[linux-sunxi][PATCH] ARM: dts: sun7i: Enable USB DRC on Itead Ibox

[Hans de Goede]

Hi,

On 08-02-16 16:59, codekipper at gmail.com wrote:
> From: Marcus Cooper <codekipper at gmail.com>
>
> Enable the otg/drc usb controller on the Itead Ibox device.
>
> Signed-off-by: Marcus Cooper <codekipper at gmail.com>

Same remark as with your Olimex A20 EVB board patch, please
also provide a vbus detect pin setting. If for some reason the
VBus detect is not wired up, or not working properly, please mention
this explicitly in the commit message.

Note that in some cases the axp209 is used for vbus detect,
rather then a gpio, see e.g. :

https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/sun7i-a20-bananapi.dts?id=dcfd8443d89f593e0c667a988ab017e716b33061

Regards,

Hans



> ---
>   arch/arm/boot/dts/sun7i-a20-itead-ibox.dts     | 14 ++++++++++++++
>   arch/arm/boot/dts/sunxi-itead-core-common.dtsi |  9 +++++++++
>   2 files changed, 23 insertions(+)
>
> diff --git a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
> index 661c21d..a512581 100644
> --- a/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
> +++ b/arch/arm/boot/dts/sun7i-a20-itead-ibox.dts
> @@ -118,8 +118,22 @@
>   		allwinner,drive = <SUN4I_PINCTRL_20_MA>;
>   		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>   	};
> +
> +	usb0_id_detect_pin: usb0_id_detect_pin at 0 {
> +		allwinner,pins = "PH4";
> +		allwinner,function = "gpio_in";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
>   };
>
>   &reg_ahci_5v {
>   	status = "okay";
>   };
> +
> +&usbphy {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&usb0_id_detect_pin>;
> +	usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
> +	status = "okay";
> +};
> diff --git a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi b/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
> index 2565d51..d22eea3 100644
> --- a/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
> +++ b/arch/arm/boot/dts/sunxi-itead-core-common.dtsi
> @@ -88,6 +88,10 @@
>   	status = "okay";
>   };
>
> +&otg_sram {
> +	status = "okay";
> +};
> +
>   #include "axp209.dtsi"
>
>   &reg_dcdc2 {
> @@ -129,6 +133,11 @@
>   	status = "okay";
>   };
>
> +&usb_otg {
> +	dr_mode = "otg";
> +	status = "okay";
> +};
> +
>   &usbphy {
>   	usb1_vbus-supply = <&reg_usb1_vbus>;
>   	usb2_vbus-supply = <&reg_usb2_vbus>;
>