[linux-sunxi] [PATCH 10/11] arm64: dts: add Allwinner A64 SoC .dtsi
Andre Przywara
andre.przywara at arm.com
Tue Feb 2 08:46:31 PST 2016
Hi Jens,
thanks for having such an elaborate look!
On 02/02/16 16:24, Jens Kuske wrote:
> Hi,
>
> On 01/02/16 18:39, Andre Przywara wrote:
>> The Allwinner A64 SoC is low-cost SoC with 4 ARM Cortex-A53 cores
>> and the typical tablet / TV box peripherals.
>> The Soc is based on the (32-bit) Allwinner H3 chip, sharing most of
>> the peripherals and the memory map.
>> Although the cores are proper 64-bit ones, the whole SoC is actually
>> limited to 4GB (including all the supported DRAM), so we use 32-bit
>> address and size cells. This has the nice feature of us being able to
>> reuse the DT for 32-bit kernels as well.
>> This .dtsi lists the hardware that we support so far.
>>
>> Signed-off-by: Andre Przywara <andre.przywara at arm.com>
>> ---
>> Documentation/devicetree/bindings/arm/sunxi.txt | 1 +
>> Documentation/devicetree/bindings/clock/sunxi.txt | 1 +
>> arch/arm64/boot/dts/allwinner/a64.dtsi | 583 ++++++++++++++++++++++
>> 3 files changed, 585 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/allwinner/a64.dtsi
>>
>> diff --git a/Documentation/devicetree/bindings/arm/sunxi.txt b/Documentation/devicetree/bindings/arm/sunxi.txt
>> index 980e065..4a83853 100644
>> --- a/Documentation/devicetree/bindings/arm/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/arm/sunxi.txt
>> @@ -14,6 +14,7 @@ using one of the following compatible strings:
>> allwinner,sun8i-a83t
>> allwinner,sun8i-h3
>> allwinner,sun9i-a80
>> + allwinner,a64
>>
>> For Allwinner SoCs without any specific needs the generic fallback value of:
>> allwinner,sunxi
>> diff --git a/Documentation/devicetree/bindings/clock/sunxi.txt b/Documentation/devicetree/bindings/clock/sunxi.txt
>> index e59f57b..44b0c6c 100644
>> --- a/Documentation/devicetree/bindings/clock/sunxi.txt
>> +++ b/Documentation/devicetree/bindings/clock/sunxi.txt
>> @@ -77,6 +77,7 @@ Required properties:
>> "allwinner,sun9i-a80-usb-mod-clk" - for usb gates + resets on A80
>> "allwinner,sun9i-a80-usb-phy-clk" - for usb phy gates + resets on A80
>> "allwinner,sun4i-a10-ve-clk" - for the Video Engine clock
>> + "allwinner,a64-bus-gates-clk" - for the A64 multi-parent bus gates clock
>>
>> Required properties for all clocks:
>> - reg : shall be the control register address for the clock.
>> diff --git a/arch/arm64/boot/dts/allwinner/a64.dtsi b/arch/arm64/boot/dts/allwinner/a64.dtsi
>> new file mode 100644
>> index 0000000..8dce10f
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/allwinner/a64.dtsi
>> @@ -0,0 +1,583 @@
>> +/*
>> + * Copyright (C) 2016 ARM Ltd.
>> + * based on the Allwinner H3 dtsi:
>> + * Copyright (C) 2015 Jens Kuske <jenskuske at gmail.com>
>> + *
>> + * This file is dual-licensed: you can use it either under the terms
>> + * of the GPL or the X11 license, at your option. Note that this dual
>> + * licensing only applies to this file, and not this project as a
>> + * whole.
>> + *
>> + * a) This file is free software; you can redistribute it and/or
>> + * modify it under the terms of the GNU General Public License as
>> + * published by the Free Software Foundation; either version 2 of the
>> + * License, or (at your option) any later version.
>> + *
>> + * This file is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * Or, alternatively,
>> + *
>> + * b) Permission is hereby granted, free of charge, to any person
>> + * obtaining a copy of this software and associated documentation
>> + * files (the "Software"), to deal in the Software without
>> + * restriction, including without limitation the rights to use,
>> + * copy, modify, merge, publish, distribute, sublicense, and/or
>> + * sell copies of the Software, and to permit persons to whom the
>> + * Software is furnished to do so, subject to the following
>> + * conditions:
>> + *
>> + * The above copyright notice and this permission notice shall be
>> + * included in all copies or substantial portions of the Software.
>> + *
>> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
>> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
>> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
>> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
>> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
>> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
>> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
>> + * OTHER DEALINGS IN THE SOFTWARE.
>> + */
>> +
>> +#include <dt-bindings/interrupt-controller/arm-gic.h>
>> +#include <dt-bindings/pinctrl/sun4i-a10.h>
>> +
>> +/ {
>> + compatible = "allwinner,a64", "allwinner,sunxi";
>> + interrupt-parent = <&gic>;
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> +
>> + aliases {
>> + serial0 = &uart0;
>> + serial1 = &uart1;
>> + serial2 = &uart2;
>> + serial3 = &uart3;
>> + serial4 = &uart4;
>> + };
>> +
>> + cpus {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + cpu at 0 {
>> + compatible = "arm,cortex-a53", "arm,armv8";
>> + device_type = "cpu";
>> + reg = <0>;
>> + enable-method = "psci";
>> + };
>> +
>> + cpu at 1 {
>> + compatible = "arm,cortex-a53", "arm,armv8";
>> + device_type = "cpu";
>> + reg = <1>;
>> + enable-method = "psci";
>> + };
>> +
>> + cpu at 2 {
>> + compatible = "arm,cortex-a53", "arm,armv8";
>> + device_type = "cpu";
>> + reg = <2>;
>> + enable-method = "psci";
>> + };
>> +
>> + cpu at 3 {
>> + compatible = "arm,cortex-a53", "arm,armv8";
>> + device_type = "cpu";
>> + reg = <3>;
>> + enable-method = "psci";
>> + };
>> + };
>> +
>> + psci {
>> + compatible = "arm,psci-0.2", "arm,psci";
>> + method = "smc";
>> + cpu_suspend = <0xc4000001>;
>> + cpu_off = <0x84000002>;
>> + cpu_on = <0xc4000003>;
>> + };
>> +
>> + memory {
>> + device_type = "memory";
>> + reg = <0x40000000 0>;
>> + };
>> +
>> + timer {
>> + compatible = "arm,armv8-timer";
>> + interrupts = <GIC_PPI 13
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> + <GIC_PPI 14
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> + <GIC_PPI 11
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
>> + <GIC_PPI 10
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> + };
>> +
>> + clocks {
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + osc24M: osc24M_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <24000000>;
>> + clock-output-names = "osc24M";
>> + };
>> +
>> + osc32k: osc32k_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <32768>;
>> + clock-output-names = "osc32k";
>> + };
>> +
>> + pll1: clk at 01c20000 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun8i-a23-pll1-clk";
>> + reg = <0x01c20000 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "pll1";
>> + };
>> +
>> + pll6: clk at 01c20028 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-pll6-clk";
>> + reg = <0x01c20028 0x4>;
>> + clocks = <&osc24M>;
>> + clock-output-names = "pll6", "pll6x2";
>> + };
>> +
>> + pll6d2: pll6d2_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-factor-clock";
>> + clock-div = <2>;
>> + clock-mult = <1>;
>> + clocks = <&pll6 0>;
>> + clock-output-names = "pll6d2";
>> + };
>> +
>> + /* dummy clock until pll6 can be reused */
>> + pll8: pll8_clk {
>> + #clock-cells = <0>;
>> + compatible = "fixed-clock";
>> + clock-frequency = <1>;
>> + clock-output-names = "pll8";
>> + };
Since I have you (as the original author ;-) in the loop: What was again
the reason for this dummy clock? Can't it be modelled with the existing
clock drivers in Linux?
>> +
>> + cpu: cpu_clk at 01c20050 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-cpu-clk";
>> + reg = <0x01c20050 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>;
>> + clock-output-names = "cpu";
>> + critical-clocks = <0>;
>> + };
>> +
>> + axi: axi_clk at 01c20050 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-axi-clk";
>> + reg = <0x01c20050 0x4>;
>> + clocks = <&cpu>;
>> + clock-output-names = "axi";
>> + };
>> +
>> + ahb1: ahb1_clk at 01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun6i-a31-ahb1-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6 0>;
>> + clock-output-names = "ahb1";
>> + };
>> +
>> + ahb2: ahb2_clk at 01c2005c {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun8i-h3-ahb2-clk";
>> + reg = <0x01c2005c 0x4>;
>> + clocks = <&ahb1>, <&pll6d2>;
>> + clock-output-names = "ahb2";
>> + };
>> +
>> + apb1: apb1_clk at 01c20054 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-apb0-clk";
>> + reg = <0x01c20054 0x4>;
>> + clocks = <&ahb1>;
>> + clock-output-names = "apb1";
>> + };
>> +
>> + apb2: apb2_clk at 01c20058 {
>> + #clock-cells = <0>;
>> + compatible = "allwinner,sun4i-a10-apb1-clk";
>> + reg = <0x01c20058 0x4>;
>> + clocks = <&osc32k>, <&osc24M>, <&pll6 1>, <&pll6 1>;
>> + clock-output-names = "apb2";
>> + };
>> +
>> + bus_gates: clk at 01c20060 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,a64-bus-gates-clk",
>> + "allwinner,sunxi-multi-bus-gates-clk";
>> + reg = <0x01c20060 0x14>;
>> + ahb1_parent {
>> + clocks = <&ahb1>;
>> + clock-indices = <1>, <5>,
>> + <6>, <8>,
>> + <9>, <10>,
>> + <13>, <14>,
>> + <18>, <19>,
>> + <20>, <21>,
>> + <23>, <24>,
>> + <25>, <28>,
>> + <32>, <35>,
>> + <36>, <37>,
>> + <40>, <43>,
>> + <44>, <52>,
>> + <53>, <54>,
>> + <135>;
>> + clock-output-names = "bus_mipidsi", "bus_ce",
>> + "bus_dma", "bus_mmc0",
>> + "bus_mmc1", "bus_mmc2",
>> + "bus_nand", "bus_sdram",
>> + "bus_ts", "bus_hstimer",
>> + "bus_spi0", "bus_spi1",
>> + "bus_otg", "bus_otg_ehci0",
>> + "bus_ehci0", "bus_otg_ohci0",
>> + "bus_ve", "bus_lcd0",
>> + "bus_lcd1", "bus_deint",
>> + "bus_csi", "bus_hdmi",
>> + "bus_de", "bus_gpu",
>> + "bus_msgbox", "bus_spinlock",
>> + "bus_dbg";
>> + };
>> + ahb2_parent {
>> + clocks = <&ahb2>;
>> + clock-indices = <17>, <29>;
>> + clock-output-names = "bus_gmac", "bus_ohci0";
>> + };
>> + apb1_parent {
>> + clocks = <&apb1>;
>> + clock-indices = <64>, <65>,
>> + <69>, <72>,
>> + <76>, <77>,
>> + <78>;
>> + clock-output-names = "bus_codec", "bus_spdif",
>> + "bus_pio", "bus_ths",
>> + "bus_i2s0", "bus_i2s1",
>> + "bus_i2s2";
>> + };
>> + abp2_parent {
>> + clocks = <&apb2>;
>> + clock-indices = <96>, <97>,
>> + <98>, <101>,
>> + <112>, <113>,
>> + <114>, <115>,
>> + <116>;
>> + clock-output-names = "bus_i2c0", "bus_i2c1",
>> + "bus_i2c2", "bus_scr",
>> + "bus_uart0", "bus_uart1",
>> + "bus_uart2", "bus_uart3",
>> + "bus_uart4";
>> + };
>> + };
>> +
>> + mmc0_clk: clk at 01c20088 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun4i-a10-mmc-clk";
>
> The A64 MMC clocks don't seem to be fully compatible to A10. The output
> and sample phase control has been moved to the MMC module itself.
> The dividers are the same, but the additional special "outputs" are gone.
So from comparing the H3 and the A64 datasheet I see that this is one of
the rare deviations of the A64 from the H3?
>> + reg = <0x01c20088 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>
> Parents are PLL6(2x) and PLL8(2x) according to manual.
Indeed, thanks for pointing this out! So do we need a proper pll8 clock?
>
>> + clock-output-names = "mmc0",
>> + "mmc0_output",
>> + "mmc0_sample";
>> + };
>> +
>> + mmc1_clk: clk at 01c2008c {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun4i-a10-mmc-clk";
>> + reg = <0x01c2008c 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> + clock-output-names = "mmc1",
>> + "mmc1_output",
>> + "mmc1_sample";
>> + };
>> +
>> + mmc2_clk: clk at 01c20090 {
>> + #clock-cells = <1>;
>> + compatible = "allwinner,sun4i-a10-mmc-clk";
>> + reg = <0x01c20090 0x4>;
>> + clocks = <&osc24M>, <&pll6 0>, <&pll8>;
>> + clock-output-names = "mmc2",
>> + "mmc2_output",
>> + "mmc2_sample";
>> + };
>> + };
>> +
>> + regulators {
>> + reg_vcc3v3: vcc3v3 {
>> + compatible = "regulator-fixed";
>> + regulator-name = "vcc3v3";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + };
>> + };
>> +
>> + soc {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges;
>> +
>> + mmc0: mmc at 01c0f000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c0f000 0x1000>;
>> + clocks = <&bus_gates 8>,
>> + <&mmc0_clk 0>,
>
> Consequently, the MMC driver now has to control the output/sample phase
> with registers 0x140-0x148 instead of
>> + <&mmc0_clk 1>,
>> + <&mmc0_clk 2>;
OK, good point. I was just briefly browsing over the register
descriptions and missed that.
So it looks like I need to change the driver. Interestingly it seems to
work anyways ...
> And there seems to be some new clock divider somewhere which I haven't
> found in the manual yet. The clock measured at the CLK pin is always
> half the expected rate (even with 24MHz as MMC clock parent, so no
> PLL6*2 problem).
Mmh, I heard about that mysterious clock doubling / halving already. Was
that actually causing any issues?
>
>> + clock-names = "ahb",
>> + "mmc",
>> + "output",
>> + "sample";
>> + resets = <&ahb_rst 8>;
>> + reset-names = "ahb";
>> + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + mmc1: mmc at 01c10000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c10000 0x1000>;
>> + clocks = <&bus_gates 9>,
>> + <&mmc1_clk 0>,
>> + <&mmc1_clk 1>,
>> + <&mmc1_clk 2>;
>> + clock-names = "ahb",
>> + "mmc",
>> + "output",
>> + "sample";
>> + resets = <&ahb_rst 9>;
>> + reset-names = "ahb";
>> + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + mmc2: mmc at 01c11000 {
>> + compatible = "allwinner,sun5i-a13-mmc";
>> + reg = <0x01c11000 0x1000>;
>> + clocks = <&bus_gates 10>,
>> + <&mmc2_clk 0>,
>> + <&mmc2_clk 1>,
>> + <&mmc2_clk 2>;
>> + clock-names = "ahb",
>> + "mmc",
>> + "output",
>> + "sample";
>> + resets = <&ahb_rst 10>;
>> + reset-names = "ahb";
>> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
>> + status = "disabled";
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + };
>> +
>> + pio: pinctrl at 01c20800 {
>> + compatible = "allwinner,a64-pinctrl";
>> + reg = <0x01c20800 0x400>;
>> + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
>> + clocks = <&bus_gates 69>;
>> + gpio-controller;
>> + #gpio-cells = <3>;
>> + interrupt-controller;
>> + #interrupt-cells = <2>;
>> +
>> + uart0_pins_a: uart0 at 0 {
>> + allwinner,pins = "PB8", "PB9";
>> + allwinner,function = "uart0";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + uart0_pins_b: uart0 at 1 {
>> + allwinner,pins = "PF2", "PF3";
>> + allwinner,function = "uart0";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + uart1_pins: uart1 at 0 {
>> + allwinner,pins = "PG6", "PG7", "PG8", "PG9";
>> + allwinner,function = "uart1";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + uart2_pins: uart2 at 0 {
>> + allwinner,pins = "PB0", "PB1", "PB2", "PB3";
>> + allwinner,function = "uart2";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + uart3_pins_a: uart3 at 0 {
>> + allwinner,pins = "PD0", "PD1";
>> + allwinner,function = "uart3";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + uart3_pins_b: uart3 at 1 {
>> + allwinner,pins = "PH4", "PH5", "PH6", "PH7";
>> + allwinner,function = "uart3";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + uart4_pins: uart4 at 0 {
>> + allwinner,pins = "PD2", "PD3", "PD4", "PD5";
>> + allwinner,function = "uart4";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + mmc0_pins: mmc0 at 0 {
>> + allwinner,pins = "PF0", "PF1", "PF2", "PF3",
>> + "PF4", "PF5";
>> + allwinner,function = "mmc0";
>> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + mmc0_default_cd_pin: mmc0_cd_pin at 0 {
>> + allwinner,pins = "PF6";
>> + allwinner,function = "gpio_in";
>> + allwinner,drive = <SUN4I_PINCTRL_10_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
>> + };
>> +
>> + mmc1_pins: mmc1 at 0 {
>> + allwinner,pins = "PG0", "PG1", "PG2", "PG3",
>> + "PG4", "PG5";
>> + allwinner,function = "mmc1";
>> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> +
>> + mmc2_pins: mmc2 at 0 {
>> + allwinner,pins = "PC1", "PC5", "PC6", "PC8",
>> + "PC9", "PC10";
>> + allwinner,function = "mmc2";
>> + allwinner,drive = <SUN4I_PINCTRL_30_MA>;
>> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
>> + };
>> + };
>> +
>> + ahb_rst: reset at 01c202c0 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-ahb1-reset";
>> + reg = <0x01c202c0 0xc>;
>> + };
>> +
>> + apb1_rst: reset at 01c202d0 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + reg = <0x01c202d0 0x4>;
>> + };
>> +
>> + apb2_rst: reset at 01c202d8 {
>> + #reset-cells = <1>;
>> + compatible = "allwinner,sun6i-a31-clock-reset";
>> + reg = <0x01c202d8 0x4>;
>> + };
>> +
>> + uart0: serial at 01c28000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28000 0x400>;
>> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&bus_gates 112>;
>> + resets = <&apb2_rst 16>;
>> + reset-names = "apb2";
>
> Do we need reset-names here (and below)?
Probably not, in fact I was wondering about that already. Actually I
just copied them from some other DT ;-)
>> + status = "disabled";
>> + };
>> +
>> + uart1: serial at 01c28400 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28400 0x400>;
>> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&bus_gates 113>;
>> + resets = <&apb2_rst 17>;
>> + reset-names = "apb2";
>> + status = "disabled";
>> + };
>> +
>> + uart2: serial at 01c28800 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28800 0x400>;
>> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&bus_gates 114>;
>> + resets = <&apb2_rst 18>;
>> + reset-names = "apb2";
>> + status = "disabled";
>> + };
>> +
>> + uart3: serial at 01c28c00 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c28c00 0x400>;
>> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&bus_gates 115>;
>> + resets = <&apb2_rst 19>;
>> + reset-names = "apb2";
>> + status = "disabled";
>> + };
>> +
>> + uart4: serial at 01c29000 {
>> + compatible = "snps,dw-apb-uart";
>> + reg = <0x01c29000 0x400>;
>> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
>> + reg-shift = <2>;
>> + reg-io-width = <4>;
>> + clocks = <&bus_gates 116>;
>> + resets = <&apb2_rst 20>;
>> + reset-names = "apb2";
>> + status = "disabled";
>> + };
>> +
>> + rtc: rtc at 01f00000 {
>> + compatible = "allwinner,sun6i-a31-rtc";
>> + reg = <0x01f00000 0x54>;
>> + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
>> + <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
>> + };
>> + };
>> +
>> + gic: interrupt-controller@{
>> + compatible = "arm,gic-400";
>> + interrupt-controller;
>> + #interrupt-cells = <3>;
>> + #address-cells = <0>;
>> +
>> + reg = <0x01C81000 0x1000>,
>> + <0x01C82000 0x2000>,
>> + <0x01C84000 0x2000>,
>> + <0x01C86000 0x2000>;
>
> Maybe lowercase hex here too.
Yes.
Thanks for actually going through this!
Cheers,
Andre.
>> + interrupts = <GIC_PPI 9
>> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
>> + };
>> +};
>>
>
> Regards,
> Jens
>
More information about the linux-arm-kernel
mailing list