[RFC PATCH v2 0/4] CPUs capacity information for heterogeneous systems

[Juri Lelli]

Hi Catalin,

On 19/01/16 10:59, Catalin Marinas wrote:
> On Mon, Jan 18, 2016 at 05:42:58PM +0100, Vincent Guittot wrote:
> > On 18 January 2016 at 17:30, Juri Lelli <juri.lelli at arm.com> wrote:
> > > On 18/01/16 17:13, Vincent Guittot wrote:
> > >> On 18 January 2016 at 16:13, Juri Lelli <juri.lelli at arm.com> wrote:
> > >> > On 15/01/16 11:50, Steve Muckle wrote:
> > >> >> On 01/08/2016 06:09 AM, Juri Lelli wrote:
> > >> >> >  2. Dynamic profiling at boot (v2)
> > >> >> >
> > >> >> >     pros: - does not require a standardized definition of capacity
> > >> >> >           - cannot be incorrectly tuned (once benchmark is fixed)
> > >> >> >           - does not require user/integrator work
> > >> >> >
> > >> >> >     cons: - not easy to come up with a clean solution, as it seems interaction
> > >> >> >             with several subsystems (e.g., cpufreq) is required
> > >> >> >           - not easy to agree upon a single benchmark (that has to be both
> > >> >> >             representative and simple enough to run at boot)
> > >> >> >           - numbers might (and do) vary from boot to boot
> > >> >>
> > >> >> An important additional con that was mentioned earlier IIRC was the
> > >> >> additional boot time required for the benchmark.
> > >> >
> > >> > Right. I forgot about that.
> > >> >
> > >> >> Perhaps there could be
> > >> >> a kernel command line argument to bypass the benchmark if it is known
> > >> >> that predetermined values will be provided via sysfs later?
> > >> >>
> > >> >
> > >> > This might work, yes.
> > >>
> > >> Instead of command line, I prefer to use DT.
> 
> I fully agree. Command line doesn't scale with multiple CPUs, at most an
> option to bypass the benchmark (though we could just skip it when the DT
> values are present).
> 
> > >> Can't we use something similar to what is currently done in arm arch
> > >> for the early stage of the boot ? We don't have to provide performance
> > >> value for which it's difficult to find a consensus on how to define it
> > >> and which benchmark should be used. We use the micro arch and the
> > >> frequency of the core to define a relative capacity. This give us a
> > >> relatively good idea of the capacity of each core.
> > >
> > > I'm not sure I understand what you are proposing. arm arch is currently
> > > based on having static hardcoded data (efficiency values). But, this has
> > > already been NACKed for arm64 during last review of this RFC.
> > >
> > > Are you proposing something different?
> > 
> > No, i'm proposing to use it at boot time until the dynamic profiling
> > gives better value.
> > We don't have to set any new properties.
> > IIRC, It was nacked because it was of static hardcoded value that was
> > not always reflecting the best accurate capacity of a system. IMHO,
> > it's not that far from reality so can't this be used as an
> > intermediate step while waiting for dynamic profiling ?
> 
> My nack for hard-coded values still stands since this is not just about
> the microarchitecture (MIDR) but how the CPUs are integrated with the
> SoC, additional caches, memory latency, maximum clock frequency (or you
> rely on DT again to get this information and scale the initial CPU
> capacity/efficiency accordingly). MIDR does not capture SoC details.
> 
> Two questions:
> 
> 1. How is the boot time affected by the benchmark?
> 2. How is the boot time affected by considering all the CPUs the same?
> 
> My preference is for DT and sysfs (especially useful for
> development/tuning) but I'm not opposed to a boot-time benchmark if
> people insist on it. If the answer to point 2 is "insignificant", we
> could as well defer the capacity setting to user space (sysfs).
> 

Given that we are not targeting boot time with this, but rather better
performance afterwards, I don't expect significant differences; but,
I'll get numbers :).

Thanks,

- Juri