[PATCH] ARM: dts: imx6q-utilite-pro: enable 2nd display pipeline

Shawn Guo shawnguo at kernel.org
Fri Dec 30 06:27:11 PST 2016


On Fri, Dec 02, 2016 at 03:37:22PM +0100, christopher.spinrath at rwth-aachen.de wrote:
> From: Christopher Spinrath <christopher.spinrath at rwth-aachen.de>
> 
> Apart from the already enabled Designware HDMI port, the Utilite Pro
> has a second display pipeline which has the following shape:
> 
>   IPU1 DI0 --> Parallel display --> tfp410 rgb24 to DVI encoder
>                                 --> HDMI connector.
> Enable support for it.
> 
> In addition, since this pipeline is hardwired to IPU1, sever the link
> between IPU1 and the SoC-internal Designware HDMI encoder forcing the
> latter to be connected to IPU2 instead of IPU1. Otherwise, it is not
> possible to drive both displays at high resolution due to the bandwidth
> limitations of a single IPU.
> 
> Signed-off-by: Christopher Spinrath <christopher.spinrath at rwth-aachen.de>

@Philipp, can you help review the changes?

> ---
> 
> Hi all,
> 
> the removal of the link between IPU1 and the Designware HDMI encoder is the
> result of a discussion I had with Philipp Zabel:
> 
>   https://lists.freedesktop.org/archives/dri-devel/2016-November/125399.html .
> 
> Altough it is not possible to connect anything else to IPU1 on the Utilite, this
> approach has at least one disadvantage: if the resolution is low enough such 
> that a single IPU can handle both displays then muxing both displays to IPU1
> would reduce the power consumption.
> 
> However, IMHO omitting the link IPU1 <--> DW HDMI is still the preferrable
> solution since I'm not aware of any OS/driver that is capable of switching IPUs
> or can handle the bandwidth limitation in a sane way. In particular, Linux is
> unusable when both displays are supposed to be driven at high resolution and
> both muxing options for the DW HDMI are available (this is not a userspace
> issue; the system becomes almost unresponsive as soon as the kernel sets the
> initial resolution).
> 
> Cheers,
> Christopher
> 
> P.S.: this patch depends on the tfp410 bridge driver which has recently been
> merged into drm-next.

v4.10-rc1 has the driver, so the dependency is gone now, I guess.

> 
>  arch/arm/boot/dts/imx6q-utilite-pro.dts | 115 ++++++++++++++++++++++++++++++++
>  1 file changed, 115 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/imx6q-utilite-pro.dts b/arch/arm/boot/dts/imx6q-utilite-pro.dts
> index 2200994..69bdd82 100644
> --- a/arch/arm/boot/dts/imx6q-utilite-pro.dts
> +++ b/arch/arm/boot/dts/imx6q-utilite-pro.dts
> @@ -59,6 +59,33 @@
>  		rtc1 = &snvs_rtc;
>  	};
>  
> +	encoder {
> +		compatible = "ti,tfp410";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +
> +				tfp410_in: endpoint {
> +					remote-endpoint = <&parallel_display_out>;
> +				};
> +			};
> +
> +			port at 1 {
> +				reg = <1>;
> +
> +				tfp410_out: endpoint {
> +					remote-endpoint = <&hdmi_connector_in>;
> +				};
> +			};
> +		};
> +	};
> +
>  	gpio-keys {
>  		compatible = "gpio-keys";
>  		pinctrl-names = "default";
> @@ -72,6 +99,19 @@
>  		};
>  	};
>  
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +

The newline is unnecessary.

> +		type = "a";
> +		ddc-i2c-bus = <&i2c_dvi_ddc>;
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&tfp410_out>;
> +			};
> +		};
> +	};
> +
>  	i2cmux {
>  		compatible = "i2c-mux-gpio";
>  		pinctrl-names = "default";
> @@ -105,8 +145,46 @@
>  			#size-cells = <0>;
>  		};
>  	};
> +
> +	parallel-display {
> +		compatible = "fsl,imx-parallel-display";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_ipu1>;
> +

Ditto

I can fix them up if I get a Reviewed-by tag from Philipp on this
version.

Shawn

> +		interface-pix-fmt = "rgb24";
> +
> +		port at 0 {
> +			reg = <0>;
> +
> +			parallel_display_in: endpoint {
> +				remote-endpoint = <&ipu1_di0_disp0>;
> +			};
> +		};
> +
> +		port at 1 {
> +			reg = <1>;
> +
> +			parallel_display_out: endpoint {
> +				remote-endpoint = <&tfp410_in>;
> +			};
> +		};
> +	};
>  };
>  
> +/*
> + * A single IPU is not able to drive both display interfaces available on the
> + * Utilite Pro at high resolution due to its bandwidth limitation. Since the
> + * tfp410 encoder is wired up to IPU1, sever the link between IPU1 and the
> + * SoC-internal Designware HDMI encoder forcing the latter to be connected to
> + * IPU2 instead of IPU1.
> + */
> +/delete-node/&ipu1_di0_hdmi;
> +/delete-node/&hdmi_mux_0;
> +/delete-node/&ipu1_di1_hdmi;
> +/delete-node/&hdmi_mux_1;
> +
>  &hdmi {
>  	ddc-i2c-bus = <&i2c2>;
>  	status = "okay";
> @@ -151,6 +229,39 @@
>  		>;
>  	};
>  
> +	pinctrl_ipu1: ipu1grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x38
> +			MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15       0x38
> +			MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02        0x38
> +			MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03        0x38
> +			MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00   0x38
> +			MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01   0x38
> +			MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02   0x38
> +			MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03   0x38
> +			MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04   0x38
> +			MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05   0x38
> +			MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06   0x38
> +			MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07   0x38
> +			MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08   0x38
> +			MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09   0x38
> +			MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10  0x38
> +			MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11  0x38
> +			MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12  0x38
> +			MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13  0x38
> +			MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14  0x38
> +			MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15  0x38
> +			MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16  0x38
> +			MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17  0x38
> +			MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18  0x38
> +			MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19  0x38
> +			MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20  0x38
> +			MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21  0x38
> +			MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22  0x38
> +			MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23  0x38
> +		>;
> +	};
> +
>  	pinctrl_uart2: uart2grp {
>  		fsl,pins = <
>  			MX6QDL_PAD_GPIO_7__UART2_TX_DATA 0x1b0b1
> @@ -194,6 +305,10 @@
>  	};
>  };
>  
> +&ipu1_di0_disp0 {
> +	remote-endpoint = <&parallel_display_in>;
> +};
> +
>  &pcie {
>  	pcie at 0,0 {
>  		reg = <0x000000 0 0 0 0>;
> -- 
> 2.10.2
> 



More information about the linux-arm-kernel mailing list