[PATCH v8 2/2] drm/bridge: Add I2C based driver for ps8640 bridge
Jitao Shi
jitao.shi at mediatek.com
Sun Jan 31 20:13:32 PST 2016
This patch adds drm_bridge driver for parade DSI to eDP bridge chip.
Signed-off-by: Jitao Shi <jitao.shi at mediatek.com>
---
Changes since v7:
- Change ps8640_regw to ps8640_regw_bytes and remove devm_kzalloc
- Fine tune ps8640 power squence
- Add ps8640_pre_enable and ps8640_post_disable in ps8640_get_modes
- Remove unnecessary codes and comments
The following patches are needed to support dsi host through none dsi bus:
https://patchwork.kernel.org/patch/7818431/ ("drm/dsi: check for CONFIG_OF when defining of_mipi_dsi_device_add")
https://patchwork.kernel.org/patch/7818471/ ("drm/dsi: Refactor device creation")
https://patchwork.kernel.org/patch/7818501/ ("drm/dsi: Try to match non-DT dsi devices")
https://patchwork.kernel.org/patch/7818531/ ("drm/dsi: Check for used channels")
https://patchwork.kernel.org/patch/7818561/ ("drm/dsi: Add routine to unregister dsi device")
https://patchwork.kernel.org/patch/7818541/ ("drm/dsi: Get DSI host by DT device node")
---
drivers/gpu/drm/bridge/Kconfig | 10 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/parade-ps8640.c | 1084 ++++++++++++++++++++++++++++++++
3 files changed, 1095 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/parade-ps8640.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index 27e2022..fe8ad50 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -40,4 +40,14 @@ config DRM_PARADE_PS8622
---help---
Parade eDP-LVDS bridge chip driver.
+config DRM_PARADE_PS8640
+ tristate "Parade PS8640 MIPI DSI to eDP Converter"
+ depends on OF && I2C
+ select DRM_KMS_HELPER
+ select DRM_PANEL
+ ---help---
+ Choose this option if you have PS8640 for display
+ The PS8640 is a high-performance and low-power
+ MIPI DSI to eDP converter
+
endmenu
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index f13c33d..fbe38dc 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -4,3 +4,4 @@ obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
+obj-$(CONFIG_DRM_PARADE_PS8640) += parade-ps8640.o
diff --git a/drivers/gpu/drm/bridge/parade-ps8640.c b/drivers/gpu/drm/bridge/parade-ps8640.c
new file mode 100644
index 0000000..0230ab5
--- /dev/null
+++ b/drivers/gpu/drm/bridge/parade-ps8640.c
@@ -0,0 +1,1084 @@
+/*
+ * Copyright (c) 2014 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/firmware.h>
+#include <linux/gpio.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_gpio.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+#include <asm/unaligned.h>
+#include <drm/drm_panel.h>
+
+#include <drmP.h>
+#include <drm_atomic_helper.h>
+#include <drm_crtc_helper.h>
+#include <drm_crtc.h>
+#include <drm_mipi_dsi.h>
+
+#define PAGE2_SPI_CFG3 0x82
+#define I2C_TO_SPI_RESET 0x20
+#define PAGE2_ROMADD_BYTE1 0x8e
+#define PAGE2_ROMADD_BYTE2 0x8f
+#define PAGE2_SWSPI_WDATA 0x90
+#define PAGE2_SWSPI_RDATA 0x91
+#define PAGE2_SWSPI_LEN 0x92
+#define PAGE2_SWSPI_CTL 0x93
+#define TRIGGER_NO_READBACK 0x05
+#define TRIGGER_READBACK 0x01
+#define PAGE2_SPI_STATUS 0x9e
+#define PAGE2_GPIO_L 0xa6
+#define PAGE2_GPIO_H 0xa7
+#define PS_GPIO9 BIT(1)
+#define PAGE2_IROM_CTRL 0xb0
+#define IROM_ENABLE 0xc0
+#define IROM_DISABLE 0x80
+#define PAGE2_SW_REST 0xbc
+#define PAGE2_ENCTLSPI_WR 0xda
+#define PAGE2_I2C_BYPASS 0xea
+#define I2C_BYPASS_EN 0xd0
+
+#define PAGE3_SET_ADD 0xfe
+#define PAGE3_SET_VAL 0xff
+#define VDO_CTL_ADD 0x13
+#define VDO_DIS 0x18
+#define VDO_EN 0x1c
+
+#define PAGE4_REV_L 0xf0
+#define PAGE4_REV_H 0xf1
+#define PAGE4_CHIP_L 0xf2
+#define PAGE4_CHIP_H 0xf3
+
+/* Firmware */
+#define SPI_MAX_RETRY_CNT 8
+#define PS_FW_NAME "ps864x_fw.bin"
+
+#define FW_CHIP_ID_OFFSET 0
+#define FW_VERSION_OFFSET 2
+
+#define bridge_to_ps8640(e) container_of(e, struct ps8640, bridge)
+#define connector_to_ps8640(e) container_of(e, struct ps8640, connector)
+
+struct ps8640_info {
+ u8 family_id;
+ u8 variant_id;
+ u16 version;
+};
+
+struct ps8640 {
+ struct drm_connector connector;
+ struct drm_bridge bridge;
+ struct mipi_dsi_device *dsi;
+ struct i2c_client *page[8];
+ struct ps8640_driver_data *driver_data;
+ struct regulator *pwr_1v2_supply;
+ struct regulator *pwr_3v3_supply;
+ struct drm_panel *panel;
+ struct gpio_desc *gpio_rst_n;
+ struct gpio_desc *gpio_slp_n;
+ struct gpio_desc *gpio_mode_sel_n;
+ bool enabled;
+
+ /* firmware file name */
+ bool in_fw_update;
+ char *fw_file;
+ struct ps8640_info info;
+};
+
+static const u8 enc_ctrl_code[6] = {0xaa, 0x55, 0x50, 0x41, 0x52, 0x44};
+
+static int ps8640_regr(struct i2c_client *client, u8 reg, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct i2c_msg msgs[] = {
+ {
+ .addr = client->addr,
+ .flags = 0,
+ .len = 1,
+ .buf = ®,
+ },
+ {
+ .addr = client->addr,
+ .flags = I2C_M_RD,
+ .len = data_len,
+ .buf = data,
+ }
+ };
+
+ ret = i2c_transfer(client->adapter, msgs, 2);
+
+ if (ret == 2)
+ return 0;
+ if (ret < 0)
+ return ret;
+ else
+ return -EIO;
+}
+
+static int ps8640_regw_bytes(struct i2c_client *client, u8 *data,
+ u16 data_len)
+{
+ int ret;
+ struct i2c_msg msg;
+
+ msg.addr = client->addr;
+ msg.flags = 0;
+ msg.len = data_len;
+ msg.buf = data;
+
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ if (ret == 1)
+ return 0;
+ if (ret < 0)
+ return ret;
+ else
+ return -EIO;
+}
+
+static int ps8640_regw_byte(struct i2c_client *client, u8 reg, u8 data)
+{
+ int ret;
+ struct i2c_msg msg;
+ u8 buf[] = {reg, data};
+
+ msg.addr = client->addr;
+ msg.flags = 0;
+ msg.len = sizeof(buf);
+ msg.buf = buf;
+
+ ret = i2c_transfer(client->adapter, &msg, 1);
+ if (ret == 1)
+ return 0;
+ if (ret < 0)
+ return ret;
+ else
+ return -EIO;
+}
+
+static void ps8640_get_mcu_fw_version(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[5];
+ u8 fw_ver[2];
+
+ ps8640_regr(client, 0x4, fw_ver, 2);
+ ps_bridge->info.version = (fw_ver[0] << 8) | fw_ver[1];
+
+ DRM_INFO_ONCE("ps8640 rom fw version %d.%d\n", fw_ver[0], fw_ver[1]);
+}
+
+static int ps8640_bridge_enable(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[3];
+ int ret;
+ u8 vdo_ctrl_buf[3] = {PAGE3_SET_ADD, VDO_CTL_ADD, VDO_EN};
+
+ ret = ps8640_regw_bytes(client, vdo_ctrl_buf, 3);
+ return ret;
+}
+
+static void ps8640_pre_enable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ struct i2c_client *client = ps_bridge->page[2];
+ int err, retry_cnt = 0;
+ u8 set_vdo_done;
+
+ if (ps_bridge->in_fw_update)
+ return;
+
+ if (ps_bridge->enabled)
+ return;
+
+ err = drm_panel_prepare(ps_bridge->panel);
+ if (err < 0) {
+ DRM_ERROR("failed to prepare panel: %d\n", err);
+ return;
+ }
+
+ gpiod_set_value(ps_bridge->gpio_slp_n, 1);
+ gpiod_set_value(ps_bridge->gpio_rst_n, 0);
+
+ err = regulator_enable(ps_bridge->pwr_1v2_supply);
+ if (err < 0) {
+ DRM_ERROR("failed to enable vdd12-supply: %d\n", err);
+ goto err_panel_unprepare;
+ }
+
+ err = regulator_enable(ps_bridge->pwr_3v3_supply);
+ if (err < 0) {
+ DRM_ERROR("failed to enable vdd33-supply: %d\n", err);
+ goto err_regulator_1v2_disable;
+ }
+
+ usleep_range(500, 700);
+ gpiod_set_value(ps_bridge->gpio_rst_n, 1);
+
+ /*
+ * Wait for the ps8640 embed mcu ready
+ * First wait 200ms and then check the mcu ready flag every 20ms
+ */
+ msleep(200);
+ do {
+ err = ps8640_regr(client, PAGE2_GPIO_H, &set_vdo_done, 1);
+ if (err < 0) {
+ DRM_ERROR("failed read PAGE2_GPIO_H: %d\n", err);
+ goto err_regulator_1v2_disable;
+ }
+ msleep(20);
+ } while ((retry_cnt++ < 10) && ((set_vdo_done & PS_GPIO9) != PS_GPIO9));
+
+ if (ps_bridge->info.version == 0)
+ ps8640_get_mcu_fw_version(ps_bridge);
+ /* Switch access edp panel's edid through i2c */
+ ps8640_regw_byte(client, PAGE2_I2C_BYPASS, I2C_BYPASS_EN);
+ ps_bridge->enabled = true;
+
+ return;
+
+err_regulator_1v2_disable:
+ regulator_disable(ps_bridge->pwr_1v2_supply);
+err_panel_unprepare:
+ drm_panel_unprepare(ps_bridge->panel);
+}
+
+static void ps8640_enable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ int err;
+
+ err = ps8640_bridge_enable(ps_bridge);
+ if (err)
+ DRM_ERROR("failed to enable unmutevideo: %d\n", err);
+
+ err = drm_panel_enable(ps_bridge->panel);
+ if (err < 0)
+ DRM_ERROR("failed to enable panel: %d\n", err);
+}
+
+static void ps8640_disable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ int err;
+
+ err = drm_panel_disable(ps_bridge->panel);
+ if (err < 0)
+ DRM_ERROR("failed to disable panel: %d\n", err);
+}
+
+static void ps8640_post_disable(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ int err;
+
+ if (ps_bridge->in_fw_update)
+ return;
+
+ if (!ps_bridge->enabled)
+ return;
+
+ ps_bridge->enabled = false;
+
+ gpiod_set_value(ps_bridge->gpio_rst_n, 0);
+ gpiod_set_value(ps_bridge->gpio_slp_n, 0);
+ regulator_disable(ps_bridge->pwr_3v3_supply);
+ regulator_disable(ps_bridge->pwr_1v2_supply);
+
+ err = drm_panel_unprepare(ps_bridge->panel);
+ if (err)
+ DRM_ERROR("failed to unprepare panel: %d\n", err);
+}
+
+static int ps8640_get_modes(struct drm_connector *connector)
+{
+ struct ps8640 *ps_bridge = connector_to_ps8640(connector);
+ bool power_off;
+ int num_modes = 0;
+
+ power_off = !ps_bridge->enabled;
+ ps8640_pre_enable(&ps_bridge->bridge);
+
+ num_modes = drm_panel_get_modes(ps_bridge->panel);
+
+ if (power_off)
+ ps8640_post_disable(&ps_bridge->bridge);
+
+ return num_modes;
+}
+
+static struct drm_encoder *ps8640_best_encoder(struct drm_connector *connector)
+{
+ struct ps8640 *ps_bridge;
+
+ ps_bridge = connector_to_ps8640(connector);
+ return ps_bridge->bridge.encoder;
+}
+
+static const struct drm_connector_helper_funcs ps8640_connector_helper_funcs = {
+ .get_modes = ps8640_get_modes,
+ .best_encoder = ps8640_best_encoder,
+};
+
+static enum drm_connector_status ps8640_detect(struct drm_connector *connector,
+ bool force)
+{
+ return connector_status_connected;
+}
+
+static void ps8640_connector_destroy(struct drm_connector *connector)
+{
+ drm_connector_unregister(connector);
+ drm_connector_cleanup(connector);
+}
+
+static const struct drm_connector_funcs ps8640_connector_funcs = {
+ .dpms = drm_atomic_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = ps8640_detect,
+ .destroy = ps8640_connector_destroy,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+int ps8640_bridge_attach(struct drm_bridge *bridge)
+{
+ struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
+ struct device *dev = &ps_bridge->page[0]->dev;
+ struct device_node *np = dev->of_node;
+ struct device_node *port, *in_ep;
+ struct device_node *dsi_node = NULL;
+ struct mipi_dsi_host *host = ps_bridge->dsi->host;
+ int ret;
+
+ ret = drm_connector_init(bridge->dev, &ps_bridge->connector,
+ &ps8640_connector_funcs,
+ DRM_MODE_CONNECTOR_eDP);
+
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector with drm: %d\n", ret);
+ return ret;
+ }
+
+ drm_connector_helper_add(&ps_bridge->connector,
+ &ps8640_connector_helper_funcs);
+ drm_connector_register(&ps_bridge->connector);
+
+ ps_bridge->connector.dpms = DRM_MODE_DPMS_ON;
+ drm_mode_connector_attach_encoder(&ps_bridge->connector,
+ bridge->encoder);
+
+ if (ps_bridge->panel)
+ drm_panel_attach(ps_bridge->panel, &ps_bridge->connector);
+
+ /* port at 0 is ps8640 dsi input port */
+ port = of_graph_get_port_by_id(np, 0);
+ if (port) {
+ in_ep = of_get_child_by_name(port, "endpoint");
+ of_node_put(port);
+ if (in_ep) {
+ dsi_node = of_graph_get_remote_port_parent(in_ep);
+ of_node_put(in_ep);
+ }
+ }
+ if (dsi_node) {
+ host = of_find_mipi_dsi_host_by_node(dsi_node);
+ of_node_put(dsi_node);
+ if (!host)
+ return -ENODEV;
+ }
+
+ ps_bridge->dsi->host = host;
+ ps_bridge->dsi->mode_flags = MIPI_DSI_MODE_VIDEO |
+ MIPI_DSI_MODE_VIDEO_SYNC_PULSE;
+ ps_bridge->dsi->format = MIPI_DSI_FMT_RGB888;
+ ps_bridge->dsi->lanes = 4;
+ ret = mipi_dsi_attach(ps_bridge->dsi);
+ if (ret) {
+ drm_panel_detach(ps_bridge->panel);
+ return ret;
+ }
+
+ return ret;
+}
+
+static const struct drm_bridge_funcs ps8640_bridge_funcs = {
+ .attach = ps8640_bridge_attach,
+ .disable = ps8640_disable,
+ .post_disable = ps8640_post_disable,
+ .pre_enable = ps8640_pre_enable,
+ .enable = ps8640_enable,
+};
+
+static ssize_t ps8640_fw_file_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct ps8640 *ps_bridge = dev_get_drvdata(dev);
+
+ return scnprintf(buf, PAGE_SIZE, "%s\n", ps_bridge->fw_file);
+}
+
+static int ps8640_update_file_name(struct device *dev, char **file_name,
+ const char *buf, size_t count)
+{
+ char *new_file_name;
+
+ /* Simple sanity check */
+ if (count > 64) {
+ dev_warn(dev, "File name too long\n");
+ return -EINVAL;
+ }
+
+ new_file_name = devm_kmalloc(dev, count + 1, GFP_KERNEL);
+ if (!new_file_name)
+ return -ENOMEM;
+
+ memcpy(new_file_name, buf, count + 1);
+
+ /* Echo into the sysfs entry may append newline at the end of buf */
+ if (new_file_name[count - 1] == '\n')
+ count--;
+
+ new_file_name[count] = '\0';
+
+ if (*file_name)
+ devm_kfree(dev, *file_name);
+
+ *file_name = new_file_name;
+
+ return 0;
+}
+
+/* Firmware Version is returned as Major.Minor.Build */
+static ssize_t ps8640_fw_version_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct ps8640 *ps_bridge = dev_get_drvdata(dev);
+ struct ps8640_info *info = &ps_bridge->info;
+
+ return scnprintf(buf, PAGE_SIZE, "%u.%u\n", info->version >> 8,
+ info->version & 0xff);
+}
+
+/* Hardware Version is returned as FamilyID.VariantID */
+static ssize_t ps8640_hw_version_show(struct device *dev,
+ struct device_attribute *attr, char *buf)
+{
+ struct ps8640 *ps_bridge = dev_get_drvdata(dev);
+ struct ps8640_info *info = &ps_bridge->info;
+
+ return scnprintf(buf, PAGE_SIZE, "ps%u.%u\n", info->family_id,
+ info->variant_id);
+}
+
+static int ps8640_spi_send_cmd(struct ps8640 *ps_bridge, u8 *cmd, u8 cmd_len)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ u8 i;
+ int ret;
+
+ ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
+ if (ret)
+ goto err;
+
+ /* write command in write port */
+ for (i = 0; i < cmd_len; i++) {
+ ret = ps8640_regw_byte(client, PAGE2_SWSPI_WDATA, cmd[i]);
+ if (ret)
+ goto err;
+ }
+ /* command length */
+ ret = ps8640_regw_byte(client, PAGE2_SWSPI_LEN, cmd_len - 1);
+ if (ret)
+ goto err;
+ /* trigger read */
+ ret = ps8640_regw_byte(client, PAGE2_SWSPI_CTL, TRIGGER_NO_READBACK);
+ if (ret)
+ goto err;
+
+ ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
+ if (ret)
+ goto err;
+
+ return 0;
+
+err:
+ dev_err(&client->dev, "send command err: %d\n", ret);
+ return ret;
+}
+
+static int ps8640_wait_spi_ready(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ u8 spi_rdy_st, retry_cnt = 0;
+
+ do {
+ ps8640_regr(client, PAGE2_SPI_STATUS, &spi_rdy_st, 1);
+ msleep(20);
+ if ((retry_cnt == SPI_MAX_RETRY_CNT) &&
+ ((spi_rdy_st & 0x0c) != 0x0c)) {
+ dev_err(&client->dev, "wait spi ready timeout\n");
+ return -EBUSY;
+ }
+ } while ((retry_cnt++ < SPI_MAX_RETRY_CNT) &&
+ (spi_rdy_st & 0x0c) == 0x0c);
+
+ return 0;
+}
+
+static int ps8640_wait_spi_nobusy(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ u8 spi_status, retry_cnt = 0;
+ int ret;
+
+ do {
+ /* 0x05 RDSR; Read-Status-Register */
+ ret = ps8640_regw_byte(client, PAGE2_SWSPI_WDATA, 0x05);
+ if (ret)
+ goto err_send_cmd_exit;
+
+ /* command length */
+ ret = ps8640_regw_byte(client, PAGE2_SWSPI_LEN, 0x00);
+ if (ret)
+ goto err_send_cmd_exit;
+
+ /* trigger read */
+ ret = ps8640_regw_byte(client, PAGE2_SWSPI_CTL,
+ TRIGGER_READBACK);
+ if (ret)
+ goto err_send_cmd_exit;
+
+ /* delay for cmd send */
+ usleep_range(100, 300);
+ /* wait for SPI ROM until not busy */
+ ret = ps8640_regr(client, PAGE2_SWSPI_RDATA, &spi_status, 1);
+ if (ret)
+ goto err_send_cmd_exit;
+ } while ((retry_cnt++ < SPI_MAX_RETRY_CNT) &&
+ (spi_status & 0x0c) == 0x0c);
+
+ if ((retry_cnt > SPI_MAX_RETRY_CNT) && (spi_status & 0x0c) != 0x0c) {
+ ret = -EBUSY;
+ dev_err(&client->dev, "wait spi no busy timeout: %d\n", ret);
+ goto err_timeout;
+ }
+
+ return 0;
+
+err_send_cmd_exit:
+ dev_err(&client->dev, "send command err: %d\n", ret);
+
+err_timeout:
+ return ret;
+}
+
+static int ps8640_wait_rom_idle(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ int ret;
+
+ ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_wait_spi_ready(ps_bridge);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_wait_spi_nobusy(ps_bridge);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
+ if (ret)
+ goto exit;
+
+exit:
+ if (ret)
+ dev_err(&client->dev, "wait ps8640 rom idle fail: %d\n", ret);
+
+ return ret;
+}
+
+static int ps8640_spi_dl_mode(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ int ret;
+
+ /* switch ps8640 mode to spi dl mode */
+ gpiod_set_value(ps_bridge->gpio_mode_sel_n, 0);
+
+ /* reset spi interface */
+ ret = ps8640_regw_byte(client, PAGE2_SW_REST, 0xc0);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_regw_byte(client, PAGE2_SW_REST, 0x40);
+ if (ret)
+ goto exit;
+
+exit:
+ if (ret)
+ dev_err(&client->dev, "fail reset spi interface: %d\n", ret);
+
+ return ret;
+}
+
+static int ps8640_rom_prepare(struct ps8640 *ps_bridge)
+{
+ struct i2c_client *client = ps_bridge->page[2];
+ struct device *dev = &client->dev;
+ u8 i, cmd[2];
+ int ret;
+
+ /* Enable-Write-Status-Register */
+ cmd[0] = 0x06;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+ if (ret) {
+ dev_err(dev, "failed enable-write-status-register: %d\n", ret);
+ return ret;
+ }
+
+ /* disable all protection */
+ cmd[0] = 0x01;
+ cmd[1] = 0x00;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 2);
+ if (ret) {
+ dev_err(dev, "fail disable all protection: %d\n", ret);
+ return ret;
+ }
+
+ /* wait for SPI module ready */
+ ret = ps8640_wait_rom_idle(ps_bridge);
+ if (ret) {
+ dev_err(dev, "fail wait rom idle: %d\n", ret);
+ return ret;
+ }
+
+ ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_ENABLE);
+ for (i = 0; i < 6; i++)
+ ps8640_regw_byte(client, PAGE2_ENCTLSPI_WR, enc_ctrl_code[i]);
+ ps8640_regw_byte(client, PAGE2_IROM_CTRL, IROM_DISABLE);
+
+ /* Enable-Write-Status-Register */
+ cmd[0] = 0x06;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+ if (ret) {
+ dev_err(dev, "fail enable-write-status-register: %d\n", ret);
+ return ret;
+ }
+
+ /* chip erase command */
+ cmd[0] = 0xc7;
+ ret = ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+ if (ret) {
+ dev_err(dev, "fail disable all protection: %d\n", ret);
+ return ret;
+ }
+
+ ret = ps8640_wait_rom_idle(ps_bridge);
+ if (ret) {
+ dev_err(dev, "fail wait rom idle: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ps8640_validate_firmware(struct ps8640 *ps_bridge,
+ const struct firmware *fw)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ struct ps8640_info *info = &ps_bridge->info;
+ u16 fw_chip_id, fw_version_id;
+
+ /*
+ * Get the chip_id from the firmware. Make sure that it is the
+ * right controller to do the firmware and config update.
+ */
+ fw_chip_id = get_unaligned_le16(fw->data + FW_CHIP_ID_OFFSET);
+
+ if (fw_chip_id != 0x8640) {
+ dev_err(&client->dev,
+ "chip id mismatch: fw 0x%x vs. chip 0x8640\n",
+ fw_chip_id);
+ return -ENODEV;
+ }
+
+ fw_version_id = get_unaligned_le16(fw->data + FW_VERSION_OFFSET);
+
+ if (fw_chip_id != info->version) {
+ dev_err(&client->dev,
+ "fw version mismatch: fw %d.%d vs. chip %d.%d\n",
+ fw_version_id >> 8, fw_version_id & 0xff,
+ info->version >> 8, info->version & 0xff);
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
+static int ps8640_write_rom(struct ps8640 *ps_bridge, const struct firmware *fw)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ struct device *dev = &client->dev;
+ struct i2c_client *client2 = ps_bridge->page[2];
+ struct i2c_client *client7 = ps_bridge->page[7];
+ unsigned int pos = 0;
+ u8 buf[257], rom_page_id_buf[3];
+ int ret;
+ u16 cpy_len;
+
+ ps8640_regw_byte(client2, PAGE2_SPI_CFG3, I2C_TO_SPI_RESET);
+ msleep(100);
+ ps8640_regw_byte(client2, PAGE2_SPI_CFG3, 0x00);
+
+ while (pos < fw->size) {
+ rom_page_id_buf[0] = PAGE2_ROMADD_BYTE1;
+ rom_page_id_buf[1] = (pos >> 8) & 0xff;
+ rom_page_id_buf[2] = (pos >> 16) & 0xff;
+ ret = ps8640_regw_bytes(client2, rom_page_id_buf, 3);
+ if (ret)
+ goto error;
+ cpy_len = fw->size >= 256 + pos ? 256 : fw->size - pos;
+ buf[0] = 0;
+ memcpy(buf + 1, fw->data + pos, cpy_len);
+ ret = ps8640_regw_bytes(client7, buf, cpy_len + 1);
+ if (ret)
+ goto error;
+
+ pos += cpy_len;
+
+ dev_dbg(dev, "fw update completed %u / %zu bytes\n", pos,
+ fw->size);
+ }
+ return 0;
+
+error:
+ dev_err(dev, "failed write extenal flash, %d\n", ret);
+ return ret;
+}
+
+static int ps8640_spi_normal_mode(struct ps8640 *ps_bridge)
+{
+ u8 cmd[2];
+ struct i2c_client *client = ps_bridge->page[2];
+
+ /* Enable-Write-Status-Register */
+ cmd[0] = 0x06;
+ ps8640_spi_send_cmd(ps_bridge, cmd, 1);
+
+ /* protect BPL/BP0/BP1 */
+ cmd[0] = 0x01;
+ cmd[1] = 0x8c;
+ ps8640_spi_send_cmd(ps_bridge, cmd, 2);
+
+ /* wait for SPI rom ready */
+ ps8640_wait_rom_idle(ps_bridge);
+
+ /* disable PS8640 mapping function */
+ ps8640_regw_byte(client, PAGE2_ENCTLSPI_WR, 0x00);
+
+ gpiod_set_value(ps_bridge->gpio_mode_sel_n, 1);
+ return 0;
+}
+
+static int ps8640_enter_bl(struct ps8640 *ps_bridge)
+{
+ int ret;
+
+ ret = ps8640_spi_dl_mode(ps_bridge);
+ if (ret)
+ return ret;
+
+ ps_bridge->in_fw_update = true;
+ return 0;
+}
+
+static void ps8640_exit_bl(struct ps8640 *ps_bridge, const struct firmware *fw)
+{
+ ps_bridge->in_fw_update = false;
+ ps8640_spi_normal_mode(ps_bridge);
+}
+
+static int ps8640_load_fw(struct ps8640 *ps_bridge, const struct firmware *fw)
+{
+ struct i2c_client *client = ps_bridge->page[0];
+ struct device *dev = &client->dev;
+ int ret;
+ bool ps8640_status_backup = ps_bridge->enabled;
+
+ if (!ps_bridge->in_fw_update) {
+ if (!ps8640_status_backup)
+ ps8640_pre_enable(&ps_bridge->bridge);
+
+ ret = ps8640_enter_bl(ps_bridge);
+ if (ret)
+ goto exit;
+ }
+
+ ret = ps8640_validate_firmware(ps_bridge, fw);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_rom_prepare(ps_bridge);
+ if (ret)
+ goto exit;
+
+ ret = ps8640_write_rom(ps_bridge, fw);
+
+exit:
+ if (ret)
+ dev_err(dev, "Failed to load firmware, %d\n", ret);
+
+ ps8640_exit_bl(ps_bridge, fw);
+ if (!ps8640_status_backup)
+ ps8640_post_disable(&ps_bridge->bridge);
+ return ret;
+}
+
+static ssize_t ps8640_update_fw_store(struct device *dev,
+ struct device_attribute *attr,
+ const char *buf, size_t count)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct ps8640 *ps_bridge = i2c_get_clientdata(client);
+ const struct firmware *fw;
+ int error;
+
+ error = request_firmware(&fw, ps_bridge->fw_file, dev);
+ if (error) {
+ dev_err(dev, "Unable to open firmware %s: %d\n",
+ ps_bridge->fw_file, error);
+ return error;
+ }
+
+ error = ps8640_load_fw(ps_bridge, fw);
+ if (error)
+ dev_err(dev, "The firmware update failed(%d)\n", error);
+ else
+ dev_info(dev, "The firmware update succeeded\n");
+
+ release_firmware(fw);
+ return error ? error : count;
+}
+
+static DEVICE_ATTR(fw_file, S_IRUGO, ps8640_fw_file_show, NULL);
+static DEVICE_ATTR(fw_version, S_IRUGO, ps8640_fw_version_show, NULL);
+static DEVICE_ATTR(hw_version, S_IRUGO, ps8640_hw_version_show, NULL);
+static DEVICE_ATTR(update_fw, S_IWUSR, NULL, ps8640_update_fw_store);
+
+static struct attribute *ps8640_attrs[] = {
+ &dev_attr_fw_file.attr,
+ &dev_attr_fw_version.attr,
+ &dev_attr_hw_version.attr,
+ &dev_attr_update_fw.attr,
+ NULL
+};
+
+static const struct attribute_group ps8640_attr_group = {
+ .attrs = ps8640_attrs,
+};
+
+static void ps8640_remove_sysfs_group(void *data)
+{
+ struct ps8640 *ps_bridge = data;
+
+ sysfs_remove_group(&ps_bridge->page[0]->dev.kobj, &ps8640_attr_group);
+}
+
+static int ps8640_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &client->dev;
+ struct ps8640 *ps_bridge;
+ struct device_node *np = dev->of_node;
+ struct device_node *port, *out_ep;
+ struct device_node *panel_node = NULL;
+ int i, ret;
+
+ ps_bridge = devm_kzalloc(dev, sizeof(*ps_bridge), GFP_KERNEL);
+ ps_bridge->dsi = devm_kzalloc(dev, sizeof(struct mipi_dsi_device),
+ GFP_KERNEL);
+ if (!ps_bridge) {
+ ret = -ENOMEM;
+ goto exit;
+ }
+ /* port at 1 is ps8640 output port */
+ port = of_graph_get_port_by_id(np, 1);
+ if (port) {
+ out_ep = of_get_child_by_name(port, "endpoint");
+ of_node_put(port);
+ if (out_ep) {
+ panel_node = of_graph_get_remote_port_parent(out_ep);
+ of_node_put(out_ep);
+ }
+ }
+ if (panel_node) {
+ ps_bridge->panel = of_drm_find_panel(panel_node);
+ of_node_put(panel_node);
+ if (!ps_bridge->panel) {
+ ret = -EPROBE_DEFER;
+ goto exit;
+ }
+ }
+
+ ps_bridge->pwr_3v3_supply = devm_regulator_get(dev, "vdd33");
+ if (IS_ERR(ps_bridge->pwr_3v3_supply)) {
+ ret = PTR_ERR(ps_bridge->pwr_3v3_supply);
+ dev_err(dev, "cannot get vdd33 supply: %d\n", ret);
+ goto exit;
+ }
+
+ ps_bridge->pwr_1v2_supply = devm_regulator_get(dev, "vdd12");
+ if (IS_ERR(ps_bridge->pwr_1v2_supply)) {
+ ret = PTR_ERR(ps_bridge->pwr_1v2_supply);
+ dev_err(dev, "cannot get vdd12 supply: %d\n", ret);
+ goto exit;
+ }
+
+ ps_bridge->gpio_mode_sel_n = devm_gpiod_get(&client->dev, "mode-sel",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ps_bridge->gpio_mode_sel_n)) {
+ ret = PTR_ERR(ps_bridge->gpio_mode_sel_n);
+ dev_err(dev, "cannot get gpio_mode_sel_n %d\n", ret);
+ goto exit;
+ }
+
+ ps_bridge->gpio_slp_n = devm_gpiod_get(&client->dev, "sleep",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ps_bridge->gpio_slp_n)) {
+ ret = PTR_ERR(ps_bridge->gpio_slp_n);
+ dev_err(dev, "cannot get gpio_slp_n: %d\n", ret);
+ goto exit;
+ }
+
+ ps_bridge->gpio_rst_n = devm_gpiod_get(&client->dev, "reset",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(ps_bridge->gpio_rst_n)) {
+ ret = PTR_ERR(ps_bridge->gpio_rst_n);
+ dev_err(dev, "cannot get gpio_rst_n: %d\n", ret);
+ goto exit;
+ }
+
+ ps_bridge->bridge.funcs = &ps8640_bridge_funcs;
+ ps_bridge->bridge.of_node = dev->of_node;
+ ret = drm_bridge_add(&ps_bridge->bridge);
+ if (ret) {
+ dev_err(dev, "Failed to add bridge: %d\n", ret);
+ goto exit;
+ }
+
+ ret = ps8640_update_file_name(&client->dev, &ps_bridge->fw_file,
+ PS_FW_NAME, strlen(PS_FW_NAME));
+ if (ret) {
+ dev_err(dev, "failed to update file name: %d\n", ret);
+ goto exit_drm_bridge_remove;
+ }
+
+ ps_bridge->page[0] = client;
+
+ /*
+ * ps8640 uses multiple addresses, use dummy devices for them
+ * page[0]: for DP control
+ * page[1]: for VIDEO Bridge
+ * page[2]: for control top
+ * page[3]: for DSI Link Control1
+ * page[4]: for MIPI Phy
+ * page[5]: for VPLL
+ * page[6]: for DSI Link Control2
+ * page[7]: for spi rom mapping
+ */
+ for (i = 1; i < 8; i++) {
+ ps_bridge->page[i] = i2c_new_dummy(client->adapter,
+ client->addr + i);
+ if (!ps_bridge->page[i]) {
+ dev_err(dev, "failed i2c dummy device, address%02x\n",
+ client->addr + i);
+ ret = -EBUSY;
+ goto exit_dummy;
+ }
+ }
+ i2c_set_clientdata(client, ps_bridge);
+
+ ret = sysfs_create_group(&client->dev.kobj, &ps8640_attr_group);
+ if (ret) {
+ dev_err(dev, "failed to create sysfs entries: %d\n", ret);
+ goto exit_dummy;
+ }
+
+ ret = devm_add_action(dev, ps8640_remove_sysfs_group, ps_bridge);
+ if (ret) {
+ dev_err(dev, "failed to add sysfs cleanup action: %d\n", ret);
+ goto exit_remove_sysfs;
+ }
+ return 0;
+
+exit_remove_sysfs:
+ sysfs_remove_group(&ps_bridge->page[0]->dev.kobj, &ps8640_attr_group);
+exit_dummy:
+ for (i = 1; i < 8; i++)
+ if (ps_bridge->page[i])
+ i2c_unregister_device(ps_bridge->page[i]);
+exit_drm_bridge_remove:
+ drm_bridge_remove(&ps_bridge->bridge);
+exit:
+ return ret;
+}
+
+static int ps8640_remove(struct i2c_client *client)
+{
+ struct ps8640 *ps_bridge = i2c_get_clientdata(client);
+ int i;
+
+ for (i = 1; i < 8; i++)
+ i2c_unregister_device(ps_bridge->page[i]);
+
+ drm_bridge_remove(&ps_bridge->bridge);
+
+ return 0;
+}
+
+static const struct i2c_device_id ps8640_i2c_table[] = {
+ {"parade,ps8640", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ps8640_i2c_table);
+
+static const struct of_device_id ps8640_match[] = {
+ { .compatible = "parade,ps8640" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ps8640_match);
+
+static struct i2c_driver ps8640_driver = {
+ .id_table = ps8640_i2c_table,
+ .probe = ps8640_probe,
+ .remove = ps8640_remove,
+ .driver = {
+ .name = "parade,ps8640",
+ .of_match_table = ps8640_match,
+ },
+};
+module_i2c_driver(ps8640_driver);
+
+MODULE_AUTHOR("Jitao Shi <jitao.shi at mediatek.com>");
+MODULE_AUTHOR("CK Hu <ck.hu at mediatek.com>");
+MODULE_DESCRIPTION("PARADE ps8640 DSI-eDP converter driver");
+MODULE_LICENSE("GPL v2");
--
1.7.9.5
More information about the linux-arm-kernel
mailing list