Add a struct device * member to the private driver data and use
it to print messages using dev_* functions rather than pr_*.
Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
---
drivers/spi/spi-imx.c | 27 ++++++++++++---------------
1 file changed, 12 insertions(+), 15 deletions(-)
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index 08492d6..7904d45 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -86,6 +86,7 @@ struct spi_imx_devtype_data {
struct spi_imx_data {
struct spi_bitbang bitbang;
+ struct device *dev;
struct completion xfer_done;
void __iomem *base;
@@ -250,14 +251,15 @@ static bool spi_imx_can_dma(struct spi_master *master, struct spi_device *spi,
#define MX51_ECSPI_TESTREG_LBC BIT(31)
/* MX51 eCSPI */
-static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi,
- unsigned int *fres)
+static unsigned int mx51_ecspi_clkdiv(struct spi_imx_data *spi_imx,
+ unsigned int fspi, unsigned int *fres)
{
/*
* there are two 4-bit dividers, the pre-divider divides by
* $pre, the post-divider by 2^$post
*/
unsigned int pre, post;
+ unsigned int fin = spi_imx->spi_clk;
if (unlikely(fspi > fin))
return 0;
@@ -270,14 +272,14 @@ static unsigned int mx51_ecspi_clkdiv(unsigned int fin, unsigned int fspi,
post = max(4U, post) - 4;
if (unlikely(post > 0xf)) {
- pr_err("%s: cannot set clock freq: %u (base freq: %u)\n",
- __func__, fspi, fin);
+ dev_err(spi_imx->dev, "cannot set clock freq: %u (base freq: %u)\n",
+ fspi, fin);
return 0xff;
}
pre = DIV_ROUND_UP(fin, fspi << post) - 1;
- pr_debug("%s: fin: %u, fspi: %u, post: %u, pre: %u\n",
+ dev_dbg(spi_imx->dev, "%s: fin: %u, fspi: %u, post: %u, pre: %u\n",
__func__, fin, fspi, post, pre);
/* Resulting frequency for the SCLK line. */
@@ -330,7 +332,7 @@ static int __maybe_unused mx51_ecspi_config(struct spi_imx_data *spi_imx,
ctrl |= MX51_ECSPI_CTRL_MODE_MASK;
/* set clock speed */
- ctrl |= mx51_ecspi_clkdiv(spi_imx->spi_clk, config->speed_hz, &clk);
+ ctrl |= mx51_ecspi_clkdiv(spi_imx, config->speed_hz, &clk);
/* set chip select to use */
ctrl |= MX51_ECSPI_CTRL_CS(config->cs);
@@ -968,18 +970,14 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
timeout = wait_for_completion_timeout(&spi_imx->dma_tx_completion,
IMX_DMA_TIMEOUT);
if (!timeout) {
- pr_warn("%s %s: I/O Error in DMA TX\n",
- dev_driver_string(&master->dev),
- dev_name(&master->dev));
+ dev_err(spi_imx->dev, "I/O Error in DMA TX\n");
dmaengine_terminate_all(master->dma_tx);
dmaengine_terminate_all(master->dma_rx);
} else {
timeout = wait_for_completion_timeout(
&spi_imx->dma_rx_completion, IMX_DMA_TIMEOUT);
if (!timeout) {
- pr_warn("%s %s: I/O Error in DMA RX\n",
- dev_driver_string(&master->dev),
- dev_name(&master->dev));
+ dev_err(spi_imx->dev, "I/O Error in DMA RX\n");
spi_imx->devtype_data->reset(spi_imx);
dmaengine_terminate_all(master->dma_rx);
}
@@ -996,9 +994,7 @@ static int spi_imx_dma_transfer(struct spi_imx_data *spi_imx,
return ret;
no_dma:
- pr_warn_once("%s %s: DMA not available, falling back to PIO\n",
- dev_driver_string(&master->dev),
- dev_name(&master->dev));
+ dev_warn_once(spi_imx->dev, "DMA not available, falling back to PIO\n");
return -EAGAIN;
}
@@ -1128,6 +1124,7 @@ static int spi_imx_probe(struct platform_device *pdev)
spi_imx = spi_master_get_devdata(master);
spi_imx->bitbang.master = master;
+ spi_imx->dev = &pdev->dev;
spi_imx->devtype_data = of_id ? of_id->data :
(struct spi_imx_devtype_data *)pdev->id_entry->driver_data;
--
2.7.0