[PATCH v2 6/7] ARM: dts: kirkwood: split lswxl dts to linkstation lswsxl and lswxl
Roger Shimizu
rogershimizu at gmail.com
Wed Jan 20 07:33:57 PST 2016
LS-WXL/WSXL are both kirkwood-6281 based 2-Bay NAS devices, which share
many MPP pins. However they are slightly different:
- There're two red LED indicator on LS-WXL to show when HDD fails,
but there's no such on LS-WSXL.
- There's 4-level speed adjustable FAN on LS-WXL, but not LS-WSXL.
So after the split, common part goes into .dtsi file:
- kirkwood-linkstation.dtsi
- kirkwood-linkstation-duo-6281.dtsi
while all rest part goes into device specific .dts file:
- kirkwood-linkstation-lswsxl.dts
- kirkwood-linkstation-lswxl.dts
Signed-off-by: Roger Shimizu <rogershimizu at gmail.com>
---
.../devicetree/bindings/arm/marvell,kirkwood.txt | 3 +-
arch/arm/boot/dts/Makefile | 3 +-
.../boot/dts/kirkwood-linkstation-duo-6281.dtsi | 185 ++++++++++++
arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts | 57 ++++
arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts | 116 +++++++
arch/arm/boot/dts/kirkwood-linkstation.dtsi | 202 +++++++++++++
arch/arm/boot/dts/kirkwood-lswxl.dts | 334 ---------------------
7 files changed, 564 insertions(+), 336 deletions(-)
create mode 100644 arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi
create mode 100644 arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts
create mode 100644 arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts
create mode 100644 arch/arm/boot/dts/kirkwood-linkstation.dtsi
delete mode 100644 arch/arm/boot/dts/kirkwood-lswxl.dts
diff --git a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt
index 5171ad8f48ff..c7f8e3e97c78 100644
--- a/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt
+++ b/Documentation/devicetree/bindings/arm/marvell,kirkwood.txt
@@ -19,9 +19,10 @@ SoC. Currently known SoC compatibles are:
And in addition, the compatible shall be extended with the specific
board. Currently known boards are:
+"buffalo,linkstation-lswsxl"
+"buffalo,linkstation-lswxl"
"buffalo,lschlv2"
"buffalo,lswvl"
-"buffalo,lswxl"
"buffalo,lsxhl"
"buffalo,lsxl"
"dlink,dns-320"
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 30bbc3746130..788c75a69364 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -183,9 +183,10 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
kirkwood-is2.dtb \
kirkwood-km_kirkwood.dtb \
kirkwood-laplug.dtb \
+ kirkwood-linkstation-lswsxl.dtb \
+ kirkwood-linkstation-lswxl.dtb \
kirkwood-lschlv2.dtb \
kirkwood-lswvl.dtb \
- kirkwood-lswxl.dtb \
kirkwood-lsxhl.dtb \
kirkwood-mplcec4.dtb \
kirkwood-mv88f6281gtw-ge.dtb \
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi b/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi
new file mode 100644
index 000000000000..47b8f185839d
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-linkstation-duo-6281.dtsi
@@ -0,0 +1,185 @@
+/*
+ * Device Tree common file for kirkwood-6281 based 2-Bay Buffalo Linkstation
+ *
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu at gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+#include "kirkwood-linkstation.dtsi"
+
+/ {
+ ocp at f1000000 {
+ pinctrl: pin-controller at 10000 {
+ pmx_power_hdd0: pmx-power-hdd0 {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+ pmx_power_hdd1: pmx-power-hdd1 {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+ pmx_usb_vbus: pmx-usb-vbus {
+ marvell,pins = "mpp37";
+ marvell,function = "gpio";
+ };
+ pmx_led_alarm: pmx-led-alarm {
+ marvell,pins = "mpp49";
+ marvell,function = "gpio";
+ };
+ pmx_led_function_red: pmx-led-function-red {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+ pmx_led_function_blue: pmx-led-function-blue {
+ marvell,pins = "mpp36";
+ marvell,function = "gpio";
+ };
+ pmx_led_info: pmx-led-info {
+ marvell,pins = "mpp38";
+ marvell,function = "gpio";
+ };
+ pmx_led_power: pmx-led-power {
+ marvell,pins = "mpp39";
+ marvell,function = "gpio";
+ };
+ pmx_button_function: pmx-button-function {
+ marvell,pins = "mpp41";
+ marvell,function = "gpio";
+ };
+ pmx_power_switch: pmx-power-switch {
+ marvell,pins = "mpp42";
+ marvell,function = "gpio";
+ };
+ pmx_power_auto_switch: pmx-power-auto-switch {
+ marvell,pins = "mpp43";
+ marvell,function = "gpio";
+ };
+ };
+
+ sata at 80000 {
+ nr-ports = <2>;
+ };
+ };
+
+ gpio_keys {
+ function-button {
+ gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
+ };
+
+ power-on-switch {
+ gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
+ };
+
+ power-auto-switch {
+ gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio_leds {
+ red-alarm-led {
+ label = "linkstation:red:alarm";
+ gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
+ };
+
+ red-function-led {
+ label = "linkstation:red:function";
+ gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+ };
+
+ amber-info-led {
+ label = "linkstation:amber:info";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ };
+
+ blue-function-led {
+ label = "linkstation:blue:function";
+ gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
+ };
+
+ blue-power-led {
+ label = "linkstation:blue:power";
+ gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ regulators {
+ pinctrl-0 = <&pmx_power_hdd0 &pmx_power_hdd1 &pmx_usb_vbus>;
+
+ usb_power: regulator at 1 {
+ gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ };
+
+ hdd_power0: regulator at 2 {
+ gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+ };
+
+ hdd_power1: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "HDD1 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy1: ethernet-phy at 8 {
+ device_type = "ethernet-phy";
+ reg = <8>;
+ };
+};
+
+ð1 {
+ status = "okay";
+
+ ethernet1-port at 0 {
+ phy-handle = <ðphy1>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts b/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts
new file mode 100644
index 000000000000..4b6450186af5
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-linkstation-lswsxl.dts
@@ -0,0 +1,57 @@
+/*
+ * Device Tree file for Buffalo Linkstation LS-WSXL
+ *
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu at gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "kirkwood-linkstation-duo-6281.dtsi"
+
+/ {
+ model = "Buffalo Linkstation LS-WSXL";
+ compatible = "buffalo,lswsxl", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts b/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts
new file mode 100644
index 000000000000..ecd5c12a805d
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-linkstation-lswxl.dts
@@ -0,0 +1,116 @@
+/*
+ * Device Tree file for Buffalo Linkstation LS-WXL
+ *
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu at gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "kirkwood-linkstation-duo-6281.dtsi"
+
+/ {
+ model = "Buffalo Linkstation LS-WXL";
+ compatible = "buffalo,lswxl", "marvell,kirkwood-88f6281", "marvell,kirkwood";
+
+ memory { /* 128 MB */
+ device_type = "memory";
+ reg = <0x00000000 0x8000000>;
+ };
+
+ ocp at f1000000 {
+ pinctrl: pin-controller at 10000 {
+ pmx_led_hdderr0: pmx-led-hdderr0 {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+ pmx_led_hdderr1: pmx-led-hdderr1 {
+ marvell,pins = "mpp46";
+ marvell,function = "gpio";
+ };
+ pmx_fan_lock: pmx-fan-lock {
+ marvell,pins = "mpp40";
+ marvell,function = "gpio";
+ };
+ pmx_fan_high: pmx-fan-high {
+ marvell,pins = "mpp47";
+ marvell,function = "gpio";
+ };
+ pmx_fan_low: pmx-fan-low {
+ marvell,pins = "mpp48";
+ marvell,function = "gpio";
+ };
+ };
+ };
+
+ gpio_leds {
+ pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm
+ &pmx_led_info &pmx_led_power
+ &pmx_led_function_blue
+ &pmx_led_hdderr0
+ &pmx_led_hdderr1>;
+
+ red-hdderr0-led {
+ label = "linkstation:red:hdderr0";
+ gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
+ };
+
+ red-hdderr1-led {
+ label = "linkstation:red:hdderr1";
+ gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ gpio_fan {
+ compatible = "gpio-fan";
+ pinctrl-0 = <&pmx_fan_low &pmx_fan_high &pmx_fan_lock>;
+ pinctrl-names = "default";
+
+ gpios = <&gpio1 16 GPIO_ACTIVE_LOW
+ &gpio1 15 GPIO_ACTIVE_LOW>;
+
+ gpio-fan,speed-map = <0 3
+ 1500 2
+ 3250 1
+ 5000 0>;
+
+ alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-linkstation.dtsi b/arch/arm/boot/dts/kirkwood-linkstation.dtsi
new file mode 100644
index 000000000000..69061b6e987b
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-linkstation.dtsi
@@ -0,0 +1,202 @@
+/*
+ * Device Tree common file for kirkwood based Buffalo Linkstation
+ *
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu at gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/ {
+ chosen {
+ bootargs = "console=ttyS0,115200n8 earlyprintk";
+ stdout-path = &uart0;
+ };
+
+ mbus {
+ pcie-controller {
+ status = "okay";
+ pcie at 1,0 {
+ status = "okay";
+ };
+ };
+ };
+
+ ocp at f1000000 {
+ pinctrl: pin-controller at 10000 {
+ pmx_power_hdd0: pmx-power-hdd0 {
+ marvell,function = "gpio";
+ };
+ pmx_usb_vbus: pmx-usb-vbus {
+ marvell,function = "gpio";
+ };
+ pmx_led_alarm: pmx-led-alarm {
+ marvell,function = "gpio";
+ };
+ pmx_led_function_red: pmx-led-function-red {
+ marvell,function = "gpio";
+ };
+ pmx_led_function_blue: pmx-led-function-blue {
+ marvell,function = "gpio";
+ };
+ pmx_led_info: pmx-led-info {
+ marvell,function = "gpio";
+ };
+ pmx_led_power: pmx-led-power {
+ marvell,function = "gpio";
+ };
+ pmx_button_function: pmx-button-function {
+ marvell,function = "gpio";
+ };
+ pmx_power_switch: pmx-power-switch {
+ marvell,function = "gpio";
+ };
+ pmx_power_auto_switch: pmx-power-auto-switch {
+ marvell,function = "gpio";
+ };
+ };
+
+ serial at 12000 {
+ status = "okay";
+ };
+
+ sata at 80000 {
+ status = "okay";
+ nr-ports = <1>;
+ };
+
+ spi at 10600 {
+ status = "okay";
+
+ m25p40 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "st,m25p40", "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+ mode = <0>;
+
+ partition at 0 {
+ reg = <0x0 0x60000>;
+ label = "uboot";
+ read-only;
+ };
+
+ partition at 60000 {
+ reg = <0x60000 0x10000>;
+ label = "dtb";
+ read-only;
+ };
+
+ partition at 70000 {
+ reg = <0x70000 0x10000>;
+ label = "uboot_env";
+ };
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_button_function &pmx_power_switch
+ &pmx_power_auto_switch>;
+ pinctrl-names = "default";
+
+ function-button {
+ label = "Function Button";
+ linux,code = <KEY_OPTION>;
+ };
+
+ power-on-switch {
+ label = "Power-on Switch";
+ linux,code = <KEY_RESERVED>;
+ linux,input-type = <5>;
+ };
+
+ power-auto-switch {
+ label = "Power-auto Switch";
+ linux,code = <KEY_ESC>;
+ linux,input-type = <5>;
+ };
+ };
+
+ gpio_leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm
+ &pmx_led_info &pmx_led_power
+ &pmx_led_function_blue>;
+ pinctrl-names = "default";
+ };
+
+ restart_poweroff {
+ compatible = "restart-poweroff";
+ };
+
+ regulators {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ pinctrl-0 = <&pmx_power_hdd0 &pmx_usb_vbus>;
+ pinctrl-names = "default";
+
+ usb_power: regulator at 1 {
+ compatible = "regulator-fixed";
+ reg = <1>;
+ regulator-name = "USB Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ hdd_power0: regulator at 2 {
+ compatible = "regulator-fixed";
+ reg = <2>;
+ regulator-name = "HDD0 Power";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/kirkwood-lswxl.dts b/arch/arm/boot/dts/kirkwood-lswxl.dts
deleted file mode 100644
index 5bc0b597c9c2..000000000000
--- a/arch/arm/boot/dts/kirkwood-lswxl.dts
+++ /dev/null
@@ -1,334 +0,0 @@
-/*
- * Device Tree file for Buffalo Linkstation LS-WXL/WSXL
- *
- * Copyright (C) 2015, 2016
- * Roger Shimizu <rogershimizu at gmail.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-/dts-v1/;
-
-#include "kirkwood.dtsi"
-#include "kirkwood-6281.dtsi"
-
-/ {
- model = "Buffalo Linkstation LS-WXL/WSXL";
- compatible = "buffalo,lswxl", "marvell,kirkwood-88f6281", "marvell,kirkwood";
-
- memory { /* 128 MB */
- device_type = "memory";
- reg = <0x00000000 0x8000000>;
- };
-
- chosen {
- bootargs = "console=ttyS0,115200n8 earlyprintk";
- stdout-path = &uart0;
- };
-
- mbus {
- pcie-controller {
- status = "okay";
- pcie at 1,0 {
- status = "okay";
- };
- };
- };
-
- ocp at f1000000 {
- pinctrl: pin-controller at 10000 {
- pmx_power_hdd0: pmx-power-hdd0 {
- marvell,pins = "mpp28";
- marvell,function = "gpio";
- };
- pmx_power_hdd1: pmx-power-hdd1 {
- marvell,pins = "mpp29";
- marvell,function = "gpio";
- };
- pmx_usb_vbus: pmx-usb-vbus {
- marvell,pins = "mpp37";
- marvell,function = "gpio";
- };
- pmx_fan_high: pmx-fan-high {
- marvell,pins = "mpp47";
- marvell,function = "gpio";
- };
- pmx_fan_low: pmx-fan-low {
- marvell,pins = "mpp48";
- marvell,function = "gpio";
- };
- pmx_led_hdderr0: pmx-led-hdderr0 {
- marvell,pins = "mpp8";
- marvell,function = "gpio";
- };
- pmx_led_hdderr1: pmx-led-hdderr1 {
- marvell,pins = "mpp46";
- marvell,function = "gpio";
- };
- pmx_led_alarm: pmx-led-alarm {
- marvell,pins = "mpp49";
- marvell,function = "gpio";
- };
- pmx_led_function_red: pmx-led-function-red {
- marvell,pins = "mpp34";
- marvell,function = "gpio";
- };
- pmx_led_function_blue: pmx-led-function-blue {
- marvell,pins = "mpp36";
- marvell,function = "gpio";
- };
- pmx_led_info: pmx-led-info {
- marvell,pins = "mpp38";
- marvell,function = "gpio";
- };
- pmx_led_power: pmx-led-power {
- marvell,pins = "mpp39";
- marvell,function = "gpio";
- };
- pmx_fan_lock: pmx-fan-lock {
- marvell,pins = "mpp40";
- marvell,function = "gpio";
- };
- pmx_button_function: pmx-button-function {
- marvell,pins = "mpp41";
- marvell,function = "gpio";
- };
- pmx_power_switch: pmx-power-switch {
- marvell,pins = "mpp42";
- marvell,function = "gpio";
- };
- pmx_power_auto_switch: pmx-power-auto-switch {
- marvell,pins = "mpp43";
- marvell,function = "gpio";
- };
- };
-
- serial at 12000 {
- status = "okay";
- };
-
- sata at 80000 {
- status = "okay";
- nr-ports = <2>;
- };
-
- spi at 10600 {
- status = "okay";
-
- m25p40 at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "st,m25p40", "jedec,spi-nor";
- reg = <0>;
- spi-max-frequency = <25000000>;
- mode = <0>;
-
- partition at 0 {
- reg = <0x0 0x60000>;
- label = "uboot";
- read-only;
- };
-
- partition at 60000 {
- reg = <0x60000 0x10000>;
- label = "dtb";
- read-only;
- };
-
- partition at 70000 {
- reg = <0x70000 0x10000>;
- label = "uboot_env";
- };
- };
- };
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-0 = <&pmx_button_function &pmx_power_switch
- &pmx_power_auto_switch>;
- pinctrl-names = "default";
-
- button at 1 {
- label = "Function Button";
- linux,code = <KEY_OPTION>;
- gpios = <&gpio1 9 GPIO_ACTIVE_LOW>;
- };
-
- button at 2 {
- label = "Power-on Switch";
- linux,code = <KEY_RESERVED>;
- linux,input-type = <5>;
- gpios = <&gpio1 10 GPIO_ACTIVE_LOW>;
- };
-
- button at 3 {
- label = "Power-auto Switch";
- linux,code = <KEY_ESC>;
- linux,input-type = <5>;
- gpios = <&gpio1 11 GPIO_ACTIVE_LOW>;
- };
- };
-
- gpio_leds {
- compatible = "gpio-leds";
- pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm
- &pmx_led_info &pmx_led_power
- &pmx_led_function_blue
- &pmx_led_hdderr0
- &pmx_led_hdderr1>;
- pinctrl-names = "default";
-
- led at 1 {
- label = "lswxl:blue:func";
- gpios = <&gpio1 4 GPIO_ACTIVE_LOW>;
- };
-
- led at 2 {
- label = "lswxl:red:alarm";
- gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
- };
-
- led at 3 {
- label = "lswxl:amber:info";
- gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
- };
-
- led at 4 {
- label = "lswxl:blue:power";
- gpios = <&gpio1 7 GPIO_ACTIVE_LOW>;
- };
-
- led at 5 {
- label = "lswxl:red:func";
- gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
- };
-
- led at 6 {
- label = "lswxl:red:hdderr0";
- gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;
- };
-
- led at 7 {
- label = "lswxl:red:hdderr1";
- gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>;
- };
- };
-
- gpio_fan {
- compatible = "gpio-fan";
- pinctrl-0 = <&pmx_fan_low &pmx_fan_high &pmx_fan_lock>;
- pinctrl-names = "default";
-
- gpios = <&gpio1 16 GPIO_ACTIVE_LOW
- &gpio1 15 GPIO_ACTIVE_LOW>;
-
- gpio-fan,speed-map = <0 3
- 1500 2
- 3250 1
- 5000 0>;
-
- alarm-gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
- };
-
- restart_poweroff {
- compatible = "restart-poweroff";
- };
-
- regulators {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <0>;
- pinctrl-0 = <&pmx_power_hdd0 &pmx_power_hdd1 &pmx_usb_vbus>;
- pinctrl-names = "default";
-
- usb_power: regulator at 1 {
- compatible = "regulator-fixed";
- reg = <1>;
- regulator-name = "USB Power";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&gpio1 5 GPIO_ACTIVE_HIGH>;
- };
- hdd_power0: regulator at 2 {
- compatible = "regulator-fixed";
- reg = <2>;
- regulator-name = "HDD0 Power";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&gpio0 28 GPIO_ACTIVE_HIGH>;
- };
- hdd_power1: regulator at 3 {
- compatible = "regulator-fixed";
- reg = <3>;
- regulator-name = "HDD1 Power";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- enable-active-high;
- regulator-always-on;
- regulator-boot-on;
- gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>;
- };
- };
-};
-
-&mdio {
- status = "okay";
-
- ethphy1: ethernet-phy at 8 {
- device_type = "ethernet-phy";
- reg = <8>;
- };
-};
-
-ð1 {
- status = "okay";
-
- ethernet1-port at 0 {
- phy-handle = <ðphy1>;
- };
-};
--
2.1.4
More information about the linux-arm-kernel
mailing list