[PATCH 5/9] ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs
Chen-Yu Tsai
wens at csie.org
Wed Jul 6 02:10:46 PDT 2016
The bananapi-m1-plus dts file was indented using 4 spaces, without
tabs. This does not match the code style.
Reindent the whole file before we do anything else.
Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts | 272 +++++++++++------------
1 file changed, 136 insertions(+), 136 deletions(-)
diff --git a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
index 89e38e9e0be6..edfb5b37939e 100644
--- a/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
+++ b/arch/arm/boot/dts/sun7i-a20-bananapi-m1-plus.dts
@@ -49,182 +49,182 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
/ {
- model = "Banana Pi BPI-M1-Plus";
- compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&led_pins_bananapi>;
-
- green {
- label = "bananapi-m1-plus:green:usr";
- gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
- };
-
- red {
- label = "bananapi-m1-plus:red:usr";
- gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "default-on";
- };
-
- };
-
- mmc3_pwrseq: mmc3_pwrseq {
- compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pwrseq_pin_bananapim1plus>;
- reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
- };
-
- reg_gmac_3v3: gmac-3v3 {
- compatible = "regulator-fixed";
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_power_pin_bananapi>;
- regulator-name = "gmac-3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- startup-delay-us = <100000>;
- enable-active-high;
- gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
- };
+ model = "Banana Pi BPI-M1-Plus";
+ compatible = "sinovoip,bpi-m1-plus", "allwinner,sun7i-a20";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_pins_bananapi>;
+
+ green {
+ label = "bananapi-m1-plus:green:usr";
+ gpios = <&pio 7 24 GPIO_ACTIVE_HIGH>;
+ };
+
+ red {
+ label = "bananapi-m1-plus:red:usr";
+ gpios = <&pio 7 25 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "default-on";
+ };
+
+ };
+
+ mmc3_pwrseq: mmc3_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pwrseq_pin_bananapim1plus>;
+ reset-gpios = <&pio 7 22 GPIO_ACTIVE_LOW>; /* PH22 WL-PMU-EN */
+ };
+
+ reg_gmac_3v3: gmac-3v3 {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_power_pin_bananapi>;
+ regulator-name = "gmac-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <100000>;
+ enable-active-high;
+ gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>;
+ };
};
&ahci {
- status = "okay";
+ status = "okay";
};
&codec {
- status = "okay";
+ status = "okay";
};
&ehci0 {
- status = "okay";
+ status = "okay";
};
&ehci1 {
- status = "okay";
+ status = "okay";
};
&gmac {
- pinctrl-names = "default";
- pinctrl-0 = <&gmac_pins_rgmii_a>;
- phy = <&phy1>;
- phy-mode = "rgmii";
- phy-supply = <®_gmac_3v3>;
- status = "okay";
-
- phy1: ethernet-phy at 1 {
- reg = <1>;
- };
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac_pins_rgmii_a>;
+ phy = <&phy1>;
+ phy-mode = "rgmii";
+ phy-supply = <®_gmac_3v3>;
+ status = "okay";
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
};
&i2c0 {
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins_a>;
- status = "okay";
-
- axp209: pmic at 34 {
- compatible = "x-powers,axp209";
- reg = <0x34>;
- interrupt-parent = <&nmi_intc>;
- interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
-
- interrupt-controller;
- #interrupt-cells = <1>;
- };
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins_a>;
+ status = "okay";
+
+ axp209: pmic at 34 {
+ compatible = "x-powers,axp209";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
};
&ir0 {
- pinctrl-names = "default";
- pinctrl-0 = <&ir0_rx_pins_a>;
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir0_rx_pins_a>;
+ status = "okay";
};
&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
- vmmc-supply = <®_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
- cd-inverted;
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_bananapi>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
+ cd-inverted;
+ status = "okay";
};
&mmc3 {
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-names = "default";
- pinctrl-0 = <&mmc3_pins_a>;
- vmmc-supply = <®_vcc3v3>;
- mmc-pwrseq = <&mmc3_pwrseq>;
- bus-width = <4>;
- non-removable;
- enable-sdio-wakeup;
- status = "okay";
-
- brcmf: bcrmf at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- interrupt-parent = <&pio>;
- interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
- interrupt-names = "host-wake";
- };
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc3_pins_a>;
+ vmmc-supply = <®_vcc3v3>;
+ mmc-pwrseq = <&mmc3_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ enable-sdio-wakeup;
+ status = "okay";
+
+ brcmf: bcrmf at 1 {
+ reg = <1>;
+ compatible = "brcm,bcm4329-fmac";
+ interrupt-parent = <&pio>;
+ interrupts = <7 15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-names = "host-wake";
+ };
};
&mmc3_pins_a {
- /* AP6210 requires pull-up */
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ /* AP6210 requires pull-up */
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
&ohci0 {
- status = "okay";
+ status = "okay";
};
&ohci1 {
- status = "okay";
+ status = "okay";
};
&pio {
- gmac_power_pin_bananapi: gmac_power_pin at 0 {
- allwinner,pins = "PH23";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- led_pins_bananapi: led_pins at 0 {
- allwinner,pins = "PH24", "PG2";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-
- mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 {
- allwinner,pins = "PH10";
- allwinner,function = "gpio_in";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
- };
-
- mmc3_pwrseq_pin_bananapim1plus: mmc3_pwrseq_pin at 0 {
- allwinner,pins = "PH22";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
+ gmac_power_pin_bananapi: gmac_power_pin at 0 {
+ allwinner,pins = "PH23";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ led_pins_bananapi: led_pins at 0 {
+ allwinner,pins = "PH24", "PG2";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ mmc0_cd_pin_bananapi: mmc0_cd_pin at 0 {
+ allwinner,pins = "PH10";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
+ };
+
+ mmc3_pwrseq_pin_bananapim1plus: mmc3_pwrseq_pin at 0 {
+ allwinner,pins = "PH22";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
};
&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
};
--
2.8.1
More information about the linux-arm-kernel
mailing list