[PATCH RFC 09/15] ARM: dts: sun6i: sina31s: Switch to mmc3 for onboard eMMC

[Chen-Yu Tsai]

On Thu, Jan 21, 2016 at 8:25 PM, Hans de Goede <hdegoede at redhat.com> wrote:
> Hi,
>
> On 21-01-16 13:23, Chen-Yu Tsai wrote:
>>
>> On Thu, Jan 21, 2016 at 7:16 PM, Hans de Goede <hdegoede at redhat.com>
>> wrote:
>>>
>>> Hi,
>>>
>>> On 21-01-16 06:26, Chen-Yu Tsai wrote:
>>>>
>>>>
>>>> According to Allwinner, only mmc3 supports 8 bit DDR transfers for eMMC.
>>>> Switch to mmc3 for the onboard eMMC, and also assign vqmmc for signal
>>>> voltage sensing/switching, and "cap-mmc-hw-reset" to denote this
>>>> instance can use eMMC hardware reset.
>>>
>>>
>>>
>>> This is going to need some more explanation, does this mean
>>> that the old dtsi is wrong and the emmc does not work there are all ?
>>
>>
>> mmc2 works fine for either 4 bit SDR/DDR or 8 bit SDR only. It does
>> not work for 8 bit DDR. I actually tested all the above combinations.
>>
>> Also see
>> https://groups.google.com/d/msg/linux-sunxi/pMzwMWwLALw/6WGgCN1eAQAJ
>>
>> About old DTs not working:
>>
>> a) The old DT will not work with the mmc patches, as it will try 8 bit DDR
>>     and fail. Also, the old DT does not use the highest drive strength for
>>     the mmc pins, meaning it might not work for the other chip families.
>>
>> b) Old DT + old kernel works fine (8 bit high-speed), just slower.
>>
>> An alternative would be to drop MMC_CAP_1_8V_DDR from the driver, and
>> use the "mmc-ddr-1_8v" DT capability flag at the dtsi or board level.
>> There's no real way to describe "don't use 8 bit with MMC DDR" in the DT.
>
>
> OK, so what is confusing me, is how can we choose between the emmc being
> connected to mmc2 resp mmc3, are there dipswitches on the board? Or can both
> mmc controllers be routed to the outside on the same port/pins ?

They are on the same pins, just with a different mux value/function.
I believe the previous patch explains this.

ChenYu

>
> Regards,
>
> Hans
>
>
>
>>
>>
>> Regards
>> ChenYu
>>
>>>
>>> Regards,
>>>
>>> Hans
>>>
>>>
>>>
>>>>
>>>> Signed-off-by: Chen-Yu Tsai <wens at csie.org>
>>>> ---
>>>>    arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi | 6 ++++--
>>>>    1 file changed, 4 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi
>>>> b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi
>>>> index ea69fb8ad4d8..4ec0c8679b2e 100644
>>>> --- a/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi
>>>> +++ b/arch/arm/boot/dts/sun6i-a31s-sina31s-core.dtsi
>>>> @@ -61,12 +61,14 @@
>>>>    };
>>>>
>>>>    /* eMMC on core board */
>>>> -&mmc2 {
>>>> +&mmc3 {
>>>>          pinctrl-names = "default";
>>>> -       pinctrl-0 = <&mmc2_8bit_emmc_pins>;
>>>> +       pinctrl-0 = <&mmc3_8bit_emmc_pins>;
>>>>          vmmc-supply = <&reg_dcdc1>;
>>>> +       vqmmc-supply = <&reg_dcdc1>;
>>>>          bus-width = <8>;
>>>>          non-removable;
>>>> +       cap-mmc-hw-reset;
>>>>          status = "okay";
>>>>    };
>>>>
>>>>
>>>
>