[PATCH 1/2] ARM: dts: r8a7793: add CAN clocks

[Simon Horman]

On Thu, Jan 21, 2016 at 09:15:27PM +0900, Simon Horman wrote:
> On 木,  1月 21, 2016 at 09:38:21午前 +0100, Geert Uytterhoeven wrote:
> > Hi Simon,
> > 
> > On Thu, Jan 21, 2016 at 6:09 AM, Simon Horman
> > <horms+renesas at verge.net.au> wrote:
> > > The R-Car CAN controllers can derive the CAN bus clock not only from their
> > > peripheral clock input (clkp1) but also from the other internal clock
> > > (clkp2) and external clock fed on CAN_CLK pin. Describe those clocks in
> > > the device tree along with  the USB_EXTAL clock from which clkp2 is
> > > derived.
> > >
> > > Based on work by Sergei Shtylyov for the r8a7791 SoC.
> > >
> > > Cc: Sergei Shtylyov <sergei.shtylyov at cogentembedded.com>
> > > Signed-off-by: Simon Horman <horms+renesas at verge.net.au>
> > > ---
> > >  arch/arm/boot/dts/r8a7793.dtsi | 20 +++++++++++++++++++-
> > >  1 file changed, 19 insertions(+), 1 deletion(-)
> > >
> > > diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
> > > index 0ce7cc420c9d..5d9375fa6759 100644
> > > --- a/arch/arm/boot/dts/r8a7793.dtsi
> > > +++ b/arch/arm/boot/dts/r8a7793.dtsi
> > > @@ -706,12 +706,30 @@
> > >                         clock-output-names = "extal";
> > >                 };
> > >
> > > +               /* External USB clock - can be overridden by the board */
> > > +               usb_extal_clk: usb_extal_clk {
> > > +                       compatible = "fixed-clock";
> > > +                       #clock-cells = <0>;
> > > +                       clock-frequency = <48000000>;
> > > +                       clock-output-names = "usb_extal";
> > > +               };
> > > +
> > > +               /* External CAN clock */
> > > +               can_clk: can_clk {
> > > +                       compatible = "fixed-clock";
> > > +                       #clock-cells = <0>;
> > > +                       /* This value must be overridden by the board. */
> > > +                       clock-frequency = <0>;
> > > +                       clock-output-names = "can_clk";
> > > +                       status = "disabled";
> > > +               };
> > > +
> > >                 /* Special CPG clocks */
> > >                 cpg_clocks: cpg_clocks at e6150000 {
> > >                         compatible = "renesas,r8a7793-cpg-clocks",
> > >                                      "renesas,rcar-gen2-cpg-clocks";
> > >                         reg = <0 0xe6150000 0 0x1000>;
> > > -                       clocks = <&extal_clk>;
> > > +                       clocks = <&extal_clk &usb_extal_clk>;
> > >                         #clock-cells = <1>;
> > >                         clock-output-names = "main", "pll0", "pll1", "pll3",
> > >                                              "lb", "qspi", "sdh", "sd0", "z",
> > 
> > To create the "rcan" clock, it should be listed in clock-output-names.

Checking this morning I see that it is already there.
The next line of the file is:

					     "rcan", "adsp";