[PATCH v3 2/2] power: add documentation for ACT8945A's charger DT bindings

[Yang, Wenyou]

Hi Krzysztof,

Thank you for your so much feedback.

I will change it in next version.

> -----Original Message-----
> From: Krzysztof Kozlowski [mailto:k.kozlowski at samsung.com]
> Sent: 2016年1月13日 10:00
> To: Yang, Wenyou <Wenyou.Yang at atmel.com>; Sebastian Reichel
> <sre at kernel.org>; Dmitry Eremin-Solenikov <dbaryshkov at gmail.com>; David
> Woodhouse <dwmw2 at infradead.org>; Rob Herring <robh+dt at kernel.org>; Pawel
> Moll <pawel.moll at arm.com>; Mark Rutland <mark.rutland at arm.com>; Ian
> Campbell <ijc+devicetree at hellion.org.uk>; Kumar Gala <galak at codeaurora.org>
> Cc: Javier Martinez Canillas <javier at dowhile0.org>; Lee Jones
> <lee.jones at linaro.org>; Ferre, Nicolas <Nicolas.FERRE at atmel.com>; linux-arm-
> kernel at lists.infradead.org; linux-kernel at vger.kernel.org; linux-
> pm at vger.kernel.org
> Subject: Re: [PATCH v3 2/2] power: add documentation for ACT8945A's charger
> DT bindings
> 
> On 12.01.2016 17:09, Wenyou Yang wrote:
> > This patch adds documentation for the DT bindings of the charger
> > subdevice of ACT8945A MFD.
> >
> > Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
> > ---
> >
> > Changes in v3: None
> > Changes in v2: None
> >
> >  .../devicetree/bindings/power/act8945a-charger.txt |   34
> ++++++++++++++++++++
> >  1 file changed, 34 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/power/act8945a-charger.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/power/act8945a-charger.txt
> > b/Documentation/devicetree/bindings/power/act8945a-charger.txt
> > new file mode 100644
> > index 0000000..868e0164
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/power/act8945a-charger.txt
> > @@ -0,0 +1,34 @@
> > +Device-Tree bindings for charger of Active-semi ACT8945A
> > +Multi-Function Device
> > +
> > +Required properties:
> > + - compatible: "active-semi,act8945a-charger"
> > + - active-semi,chglev-gpio = Specifies a gpio that uses to select
> > +   the charge current level.
> 
> active-semi,chglev-gpios
> See: Documentation/devicetree/bindings/gpio/gpio.txt
> 
> > +
> > +Optional properties:
> > + - active-semi,battery_temperature: Indicates if it is allowed to check
> > +   the battery temperature. If it is missing, assume the battery temperature
> > +   is not allowed to check.
> 
> Here and in rest of properties - no underscores but hyphens. The name suggests
> that this is a value... but this is a boolean?
> 
> > + - active-semi,input_voltage_threshold: unit: mV;
> > +   Specifies the charger's input over-voltage threshold value;
> > +   The value can be: 6600, 7000, 7500, 8000; default: 6600
> 
> I think adding units suffix in binding is preferred. so "-microvolt"?
> 
> Best regards,
> Krzysztof
> 
> 
> > + - active-semi,precondition_timeout: unit: minutes;
> > +   Specifies the charger's PRECONDITION safety timer setting value;
> > +   The value can be: 40, 60, 80, 0; If 0, it means to disable this timer;
> > +   default: 40.
> > + - active-semi,total_timeout: unit: hours;
> > +   Specifies the charger's total safety timer setting value;
> > +   The value can be: 3, 4, 5, 0; If 0, it means to disable this timer;
> > +   default: 3.
> > +
> > +Example:
> > +
> > +	charger {
> > +		compatible = "active-semi,act8945a-charger";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_charger_chglev>;
> > +		active-semi,chglev-gpio = <&pioA 12 GPIO_ACTIVE_HIGH>;
> > +		active-semi,input_voltage_threshold = <6600>;
> > +		active-semi,precondition_timeout = <40>;
> > +		active-semi,total_timeout = <3>;
> > +	};
> >


Best Regards,
Wenyou Yang