[PATCH] i2c: rk3x: init module as subsys call

[Heiko Stuebner]

Hi Tao,

Am Dienstag, 5. Januar 2016, 15:42:32 schrieb Huang, Tao:
> On 2016年01月05日 15:02, Heiko Stuebner wrote:
> > Hi Jianqun,
> > 
> > Am Dienstag, 5. Januar 2016, 11:02:18 schrieb jianqun.xu:
> >> From: Xu Jianqun <jay.xu at rock-chips.com>
> >> 
> >> There is a requirement from pmic device, which is on the i2c bus,
> >> that the pmic needs to be called earlier then devices powered by
> >> the outputs of the pmic, if not, the devices maybe fail to probe.
> >> 
> >> For example, a pmic on i2c0, and touchscreen device on i2c2,
> >> i2c0: - pmic(rk818)
> >> i2c2: - ts(gt911), powered by rk818 on i2c0
> >> 
> >> The problem will happen if the i2c2 node in dts file is ordered
> >> before i2c0 node, then ts(gt911) will be probed before pmic(rk818),
> >> since the power from the pmic(rk818) for ts(gt911) hasn't enabled,
> >> so ts(gt911) will fail to probe due to the failure of i2c test.
> >> 
> >> But if we set the i2c0 node before i2c2, there is no this issue.
> >> 
> >> The stable way to make sure that pmic can be intalized before other
> >> peripher devices is to make the pmic module be subsys call, the i2c
> >> module need to be subsys call firstly.
> > 
> > I do believe that came up in the past already and the direction from
> > then
> > was (and most likely still is) that drivers should make use of the
> > probe-
> > deferral mechanism instead of wiggling with the initcall ordering.
> 
> I don't think this is a good idea. This will trigger a lots of init call
> failed. Before pmic init, all i2c device driver transmit will failed,
> and because i2c is slow bus, and i2c transmit may failed by other
> reasons, so the i2c driver and i2c device driver will try many times to
> make sure the transmit completion. These unnecessary transmission will
> make Linux boot very slow.

In general, the slowdown won't be _this_ much if touchscreen drivers need 
one deferral-round before i2c is available. I'm also only pointing out 
things I remember from the last time this came up. 

rk3x-i2c even was here already:
http://www.spinics.net/lists/linux-i2c/msg16680.html


> I2C bus should be subsys, and we can easy resolve this problem, why we
> depends on a complicated and slow implementation?

because it's the only safe way to do that. Because now you need i2c-init at 
subsys-init time, some months later some other soc may need some other 
ordering, especially needing i2c-init later/earlier.

Going through the deferral mechanism is the only way currently available to 
actually make this work on all socs.

Tomeu from Collabora is working on some better scheme to optimize device 
probing order but it looks like this may be a bit off still.


> > Your touchscreen will have a "xyz-supply" property and I think the
> > regulator-framework should already emit a -EPROBE_DEFER at
> > regulator_get,
> > when the regulator is specified but not available yet.
> 
> Unfortunately, mostly driver do not support regulator api. They are
> suppose power is on.

Having touchscreen drivers support its proper supply-regulators is not 
rocket science ;-) [0] , so I would consider this a bug in the touchscreen 
driver itself.

Just look into the datasheet and add the appropriate supplies to the drivers 
in question.


Heiko

[0] citiing my own work: 
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/tree/drivers/input/touchscreen/zforce_ts.c#n806

> 
> Thanks.
> Huang, Tao
> 
> > Heiko
> > 
> >> Signed-off-by: Xu Jianqun <jay.xu at rock-chips.com>
> >> ---
> >> 
> >>  drivers/i2c/busses/i2c-rk3x.c | 12 +++++++++++-
> >>  1 file changed, 11 insertions(+), 1 deletion(-)
> >> 
> >> diff --git a/drivers/i2c/busses/i2c-rk3x.c
> >> b/drivers/i2c/busses/i2c-rk3x.c index c1935eb..00e5959 100644
> >> --- a/drivers/i2c/busses/i2c-rk3x.c
> >> +++ b/drivers/i2c/busses/i2c-rk3x.c
> >> @@ -1037,7 +1037,17 @@ static struct platform_driver rk3x_i2c_driver =
> >> {
> >> 
> >>  	},
> >>  
> >>  };
> >> 
> >> -module_platform_driver(rk3x_i2c_driver);
> >> +static int __init rk3x_i2c_init(void)
> >> +{
> >> +	return platform_driver_register(&rk3x_i2c_driver);
> >> +}
> >> +subsys_initcall(rk3x_i2c_init);
> >> +
> >> +static void __exit rk3x_i2c_exit(void)
> >> +{
> >> +	platform_driver_unregister(&rk3x_i2c_driver);
> >> +}
> >> +module_exit(rk3x_i2c_exit);
> >> 
> >>  MODULE_DESCRIPTION("Rockchip RK3xxx I2C Bus driver");
> >>  MODULE_AUTHOR("Max Schwarz <max.schwarz at online.de>");