[PATCH v8 20/20] KVM: ARM64: Add a new kvm ARM PMU device

[Christoffer Dall]

On Mon, Jan 11, 2016 at 03:07:17PM +0100, Andrew Jones wrote:
> On Sat, Jan 09, 2016 at 03:03:39PM +0000, Marc Zyngier wrote:
> > On Sat, 9 Jan 2016 13:29:56 +0100
> > Christoffer Dall <christoffer.dall at linaro.org> wrote:
> > 
> > > On Thu, Jan 07, 2016 at 09:36:47PM +0100, Andrew Jones wrote:
> > > > On Thu, Jan 07, 2016 at 02:56:15PM +0000, Peter Maydell wrote:
> > > > > On 7 January 2016 at 14:49, Shannon Zhao <zhaoshenglong at huawei.com> wrote:
> > > > > >>> +
> > > > > >>> +Groups:
> > > > > >>> +  KVM_DEV_ARM_PMU_GRP_IRQ
> > > > > >>> +  Attributes:
> > > > > >>> +    The attr field of kvm_device_attr encodes one value:
> > > > > >>> +    bits:     | 63 .... 32 | 31 ....  0 |
> > > > > >>> +    values:   |  reserved  | vcpu_index |
> > > > > >>> +    A value describing the PMU overflow interrupt number for the specified
> > > > > >>> +    vcpu_index vcpu. This interrupt could be a PPI or SPI, but for one VM the
> > > > > >>> +    interrupt type must be same for each vcpu. As a PPI, the interrupt number is
> > > > > >>> +    same for all vcpus, while as a SPI it must be different for each vcpu.
> > > > > >>
> > > > > >> I see we're using vcpu_index rather than MPIDR affinity value
> > > > > >> for specifying which CPU we're configuring. Is this in line with
> > > > > >> our planned API for GICv3 configuration?
> > > > > >>
> > > > > > Here vcpu_index is used to indexing the vCPU, no special use.
> > > > > 
> > > > > Yes, but you can identify the CPU by index, or by its MPIDR.
> > > > > We had a discussion about which was the best way for doing
> > > > > the VGIC API, and I can't remember which way round we ended up
> > > > > going for. Whichever we chose, we should do the same thing here.
> > > > 
> > > > I think we should start up a new discussion on this. My understanding,
> > > > after a chat with Igor, who was involved in the untangling of vcpu-id and
> > > > apic-id for x86, is that using vcpu-id is preferred, unless of course
> > > > the device expects an apic-id/mpidr, in which case there's no reason to
> > > > translate it on both sides.
> > > > 
> > > 
> > > I'm fairly strongly convinced that we should use the full 32-bit
> > > compressed MPIDR for everything ARM related going forward, as this will
> > > cover any case required and leverages and architecturally defined way of
> > > uniquely identifying a (v)CPU.
> > 
> > +1.
> > 
> > vcpu_ids, indexes or any other constructs are just a bunch
> > of KVM-specific definitions that do not describe the VM from an
> > architecture PoV. In contrast, the MPIDR is guaranteed to be unique
> > stable, and identifies a given (v)CPU.
> >
> 
> cpu-cpu and cpu-device interfaces should certainly use MPIDR, if they do
> in real hardware, to allow us to match emulation code to specs and keep
> sanity. But I assume those are the only places of "everything" you guys
> are referring to, as everywhere else we should stick to using the concept
> of vcpu-ids/indices. Since vcpu-indices are just counters they keep us
> from needing all the data structures to be large, complex, sparse things.
> Identifiers separate from MPIDR also allow hotunplug/plug to more easily
> reuse resources, i.e. remap indices to other vcpus as necessary.

Are vcpu ids already exposed to userspace (beyond the stupid
KVM_IRQ_LINE) ioctl and as such we're bound to whatever upper limit and
format they have?

If not, I think decoupling an internal ID and uniquely identifying a CPU
is a good idea.

> 
> In the PMU case above it seems better to use a vcpu-index. KVM and KVM's
> userspace both have unique vcpu-indices and unique MPIDRs per vcpu. The
> use here isn't based on a hardware spec, so there's nowhere to look for
> how MPIDR should/shouldn't be used. This is just a KVM spec. Here we might
> as well use the easiest to use unique identifier.

I think the only things that should matter here are (in no particular
order):
 - Userspace convenience
 - Clarity
 - Avoiding ambiguity

> 
> That said, I like the vcpu ioctl method much better. With that we avoid
> the need for vcpu identifiers all together. I'm even having third
> thoughts about the gic per vcpu registers. If we go with extending
> GET/SET_DEVICE_ATTR here, then I think we should do the same there as
> well. That would then leave only KVM_IRQ_LINE using a vcpu-index, which,
> with its 8-bit vcpu-index, we've outgrown for gicv3 machine types already
> anyway.
> 
For the GIC, I think we've discussed this in the past.  It really
depends whether you think about the GIC as one device (the distributor)
separate from the CPUs, with a bunch of separate devices attached to
each CPU and wired together somehow, or if you think of this as one big
coherent thing where parts of the device are specific to each CPU.

I tend to interpret the GIC as the latter and I think the kernel and
userspace implementations are also done that way, suggesting we should
stick with the device API for all GIC-related state (as was also the
suggestion for the GICv3 save/restore API).

Similarly, because the GIC architecture refers to CPUs using the MPIDR,
we should do the same in this interface.  Otherwise, I think you have to
define stricly how the exposed VCPU ID maps to an MPIDR somehow.

-Christoffer