[PATCH v2 19/22] usb: chipidea: msm: Handle phy power states
Peter Chen
hzpeterchen at gmail.com
Sun Jul 10 22:38:56 PDT 2016
On Thu, Jul 07, 2016 at 03:21:10PM -0700, Stephen Boyd wrote:
> The ULPI phy on qcom platforms needs to be initialized and
> powered on after a USB reset and before we toggle the run/stop
> bit. Otherwise, the phy locks up and doesn't work properly. Hook
> the phy initialization into the RESET event and the phy power off
> into the STOPPED event.
>
> Cc: Peter Chen <peter.chen at nxp.com>
> Cc: Greg Kroah-Hartman <gregkh at linuxfoundation.org>
> ---
> drivers/usb/chipidea/ci_hdrc_msm.c | 40 +++++++++++++++++++-------------------
> drivers/usb/chipidea/core.c | 8 ++++++--
> drivers/usb/chipidea/host.c | 8 ++++++--
> include/linux/usb/chipidea.h | 2 +-
> 4 files changed, 33 insertions(+), 25 deletions(-)
>
> diff --git a/drivers/usb/chipidea/ci_hdrc_msm.c b/drivers/usb/chipidea/ci_hdrc_msm.c
> index ab6a7713ee5c..5c486c15e043 100644
> --- a/drivers/usb/chipidea/ci_hdrc_msm.c
> +++ b/drivers/usb/chipidea/ci_hdrc_msm.c
> @@ -75,20 +75,33 @@ static const struct reset_control_ops ci_hdrc_msm_reset_ops = {
> .reset = ci_hdrc_msm_por_reset,
> };
>
> -static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> +static int ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> {
> struct device *dev = ci->dev->parent;
> struct ci_hdrc_msm *msm_ci = dev_get_drvdata(dev);
> + int ret;
>
> switch (event) {
> case CI_HDRC_CONTROLLER_RESET_EVENT:
> dev_dbg(dev, "CI_HDRC_CONTROLLER_RESET_EVENT received\n");
> +
> + hw_phymode_configure(ci);
> if (msm_ci->secondary_phy) {
> u32 val = readl_relaxed(msm_ci->base + HS_PHY_SEC_CTRL);
> val |= HS_PHY_DIG_CLAMP_N;
> writel_relaxed(val, msm_ci->base + HS_PHY_SEC_CTRL);
> }
>
> + ret = phy_init(ci->phy);
> + if (ret)
> + return ret;
> +
> + ret = phy_power_on(ci->phy);
> + if (ret) {
> + phy_exit(ci->phy);
> + return ret;
> + }
> +
> /* use AHB transactor, allow posted data writes */
> hw_write_id_reg(ci, HS_PHY_AHB_MODE, 0xffffffff, 0x8);
>
> @@ -108,21 +121,18 @@ static void ci_hdrc_msm_notify_event(struct ci_hdrc *ci, unsigned event)
> HSPHY_SESS_VLD_CTRL);
>
> }
> -
> - usb_phy_init(ci->usb_phy);
> break;
> case CI_HDRC_CONTROLLER_STOPPED_EVENT:
> dev_dbg(dev, "CI_HDRC_CONTROLLER_STOPPED_EVENT received\n");
> - /*
> - * Put the phy in non-driving mode. Otherwise host
> - * may not detect soft-disconnection.
> - */
> - usb_phy_notify_disconnect(ci->usb_phy, USB_SPEED_UNKNOWN);
> + phy_power_off(ci->phy);
> + phy_exit(ci->phy);
> break;
> default:
> dev_dbg(dev, "unknown ci_hdrc event\n");
> break;
> }
> +
> + return 0;
> }
>
> static int ci_hdrc_msm_mux_phy(struct ci_hdrc_msm *ci,
> @@ -162,7 +172,6 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
> {
> struct ci_hdrc_msm *ci;
> struct platform_device *plat_ci;
> - struct usb_phy *phy;
> struct clk *clk;
> struct reset_control *reset;
> struct resource *res;
> @@ -176,21 +185,12 @@ static int ci_hdrc_msm_probe(struct platform_device *pdev)
> return -ENOMEM;
> platform_set_drvdata(pdev, ci);
>
> - /*
> - * OTG(PHY) driver takes care of PHY initialization, clock management,
> - * powering up VBUS, mapping of registers address space and power
> - * management.
> - */
> - phy = devm_usb_get_phy_by_phandle(&pdev->dev, "usb-phy", 0);
> - if (IS_ERR(phy))
> - return PTR_ERR(phy);
> -
> ci->pdata.name = "ci_hdrc_msm";
> ci->pdata.capoffset = DEF_CAPOFFSET;
> ci->pdata.flags = CI_HDRC_REGS_SHARED | CI_HDRC_DISABLE_STREAMING |
> - CI_HDRC_OVERRIDE_AHB_BURST;
> + CI_HDRC_OVERRIDE_AHB_BURST |
> + CI_HDRC_OVERRIDE_PHY_CONTROL;
> ci->pdata.notify_event = ci_hdrc_msm_notify_event;
> - ci->pdata.usb_phy = phy;
>
> reset = devm_reset_control_get(&pdev->dev, "core");
> if (IS_ERR(reset))
> diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
> index f144e1bbcc82..0866c03d66df 100644
> --- a/drivers/usb/chipidea/core.c
> +++ b/drivers/usb/chipidea/core.c
> @@ -327,6 +327,7 @@ void hw_phymode_configure(struct ci_hdrc *ci)
> hw_write(ci, OP_PORTSC, PORTSC_STS, PORTSC_STS);
> }
> }
> +EXPORT_SYMBOL_GPL(hw_phymode_configure);
>
> /**
> * _ci_usb_phy_init: initialize phy taking in account both phy and usb_phy
> @@ -503,9 +504,12 @@ int hw_device_reset(struct ci_hdrc *ci)
> return ret;
> }
>
> - if (ci->platdata->notify_event)
> - ci->platdata->notify_event(ci,
> + if (ci->platdata->notify_event) {
> + ret = ci->platdata->notify_event(ci,
> CI_HDRC_CONTROLLER_RESET_EVENT);
> + if (ret)
> + return ret;
> + }
>
> /* USBMODE should be configured step by step */
> hw_write(ci, OP_USBMODE, USBMODE_CM, USBMODE_CM_IDLE);
> diff --git a/drivers/usb/chipidea/host.c b/drivers/usb/chipidea/host.c
> index a1d8551ca79d..844be1d02d38 100644
> --- a/drivers/usb/chipidea/host.c
> +++ b/drivers/usb/chipidea/host.c
> @@ -87,8 +87,12 @@ static int ehci_ci_reset(struct usb_hcd *hcd)
> if (ret)
> return ret;
>
> - if (ci->platdata->notify_event)
> - ci->platdata->notify_event(ci, CI_HDRC_CONTROLLER_RESET_EVENT);
> + if (ci->platdata->notify_event) {
> + ret = ci->platdata->notify_event(ci,
> + CI_HDRC_CONTROLLER_RESET_EVENT);
> + if (ret)
> + return ret;
> + }
>
> ci_platform_configure(ci);
>
> diff --git a/include/linux/usb/chipidea.h b/include/linux/usb/chipidea.h
> index d07b162073f7..5e76552c81e9 100644
> --- a/include/linux/usb/chipidea.h
> +++ b/include/linux/usb/chipidea.h
> @@ -61,7 +61,7 @@ struct ci_hdrc_platform_data {
> enum usb_dr_mode dr_mode;
> #define CI_HDRC_CONTROLLER_RESET_EVENT 0
> #define CI_HDRC_CONTROLLER_STOPPED_EVENT 1
> - void (*notify_event) (struct ci_hdrc *ci, unsigned event);
> + int (*notify_event) (struct ci_hdrc *ci, unsigned event);
> struct regulator *reg_vbus;
> struct usb_otg_caps ci_otg_caps;
> bool tpl_support;
> --
Acked-by: Peter Chen <peter.chen at nxp.com>
--
Best Regards,
Peter Chen
More information about the linux-arm-kernel
mailing list