockchip/Makefile
> +++ b/arch/arm64/boot/dts/rockchip/Makefile
> @@ -1,5 +1,6 @@
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-evb-act8846.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-geekbox.dtb
> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-orion-r68-meta.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3368-r88.dtb
> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3399-evb.dtb
>
> diff --git a/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
> new file mode 100644
> index 0000000..8c8671f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/rockchip/rk3368-orion-r68-meta.dts
> @@ -0,0 +1,382 @@
> +/*
> + * Copyright (c) 2016 Matthias Brugger <mbrugger at suse.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "rk3368.dtsi"
> +
> +/ {
> + model = "Rockchip Orion R68";
> + compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
> +
> + chosen {
> + stdout-path = "serial2:115200n8";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0x0 0x0 0x0 0x80000000>;
> + };
> +
> + emmc_pwrseq: emmc-pwrseq {
> + compatible = "mmc-pwrseq-emmc";
> + pinctrl-0 = <&emmc_reset>;
> + pinctrl-names = "default";
> + reset-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
> + };
> +
> + ext_gmac: external-gmac-clock {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <125000000>;
> + clock-output-names = "ext_gmac";
> + };
> +
> + keys: gpio-keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pwr_key>;
> +
> + button at 0 {
> + gpio-key,wakeup = <1>;
> + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>;
> + label = "GPIO Power";
> + linux,code = <116>;
> + };
> + };
> +
> + leds: gpio-leds {
> + compatible = "gpio-leds";
> +
> + red {
> + gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>;
> + label = "orion:red:led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&led_ctl>;
> + default-state = "on";
> + };
> +
> + blue {
> + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
> + label = "orion:blue:led";
> + pinctrl-names = "default";
> + pinctrl-0 = <&stby_pwren>;
> + default-state = "off";
> + };
> + };
> +
> + vcc_18: vcc18-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_18";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + /* supplies both host and otg */
> + vcc_host: vcc-host-regulator {
> + compatible = "regulator-fixed";
> + gpio = <&gpio0 4 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&host_vbus_drv>;
> + regulator-name = "vcc_host";
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vccio_sd: vcc-io-sd-regulator {
> + regulator-name= "vccio_sd";
> + gpio = <&gpio0 9 GPIO_ACTIVE_LOW>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
so, I guess your r68 board won't support sd 3.0?
> + };
> +
> + vcc_sd: vcc-sd-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sd";
> + gpio = <&gpio3 11 GPIO_ACTIVE_LOW>;
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_io: vcc-io-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_io";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + vcc_lan: vcc-lan-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_lan";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vcc_sys: vcc-sys-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_sys";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + vccio_wl: vccio-wl-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vccio_wl";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_io>;
> + };
> +
> + vdd_10: vdd-10-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_10";
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + cap-mmc-highspeed;
> + disable-wp;
> + mmc-pwrseq = <&emmc_pwrseq>;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>;
> + status = "okay";
> +};
> +
> +&gmac {
> + assigned-clocks = <&cru SCLK_MAC>;
> + assigned-clock-parents = <&ext_gmac>;
> + phy-supply = <&vcc_lan>;
> + phy-mode = "rgmii";
> + clock_in_out = "input";
> + snps,reset-gpio = <&gpio3 12 0>;
> + snps,reset-active-low;
> + snps,reset-delays-us = <0 10000 1000000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + tx_delay = <0x30>;
> + rx_delay = <0x10>;
> + status = "ok";
> +};
> +
> +&i2c0 {
> + status = "okay";
> +
> + vdd_cpu: syr827 at 40 {
> + compatible = "silergy,syr827";
> + reg = <0x40>;
> + fcs,suspend-voltage-selector = <1>;
> + regulator-name = "vdd_cpu";
> + regulator-enable-ramp-delay = <300>;
> + regulator-min-microvolt = <712500>;
> + regulator-max-microvolt = <1500000>;
> + regulator-ramp-delay = <8000>;
> + regulator-always-on;
> + regulator-boot-on;
> + vin-supply = <&vcc_sys>;
> + };
> +
> + hym8563: hym8563 at 51 {
> + compatible = "haoyu,hym8563";
> + reg = <0x51>;
> + #clock-cells = <0>;
> + clock-frequency = <32768>;
> + clock-output-names = "xin32k";
> + /* rtc_int is not connected */
> + };
> +};
> +
> +&pinctrl {
> + pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma {
> + bias-disable;
> + drive-strength = <8>;
> + };
> +
> + pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma {
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + emmc {
> + emmc_bus8: emmc-bus8 {
> + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 19 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 20 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 21 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 22 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 23 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 24 RK_FUNC_2 &pcfg_pull_up_drv_8ma>,
> + <1 25 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + emmc-clk {
> + rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none_drv_8ma>;
> + };
> +
> + emmc-cmd {
> + rockchip,pins = <1 26 RK_FUNC_2 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + emmc_reset: emmc-reset {
> + rockchip,pins = <2 3 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + keys {
> + pwr_key: pwr-key {
> + rockchip,pins = <0 5 RK_FUNC_GPIO &pcfg_pull_down>;
> + };
> + };
> +
> + leds {
> + stby_pwren: stby-pwren {
> + rockchip,pins = <0 12 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> +
> + led_ctl: led-ctl {
> + rockchip,pins = <3 29 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + sdmmc {
> + sdmmc_clk: sdmmc-clk {
> + rockchip,pins = <2 9 RK_FUNC_1 &pcfg_pull_none_drv_8ma>;
> + };
> +
> + sdmmc_cmd: sdmmc-cmd {
> + rockchip,pins = <2 10 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_cd: sdmmc-cd {
> + rockchip,pins = <2 11 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_bus1: sdmmc-bus1 {
> + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> +
> + sdmmc_bus4: sdmmc-bus4 {
> + rockchip,pins = <2 5 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 6 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 7 RK_FUNC_1 &pcfg_pull_up_drv_8ma>,
> + <2 8 RK_FUNC_1 &pcfg_pull_up_drv_8ma>;
> + };
> + };
> +
> + usb {
> + host_vbus_drv: host-vbus-drv {
> + rockchip,pins = <0 4 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +};
> +
> +&saradc {
> + vref-supply = <&vcc_18>;
> + status = "okay";
> +};
> +
> +&sdmmc {
> + clock-frequency = <50000000>;
> + clock-freq-min-max = <400000 50000000>;
> + cap-sd-highspeed;
> + supports-sd;
This's not a upstream property.
> + broken-cd;
sdmmc controller of rk3368 isn't broken. Could you remove it？
> + card-detect-delay = <200>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_bus4>;
> + bus-width = <4>;
> + num-slots = <1>;
> + ignore-pm-notify;
ignore-pm-notify is from AOSP but not upstream mmc. You should remove
it.
> + keep-power-in-suspend;
> +
> + vmmc-supply = <&vcc_sd>;
> + vqmmc-supply = <&vccio_sd>;
> + status = "okay";
> +};
> +
> +&uart2 {
> + status = "okay";
> +};
> +
> +&uart4 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&uart4_xfer>;
> +};
> +
> +&usb_host0_ehci {
> + status = "okay";
> +};
> +
> +&usb_otg {
> + status = "okay";
> +};
> +
> +&wdt {
> + status = "okay";
> +};
>
--
Best Regards
Shawn Lin
More information about the linux-arm-kernel
mailing list