[PATCH] serial: imx: fix dcd interrupt firing during probe

[Peter Hurley]

On 01/25/2016 09:50 AM, Stefan Agner wrote:
> Hi Marcel,
> 
> [also added Lucas]
> 
> On 2015-12-30 19:12, Marcel Ziswiler wrote:
>> Continuing on the Apalis iMX6 mainlining work started by Petr Štetiar I
>> noticed that it only boots when rebooting from NXP's downstream 3.14.28
>> kernel or mainline otherwise (e.g. when cold booted) I did not get any
>> serial debug output at all. Enabling earlyprintk I got the following:
>>
>> [    1.136806] INFO: trying to register non-static key.
>> [    1.136871] 2020000.serial: ttymxc0 at MMIO 0x2020000 (irq = 25,
>> base_baud = 5000000) is a IMX
>> [    1.150651] the code is fine but needs lockdep annotation.
>> [    1.150653] turning off the locking correctness validator.
>> [    1.150664] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.4.0-rc6-
>> next-20151223-00002-g6008f30-dirty #27
>> [    1.150668] Hardware name: Freescale i.MX6 Quad/DualLite (Device
>> Tree)
>> [    1.150675] Backtrace:
>> [    1.150701] [<c010c45c>] (dump_backtrace) from [<c010c654>]
>> (show_stack+0x18/0x1c)
>> [    1.150722]  r7:00000000 r6:c0d20848 r5:00000000 r4:00000000
>> [    1.150739] [<c010c63c>] (show_stack) from [<c03dadcc>]
>> (dump_stack+0x8c/0xa4)
>> [    1.150760] [<c03dad40>] (dump_stack) from [<c016b60c>]
>> (__lock_acquire+0x1d88/0x1eb4)
>> [    1.150774]  r7:00000000 r6:c0d063f8 r5:c155f834 r4:e503bc20
>> [    1.150785] [<c0169884>] (__lock_acquire) from [<c016bf54>]
>> (lock_acquire+0x74/0x94)
>> [    1.150803]  r10:c0d6eb5e r9:e597b300 r8:00000019 r7:00000001
>> r6:00000001 r5:60000193
>> [    1.150808]  r4:00000000
>> [    1.150821] [<c016bee0>] (lock_acquire) from [<c08d49d4>]
>> (_raw_spin_lock_irqsave+0x40/0x54)
>> [    1.150834]  r7:000052c8 r6:c0481470 r5:40000193 r4:e503bc10
>> [    1.150852] [<c08d4994>] (_raw_spin_lock_irqsave) from [<c0481470>]
>> (imx_rxint+0x20/0x2a4)
>> [    1.150862]  r6:00000000 r5:000052d0 r4:e503bc10
>> [    1.150874] [<c0481450>] (imx_rxint) from [<c0482540>]
>> (imx_int+0x170/0x1f4)
>>
>> Debugging a little further I noticed this actually happening after
>> calling devm_request_irq() during serial_imx_probe() even before
>> uart_add_one_port()

The imx driver is in the minority by claiming the irq @ probe time.
The vast majority of uart drivers claim the irq in their startup() methods.

Regards,
Peter Hurley


>> did initialise the spin_lock acquired in
>> imx_rxint(). Turns out the data carrier detect interrupt fired
>> immediately upon requesting interrupts. This patch fixes this by
>> explicitly disabling data carrier detect before requesting interrupts.
> 
> I actually hit a very similar issue on the Colibri iMX6 and hence looked
> into this too. In our downstream tree, I fixed it in imx_startup, which
> is probably the wrong place actually...
> 
>>
>> Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
>>
>> ---
>>
>>  drivers/tty/serial/imx.c | 5 +++++
>>  1 file changed, 5 insertions(+)
>>
>> diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
>> index 9362f54c..b1588f9 100644
>> --- a/drivers/tty/serial/imx.c
>> +++ b/drivers/tty/serial/imx.c
>> @@ -2032,6 +2032,11 @@ static int serial_imx_probe(struct platform_device *pdev)
>>  		 UCR1_TXMPTYEN | UCR1_RTSDEN);
>>  	writel_relaxed(reg, sport->port.membase + UCR1);
>>  
>> +	/* Disable data carrier detect before requesting interrupts */
>> +	reg = readl_relaxed(sport->port.membase + UCR3);
>> +	reg &= ~(UCR3_DCD);
>> +	writel_relaxed(reg, sport->port.membase + UCR3);
>> +
> 
> Note that UCR3_DCD has a different meaning in DCE mode. As a DCE, the
> bit should be kept 1 (we assume that the carrier is detected by
> default...)
> 
> The dte_mode bit should be initialized at that point, hence just making
> that code conditional should account for that.
> 
> What I also noticed is that the RI signal suffers the very same issue.
> We do not use the signal on our Colibri board, but we should disable
> that interrupt too.
> 
> --
> Stefan
> 
>>  	clk_disable_unprepare(sport->clk_ipg);
>>  
>>  	/*