[PATCH v3 1/2] power: act8945a: add charger driver for ACT8945A
Yang, Wenyou
Wenyou.Yang at atmel.com
Tue Jan 12 20:31:09 PST 2016
Hi Krzysztof,
> -----Original Message-----
> From: Krzysztof Kozlowski [mailto:k.kozlowski at samsung.com]
> Sent: 2016年1月13日 12:10
> To: Yang, Wenyou <Wenyou.Yang at atmel.com>; Sebastian Reichel
> <sre at kernel.org>; Dmitry Eremin-Solenikov <dbaryshkov at gmail.com>; David
> Woodhouse <dwmw2 at infradead.org>; Rob Herring <robh+dt at kernel.org>; Pawel
> Moll <pawel.moll at arm.com>; Mark Rutland <mark.rutland at arm.com>; Ian
> Campbell <ijc+devicetree at hellion.org.uk>; Kumar Gala <galak at codeaurora.org>
> Cc: Javier Martinez Canillas <javier at dowhile0.org>; Lee Jones
> <lee.jones at linaro.org>; Ferre, Nicolas <Nicolas.FERRE at atmel.com>; linux-arm-
> kernel at lists.infradead.org; linux-kernel at vger.kernel.org; linux-
> pm at vger.kernel.org
> Subject: Re: [PATCH v3 1/2] power: act8945a: add charger driver for ACT8945A
>
> On 13.01.2016 12:53, Yang, Wenyou wrote:
> > Hi Krzysztof,
> >
> > Thank you!
> >
> >> -----Original Message-----
> >> From: Krzysztof Kozlowski [mailto:k.kozlowski at samsung.com]
> >> Sent: 2016年1月13日 10:12
> >> To: Yang, Wenyou <Wenyou.Yang at atmel.com>; Sebastian Reichel
> >> <sre at kernel.org>; Dmitry Eremin-Solenikov <dbaryshkov at gmail.com>;
> >> David Woodhouse <dwmw2 at infradead.org>; Rob Herring
> >> <robh+dt at kernel.org>; Pawel Moll <pawel.moll at arm.com>; Mark Rutland
> >> <mark.rutland at arm.com>; Ian Campbell <ijc+devicetree at hellion.org.uk>;
> >> Kumar Gala <galak at codeaurora.org>
> >> Cc: Javier Martinez Canillas <javier at dowhile0.org>; Lee Jones
> >> <lee.jones at linaro.org>; Ferre, Nicolas <Nicolas.FERRE at atmel.com>;
> >> linux-arm- kernel at lists.infradead.org; linux-kernel at vger.kernel.org;
> >> linux- pm at vger.kernel.org
> >> Subject: Re: [PATCH v3 1/2] power: act8945a: add charger driver for
> >> ACT8945A
> >>
> >> On 12.01.2016 17:09, Wenyou Yang wrote:
> >>> This patch adds new driver for Active-semi ACT8945A ActivePath
> >>> charger (part of ACT8945A MFD driver) providing power supply class
> >>> information to userspace.
> >>>
> >>> The driver is configured through DTS (battery and system related
> >>> settings) and sysfs entries (timers and input over-voltage threshold).
> >>>
> >>> Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
> >>> ---
> >>>
> >>> Changes in v3:
> >>> - update the file header with short version license and author line.
> >>> - remove unused member of struct act8945a_charger, dev.
> >>> - action due to removing the member of stuct act8945a_dev, dev.
> >>> - remove the unnecessary print out.
> >>> - remove the unnecessary act8945a_charger_remove().
> >>> - fix align of the code-style.
> >>>
> >>> Changes in v2:
> >>> 1./ Substitute of_property_read_bool() for of_get_property().
> >>> 2./ Substitute devm_power_supply_register() for power_supply_register().
> >>> 3./ Use module_platform_driver(), instead of subsys_initcall().
> >>> 4./ Substitute MODULE_LICENSE("GPL") for MODULE_LICENSE("GPL v2").
> >>>
> >>> drivers/power/Kconfig | 7 +
> >>> drivers/power/Makefile | 1 +
> >>> drivers/power/act8945a_charger.c | 367
> >>> ++++++++++++++++++++++++++++++++++++++
> >>> 3 files changed, 375 insertions(+)
> >>> create mode 100644 drivers/power/act8945a_charger.c
> >>>
> >>> diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index
> >>> 1ddd13c..ae75211 100644
> >>> --- a/drivers/power/Kconfig
> >>> +++ b/drivers/power/Kconfig
> >>> @@ -75,6 +75,13 @@ config BATTERY_88PM860X
> >>> help
> >>> Say Y here to enable battery monitor for Marvell 88PM860x chip.
> >>>
> >>> +config BATTERY_ACT8945A
> >>> + tristate "Active-semi ACT8945A charger driver"
> >>> + depends on MFD_ACT8945A
> >>> + help
> >>> + Say Y here to enable support for power supply provided by
> >>> + Active-semi ActivePath ACT8945A charger.
> >>> +
> >>> config BATTERY_DS2760
> >>> tristate "DS2760 battery driver (HP iPAQ & others)"
> >>> depends on W1 && W1_SLAVE_DS2760
> >>> diff --git a/drivers/power/Makefile b/drivers/power/Makefile index
> >>> 0e4eab5..e46b75d 100644
> >>> --- a/drivers/power/Makefile
> >>> +++ b/drivers/power/Makefile
> >>> @@ -17,6 +17,7 @@ obj-$(CONFIG_WM8350_POWER) +=
> >> wm8350_power.o
> >>> obj-$(CONFIG_TEST_POWER) += test_power.o
> >>>
> >>> obj-$(CONFIG_BATTERY_88PM860X) += 88pm860x_battery.o
> >>> +obj-$(CONFIG_BATTERY_ACT8945A) += act8945a_charger.o
> >>> obj-$(CONFIG_BATTERY_DS2760) += ds2760_battery.o
> >>> obj-$(CONFIG_BATTERY_DS2780) += ds2780_battery.o
> >>> obj-$(CONFIG_BATTERY_DS2781) += ds2781_battery.o
> >>> diff --git a/drivers/power/act8945a_charger.c
> >>> b/drivers/power/act8945a_charger.c
> >>> new file mode 100644
> >>> index 0000000..643a2ed
> >>> --- /dev/null
> >>> +++ b/drivers/power/act8945a_charger.c
> >>> @@ -0,0 +1,367 @@
> >>> +/*
> >>> + * Power supply driver for the Active-semi ACT8945A PMIC
> >>> + *
> >>> + * Copyright (C) 2015 Atmel Corporation
> >>> + *
> >>> + * Author: Wenyou Yang <wenyou.yang at atmel.com>
> >>> + *
> >>> + * This program is free software; you can redistribute it and/or
> >>> +modify
> >>> + * it under the terms of the GNU General Public License version 2
> >>> +as
> >>> + * published by the Free Software Foundation.
> >>> + *
> >>> + */
> >>> +#include <linux/module.h>
> >>> +#include <linux/mfd/act8945a.h>
> >>> +#include <linux/of.h>
> >>> +#include <linux/of_gpio.h>
> >>> +#include <linux/platform_device.h>
> >>> +#include <linux/power_supply.h>
> >>> +#include <linux/regmap.h>
> >>> +
> >>> +static const char *act8945a_charger_model = "ACT8945A"; static
> >>> +const char *act8945a_charger_manufacturer = "Active-semi";
> >>> +
> >>> +/**
> >>> + * ACT8945A Charger Register Map
> >>> + */
> >>> +
> >>> +/* 0x70: Reserved */
> >>> +#define ACT8945A_APCH_CFG 0x71
> >>> +#define ACT8945A_APCH_STATUS 0x78
> >>> +#define ACT8945A_APCH_CTRL 0x79
> >>> +#define ACT8945A_APCH_STATE 0x7A
> >>> +
> >>> +/* ACT8945A_APCH_CFG */
> >>> +#define APCH_CFG_OVPSET (0x03 << 0)
> >>> +#define APCH_CFG_OVPSET_6V6 (0x0 << 0)
> >>> +#define APCH_CFG_OVPSET_7V (0x1 << 0)
> >>> +#define APCH_CFG_OVPSET_7V5 (0x2 << 0)
> >>> +#define APCH_CFG_OVPSET_8V (0x3 << 0)
> >>
> >> Why the tabs after #define? Nooooo...
> >>
> >>> +#define APCH_CFG_PRETIMO (0x03 << 2)
> >>> +#define APCH_CFG_PRETIMO_40_MIN (0x0 << 2)
> >>> +#define APCH_CFG_PRETIMO_60_MIN (0x1 << 2)
> >>> +#define APCH_CFG_PRETIMO_80_MIN (0x2 << 2)
> >>> +#define APCH_CFG_PRETIMO_DISABLED (0x3 << 2)
> >>> +#define APCH_CFG_TOTTIMO (0x03 << 4)
> >>> +#define APCH_CFG_TOTTIMO_3_HOUR (0x0 << 4)
> >>> +#define APCH_CFG_TOTTIMO_4_HOUR (0x1 << 4)
> >>> +#define APCH_CFG_TOTTIMO_5_HOUR (0x2 << 4)
> >>> +#define APCH_CFG_TOTTIMO_DISABLED (0x3 << 4)
> >>> +#define APCH_CFG_SUSCHG (0x01 << 7)
> >>> +
> >>> +#define APCH_STATUS_CHGDAT (0x01 << 0)
> >>> +#define APCH_STATUS_INDAT (0x01 << 1)
> >>> +#define APCH_STATUS_TEMPDAT (0x01 << 2)
> >>> +#define APCH_STATUS_TIMRDAT (0x01 << 3)
> >>> +#define APCH_STATUS_CHGSTAT (0x01 << 4)
> >>> +#define APCH_STATUS_INSTAT (0x01 << 5)
> >>> +#define APCH_STATUS_TEMPSTAT (0x01 << 6)
> >>> +#define APCH_STATUS_TIMRSTAT (0x01 << 7)
> >>> +
> >>> +#define APCH_CTRL_CHGEOCOUT (0x01 << 0)
> >>> +#define APCH_CTRL_INDIS (0x01 << 1)
> >>> +#define APCH_CTRL_TEMPOUT (0x01 << 2)
> >>> +#define APCH_CTRL_TIMRPRE (0x01 << 3)
> >>> +#define APCH_CTRL_CHGEOCIN (0x01 << 4)
> >>> +#define APCH_CTRL_INCON (0x01 << 5)
> >>> +#define APCH_CTRL_TEMPIN (0x01 << 6)
> >>> +#define APCH_CTRL_TIMRTOT (0x01 << 7)
> >>
> >> For the STATUS and CTRL use BIT(n) macro.
> >>
> >>
> >>> +
> >>> +#define APCH_STATE_ACINSTAT (0x01 << 1)
> >>> +#define APCH_STATE_CSTATE (0x03 << 4)
> >>> +#define APCH_STATE_CSTATE_SHIFT 4
> >>> +#define APCH_STATE_CSTATE_DISABLED 0x00
> >>> +#define APCH_STATE_CSTATE_EOC 0x01
> >>> +#define APCH_STATE_CSTATE_FAST 0x02
> >>> +#define APCH_STATE_CSTATE_PRE 0x03
> >>> +
> >>> +struct act8945a_charger {
> >>> + struct act8945a_dev *act8945a_dev;
> >>> + struct power_supply *psy;
> >>> +
> >>> + u32 tolal_time_out;
> >>> + u32 pre_time_out;
> >>> + u32 input_voltage_threshold;
> >>> + bool battery_temperature;
> >>> + int chglev_pin;
> >>> + int chglev_value;
> >>> +};
> >>> +
> >>> +static int act8945a_get_charger_state(struct regmap *regmap, int
> >>> +*val) {
> >>> + int ret;
> >>> + unsigned int status, state;
> >>> +
> >>> + ret = regmap_read(regmap, ACT8945A_APCH_STATUS, &status);
> >>> + if (ret < 0)
> >>> + return ret;
> >>> +
> >>> + ret = regmap_read(regmap, ACT8945A_APCH_STATE, &state);
> >>> + if (ret < 0)
> >>> + return ret;
> >>> +
> >>> + state &= APCH_STATE_CSTATE;
> >>> + state >>= APCH_STATE_CSTATE_SHIFT;
> >>> +
> >>> + if (state == APCH_STATE_CSTATE_EOC) {
> >>> + if (status & APCH_STATUS_CHGDAT)
> >>> + *val = POWER_SUPPLY_STATUS_FULL;
> >>> + else
> >>> + *val = POWER_SUPPLY_STATUS_NOT_CHARGING;
> >>> + } else if ((state == APCH_STATE_CSTATE_FAST) ||
> >>> + (state == APCH_STATE_CSTATE_PRE)) {
> >>> + *val = POWER_SUPPLY_STATUS_CHARGING;
> >>> + } else {
> >>> + *val = POWER_SUPPLY_STATUS_NOT_CHARGING;
> >>> + }
> >>> +
> >>> + return 0;
> >>> +}
> >>> +
> >>> +static int act8945a_get_charge_type(struct regmap *regmap, int
> >>> +*val) {
> >>> + int ret;
> >>> + unsigned int state;
> >>> +
> >>> + ret = regmap_read(regmap, ACT8945A_APCH_STATE, &state);
> >>> + if (ret < 0)
> >>> + return ret;
> >>> +
> >>> + state &= APCH_STATE_CSTATE;
> >>> + state >>= APCH_STATE_CSTATE_SHIFT;
> >>> +
> >>> + switch (state) {
> >>> + case APCH_STATE_CSTATE_PRE:
> >>> + *val = POWER_SUPPLY_CHARGE_TYPE_TRICKLE;
> >>> + break;
> >>> + case APCH_STATE_CSTATE_FAST:
> >>> + *val = POWER_SUPPLY_CHARGE_TYPE_FAST;
> >>> + break;
> >>> + case APCH_STATE_CSTATE_EOC:
> >>> + case APCH_STATE_CSTATE_DISABLED:
> >>> + default:
> >>> + *val = POWER_SUPPLY_CHARGE_TYPE_NONE;
> >>> + }
> >>> +
> >>> + return 0;
> >>> +}
> >>> +
> >>> +static int act8945a_get_battery_health(struct act8945a_charger *charger,
> >>> + struct regmap *regmap, int *val) {
> >>> + int ret;
> >>> + unsigned int status;
> >>> +
> >>> + ret = regmap_read(regmap, ACT8945A_APCH_STATUS, &status);
> >>> + if (ret < 0)
> >>> + return ret;
> >>> +
> >>> + if (charger->battery_temperature && !(status &
> >> APCH_STATUS_TEMPDAT))
> >>> + *val = POWER_SUPPLY_HEALTH_OVERHEAT;
> >>> + else if (!(status & APCH_STATUS_INDAT))
> >>> + *val = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
> >>> + else if (status & APCH_STATUS_TIMRDAT)
> >>> + *val = POWER_SUPPLY_HEALTH_SAFETY_TIMER_EXPIRE;
> >>> + else
> >>> + *val = POWER_SUPPLY_HEALTH_GOOD;
> >>> +
> >>> + return 0;
> >>> +}
> >>> +
> >>> +static enum power_supply_property act8945a_charger_props[] = {
> >>> + POWER_SUPPLY_PROP_STATUS,
> >>> + POWER_SUPPLY_PROP_CHARGE_TYPE,
> >>> + POWER_SUPPLY_PROP_TECHNOLOGY,
> >>> + POWER_SUPPLY_PROP_HEALTH,
> >>> + POWER_SUPPLY_PROP_MODEL_NAME,
> >>> + POWER_SUPPLY_PROP_MANUFACTURER
> >>> +};
> >>> +
> >>> +static int act8945a_charger_get_property(struct power_supply *psy,
> >>> + enum power_supply_property prop,
> >>> + union power_supply_propval *val) {
> >>> + struct act8945a_charger *charger = power_supply_get_drvdata(psy);
> >>> + struct regmap *regmap = charger->act8945a_dev->regmap;
> >>> + int ret = 0;
> >>> +
> >>> + switch (prop) {
> >>> + case POWER_SUPPLY_PROP_STATUS:
> >>> + ret = act8945a_get_charger_state(regmap, &val->intval);
> >>> + break;
> >>> + case POWER_SUPPLY_PROP_CHARGE_TYPE:
> >>> + ret = act8945a_get_charge_type(regmap, &val->intval);
> >>> + break;
> >>> + case POWER_SUPPLY_PROP_TECHNOLOGY:
> >>> + val->intval = POWER_SUPPLY_TECHNOLOGY_LION;
> >>> + break;
> >>> + case POWER_SUPPLY_PROP_HEALTH:
> >>> + ret = act8945a_get_battery_health(charger,
> >>> + regmap, &val->intval);
> >>> + break;
> >>> + case POWER_SUPPLY_PROP_MODEL_NAME:
> >>> + val->strval = act8945a_charger_model;
> >>> + break;
> >>> + case POWER_SUPPLY_PROP_MANUFACTURER:
> >>> + val->strval = act8945a_charger_manufacturer;
> >>> + break;
> >>> + default:
> >>> + return -EINVAL;
> >>> + }
> >>> +
> >>> + return ret;
> >>> +}
> >>> +
> >>> +static const struct power_supply_desc act8945a_charger_desc = {
> >>> + .name = "act8945a-charger",
> >>> + .type = POWER_SUPPLY_TYPE_BATTERY,
> >>> + .get_property = act8945a_charger_get_property,
> >>> + .properties = act8945a_charger_props,
> >>> + .num_properties = ARRAY_SIZE(act8945a_charger_props),
> >>> +};
> >>> +
> >>> +#define DEFAULT_TOTAL_TIME_OUT 3
> >>> +#define DEFAULT_PRE_TIME_OUT 40
> >>> +#define DEFAULT_INPUT_OVP_THRESHOLD 6600
> >>> +
> >>> +static int act8945a_charger_parse_dt(struct device *dev,
> >>> + struct act8945a_charger *charger) {
> >>> + struct device_node *np = dev->of_node;
> >>> + enum of_gpio_flags flags;
> >>> +
> >>> + if (!np) {
> >>> + dev_err(dev, "no charger of node\n");
> >>> + return -EINVAL;
> >>> + }
> >>> +
> >>> + charger->chglev_pin = of_get_named_gpio_flags(np,
> >>> + "active-semi,chglev-gpio", 0, &flags);
> >>> +
> >>> + charger->chglev_value = (flags == OF_GPIO_ACTIVE_LOW) ? 0 : 1;
> >>> +
> >>> + charger->battery_temperature = of_property_read_bool(np,
> >>> + "active-semi,battery_temperature");
> >>> +
> >>> + if (of_property_read_u32(np, "active-semi,input_voltage_threshold",
> >>> + &charger->input_voltage_threshold))
> >>> + charger->input_voltage_threshold = DEFAULT_PRE_TIME_OUT;
> >>> +
> >>> + if (of_property_read_u32(np, "active-semi,precondition_timeout",
> >>> + &charger->pre_time_out))
> >>> + charger->pre_time_out = DEFAULT_PRE_TIME_OUT;
> >>> +
> >>> + if (of_property_read_u32(np, "active-semi,total_timeout",
> >>> + &charger->tolal_time_out))
> >>> + charger->tolal_time_out = DEFAULT_TOTAL_TIME_OUT;
> >>> +
> >>> + return 0;
> >>> +}
> >>> +
> >>> +static int act8945a_charger_config(struct act8945a_charger
> >>> +*charger) {
> >>> + struct regmap *regmap = charger->act8945a_dev->regmap;
> >>> + u8 value = 0;
> >>
> >> Regmap uses "unsigned int". I think it is better not to mix it so use
> >> in the driver "unsigned int" for interactions with regmap.
> >
> > I checked, it seems they are not mixed in the patch. Or I am wrong?
>
> I mean that use "unsigned int value = 0;" here. You're going cast it anyway to
> unsigned int when calling regmap functions.
>
> >
> >>
> >> [...]
> >>
> >> Javier pointed the auto-loading issue before (because you are not
> >> providing any device table). Probably that is not what you want.
> >
> > Yes, but I still don't understand for now ...
>
> Try building this as module and check whether it got automatically loaded during
> boot. :)
Thank you for your help!
I will try.
Best Regards,
Wenyou Yang
More information about the linux-arm-kernel
mailing list