[PATCH v3 2/4] i2c: rk3x: add ops to caculate i2c clocks
David Wu
david.wu at rock-chips.com
Thu Jan 14 04:31:37 PST 2016
From: David Wu <wdc at rock-chips.com>
I2c Controller of rk3x is updated for the rules to caculate clocks.
So it need a new method to caculate i2c clock timing information
for new version. The current method is defined as v0, and new is
v1, next maybe v2......
Signed-off-by: David Wu <david.wu at rock-chips.com>
---
Changes in v3:
- use GENMASK(Andy)
- Too many arguments for ops func, use struct for them(Andy)
changes in v2:
- split patch to three patches(Heiko)
drivers/i2c/busses/i2c-rk3x.c | 80 +++++++++++++++++++++++++++++--------------
1 file changed, 54 insertions(+), 26 deletions(-)
diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c
index 1d86e8c..185e0f9 100644
--- a/drivers/i2c/busses/i2c-rk3x.c
+++ b/drivers/i2c/busses/i2c-rk3x.c
@@ -58,6 +58,11 @@ enum {
#define REG_CON_LASTACK BIT(5) /* 1: send NACK after last received byte */
#define REG_CON_ACTACK BIT(6) /* 1: stop if NACK is received */
+#define VERSION_MASK GENMASK(31, 16)
+#define VERSION_SHIFT 16
+
+#define RK3X_I2C_V0 0x0
+
/* REG_MRXADDR bits */
#define REG_MRXADDR_VALID(x) BIT(24 + (x)) /* [x*8+7:x*8] of MRX[R]ADDR valid */
@@ -90,10 +95,27 @@ struct rk3x_i2c_soc_data {
int grf_offset;
};
+/**
+ * struct rk3x_priv_i2c_timings - rk3x I2C timing information
+ * @div_low: Divider output for low
+ * @div_high: Divider output for high
+ */
+struct rk3x_priv_i2c_timings {
+ unsigned long div_low;
+ unsigned long div_high;
+};
+
+struct rk3x_i2c_ops {
+ int (*calc_clock)(unsigned long,
+ struct i2c_timings *,
+ struct rk3x_priv_i2c_timings *);
+};
+
struct rk3x_i2c {
struct i2c_adapter adap;
struct device *dev;
struct rk3x_i2c_soc_data *soc_data;
+ struct rk3x_i2c_ops ops;
/* Hardware resources */
void __iomem *regs;
@@ -102,6 +124,7 @@ struct rk3x_i2c {
/* Settings */
struct i2c_timings t;
+ struct rk3x_priv_i2c_timings t_priv;
/* Synchronization & notification */
spinlock_t lock;
@@ -431,21 +454,20 @@ out:
}
/**
- * Calculate divider values for desired SCL frequency
+ * Calculate timing clock info values for desired SCL frequency
*
* @clk_rate: I2C input clock rate
- * @t_input: Known I2C timing information.
- * @div_low: Divider output for low
- * @div_high: Divider output for high
+ * @t_input: Known I2C timing information
+ * @t_output: Caculated rk3x private timing information that would
+ * be written into regs
*
* Returns: 0 on success, -EINVAL if the goal SCL rate is too slow. In that case
* a best-effort divider value is returned in divs. If the target rate is
* too high, we silently use the highest possible rate.
*/
-static int rk3x_i2c_calc_divs(unsigned long clk_rate,
- struct i2c_timings *t_input,
- unsigned long *div_low,
- unsigned long *div_high)
+static int rk3x_i2c_v0_calc_clock(unsigned long clk_rate,
+ struct i2c_timings *t_input,
+ struct rk3x_priv_i2c_timings *t_output)
{
unsigned long spec_min_low_ns, spec_min_high_ns;
unsigned long spec_setup_start, spec_max_data_hold_ns;
@@ -553,8 +575,8 @@ static int rk3x_i2c_calc_divs(unsigned long clk_rate,
* Time needed to meet hold requirements is important.
* Just use that.
*/
- *div_low = min_low_div;
- *div_high = min_high_div;
+ t_output->div_low = min_low_div;
+ t_output->div_high = min_high_div;
} else {
/*
* We've got to distribute some time among the low and high
@@ -583,25 +605,25 @@ static int rk3x_i2c_calc_divs(unsigned long clk_rate,
/* Give low the "ideal" and give high whatever extra is left */
extra_low_div = ideal_low_div - min_low_div;
- *div_low = ideal_low_div;
- *div_high = min_high_div + (extra_div - extra_low_div);
+ t_output->div_low = ideal_low_div;
+ t_output->div_high = min_high_div + (extra_div - extra_low_div);
}
/*
* Adjust to the fact that the hardware has an implicit "+1".
* NOTE: Above calculations always produce div_low > 0 and div_high > 0.
*/
- *div_low = *div_low - 1;
- *div_high = *div_high - 1;
+ t_output->div_low = t_output->div_low - 1;
+ t_output->div_high = t_output->div_high - 1;
/* Maximum divider supported by hw is 0xffff */
- if (*div_low > 0xffff) {
- *div_low = 0xffff;
+ if (t_output->div_low > 0xffff) {
+ t_output->div_low = 0xffff;
ret = -EINVAL;
}
- if (*div_high > 0xffff) {
- *div_high = 0xffff;
+ if (t_output->div_high > 0xffff) {
+ t_output->div_high = 0xffff;
ret = -EINVAL;
}
@@ -610,19 +632,21 @@ static int rk3x_i2c_calc_divs(unsigned long clk_rate,
static void rk3x_i2c_adapt_div(struct rk3x_i2c *i2c, unsigned long clk_rate)
{
- unsigned long div_low, div_high;
u64 t_low_ns, t_high_ns;
int ret;
- ret = rk3x_i2c_calc_divs(clk_rate, &i2c->t, &div_low, &div_high);
+ ret = i2c->ops.calc_clock(clk_rate, &i2c->t, &i2c->t_priv);
WARN_ONCE(ret != 0, "Could not reach SCL freq %u", i2c->t.bus_freq_hz);
clk_enable(i2c->clk);
- i2c_writel(i2c, (div_high << 16) | (div_low & 0xffff), REG_CLKDIV);
+ i2c_writel(i2c, (i2c->t_priv.div_high << 16) |
+ (i2c->t_priv.div_low & 0xffff), REG_CLKDIV);
clk_disable(i2c->clk);
- t_low_ns = div_u64(((u64)div_low + 1) * 8 * 1000000000, clk_rate);
- t_high_ns = div_u64(((u64)div_high + 1) * 8 * 1000000000, clk_rate);
+ t_low_ns = div_u64(((u64)i2c->t_priv.div_low + 1) * 8 * 1000000000,
+ clk_rate);
+ t_high_ns = div_u64(((u64)i2c->t_priv.div_high + 1) * 8 * 1000000000,
+ clk_rate);
dev_dbg(i2c->dev,
"CLK %lukhz, Req %uns, Act low %lluns high %lluns\n",
clk_rate / 1000,
@@ -652,12 +676,11 @@ static int rk3x_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
{
struct clk_notifier_data *ndata = data;
struct rk3x_i2c *i2c = container_of(nb, struct rk3x_i2c, clk_rate_nb);
- unsigned long div_low, div_high;
switch (event) {
case PRE_RATE_CHANGE:
- if (rk3x_i2c_calc_divs(ndata->new_rate, &i2c->t,
- &div_low, &div_high) != 0)
+ if (i2c->ops.calc_clock(ndata->new_rate, &i2c->t,
+ &i2c->t_priv) != 0)
return NOTIFY_STOP;
/* scale up */
@@ -861,6 +884,7 @@ static int rk3x_i2c_probe(struct platform_device *pdev)
u32 value;
int irq;
unsigned long clk_rate;
+ unsigned int version;
i2c = devm_kzalloc(&pdev->dev, sizeof(struct rk3x_i2c), GFP_KERNEL);
if (!i2c)
@@ -944,6 +968,10 @@ static int rk3x_i2c_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, i2c);
+ version = (readl(i2c->regs + REG_CON) & VERSION_MASK) >> VERSION_SHIFT;
+ if (version == RK3X_I2C_V0)
+ i2c->ops.calc_clock = rk3x_i2c_v0_calc_clock;
+
ret = clk_prepare(i2c->clk);
if (ret < 0) {
dev_err(&pdev->dev, "Could not prepare clock\n");
--
1.9.1
More information about the linux-arm-kernel
mailing list