[PATCH 2/4] iommu/arm-smmu: Allow disabling unmatched stream bypass

[Robin Murphy]

On 09/02/16 14:06, Will Deacon wrote:
> Hi Robin,
>
> On Tue, Jan 26, 2016 at 06:06:35PM +0000, Robin Murphy wrote:
>> Borrow the disable_bypass parameter from the SMMUv3 driver as a handy
>> debugging/security feature so that unmatched stream IDs (i.e. devices
>> not attached to an IOMMU domain) may be configured to fault.
>>
>> Signed-off-by: Robin Murphy <robin.murphy at arm.com>
>> ---
>>   drivers/iommu/arm-smmu.c | 32 +++++++++++++++++++++++---------
>>   1 file changed, 23 insertions(+), 9 deletions(-)
>>
>> diff --git a/drivers/iommu/arm-smmu.c b/drivers/iommu/arm-smmu.c
>> index 1f9093d..d1b7dc1 100644
>> --- a/drivers/iommu/arm-smmu.c
>> +++ b/drivers/iommu/arm-smmu.c
>> @@ -141,6 +141,8 @@
>>   #define ID2_PTFS_16K			(1 << 13)
>>   #define ID2_PTFS_64K			(1 << 14)
>>
>> +#define sGFSR_USF			(1 << 1)
>> +
>>   /* Global TLB invalidation */
>>   #define ARM_SMMU_GR0_TLBIVMID		0x64
>>   #define ARM_SMMU_GR0_TLBIALLNSNH	0x68
>> @@ -263,6 +265,10 @@ static int force_stage;
>>   module_param_named(force_stage, force_stage, int, S_IRUGO);
>>   MODULE_PARM_DESC(force_stage,
>>   	"Force SMMU mappings to be installed at a particular stage of translation. A value of '1' or '2' forces the corresponding stage. All other values are ignored (i.e. no stage is forced). Note that selecting a specific stage will disable support for nested translation.");
>> +static bool disable_bypass;
>> +module_param_named(disable_bypass, disable_bypass, bool, S_IRUGO);
>> +MODULE_PARM_DESC(disable_bypass,
>> +	"Disable bypass streams such that incoming transactions from devices that are not attached to an iommu domain will report an abort back to the device and will not be allowed to pass through the SMMU.");
>>
>>   enum arm_smmu_arch_version {
>>   	ARM_SMMU_V1 = 1,
>> @@ -704,8 +710,12 @@ static irqreturn_t arm_smmu_global_fault(int irq, void *dev)
>>   	if (!gfsr)
>>   		return IRQ_NONE;
>>
>> -	dev_err_ratelimited(smmu->dev,
>> -		"Unexpected global fault, this could be serious\n");
>> +	if (gfsr & sGFSR_USF)
>> +		dev_err_ratelimited(smmu->dev, "Unmatched stream fault: ID 0x%x\n",
>> +				    gfsynr1 & SMR_ID_MASK);
>> +	else
>
> I think I'd rather drop this message -- a global error is still indicative
> that something has gone horriby wrong, and we already print the gsynr
> registers below. Furthermore, if we take multiple faults, it might look
> like they're all exclusively due to unmatched streams.
>
> On top of that, I'm not convinced that USF will be set for an SMMU that
> doesn't implement stream-matching (because it will match an S2CR of type
> FAULT).

You're quite right, by the look of it the stream indexing case should 
report ICF rather than USF. My rationale for special-casing the message 
was that it's less of an "unexpected" fault when it's something you've 
specifically asked the driver for, but it also seems reasonable that 
someone turning on such an "I know what I'm doing" feature might be able 
to decode GFSR themselves. Considering the machinations of matching 
!MULTI and USF or ICF as appropriate just for the sake of printing a 
slightly reworded message, I'll drop this hunk.

> Other than that, looks good.

Thanks,
Robin.