[PATCH v2 1/6] ARM: mach-mx31_3ds: Remove camera support
Fabio Estevam
festevam at gmail.com
Fri Dec 30 03:33:28 PST 2016
From: Fabio Estevam <fabio.estevam at nxp.com>
Since commit c93cc61475ebbe6e66 ("[media] staging/media: remove deprecated
mx3 driver") the mx3 camera driver has been removed, so remove the camera
support from the board file as well.
Signed-off-by: Fabio Estevam <fabio.estevam at nxp.com>
---
Changes since v1:
- Also remove CSI pins from IOMUX definition
arch/arm/mach-imx/mach-mx31_3ds.c | 160 --------------------------------------
1 file changed, 160 deletions(-)
diff --git a/arch/arm/mach-imx/mach-mx31_3ds.c b/arch/arm/mach-imx/mach-mx31_3ds.c
index 12b8a52..558e5f8 100644
--- a/arch/arm/mach-imx/mach-mx31_3ds.c
+++ b/arch/arm/mach-imx/mach-mx31_3ds.c
@@ -26,16 +26,12 @@
#include <linux/regulator/machine.h>
#include <linux/usb/otg.h>
#include <linux/usb/ulpi.h>
-#include <linux/memblock.h>
-
-#include <media/soc_camera.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/time.h>
#include <asm/memory.h>
#include <asm/mach/map.h>
-#include <asm/memblock.h>
#include "3ds_debugboard.h"
#include "common.h"
@@ -137,23 +133,6 @@ static int mx31_3ds_pins[] = {
MX31_PIN_HSYNC__HSYNC,
MX31_PIN_FPSHIFT__FPSHIFT,
MX31_PIN_CONTRAST__CONTRAST,
- /* CSI */
- MX31_PIN_CSI_D6__CSI_D6,
- MX31_PIN_CSI_D7__CSI_D7,
- MX31_PIN_CSI_D8__CSI_D8,
- MX31_PIN_CSI_D9__CSI_D9,
- MX31_PIN_CSI_D10__CSI_D10,
- MX31_PIN_CSI_D11__CSI_D11,
- MX31_PIN_CSI_D12__CSI_D12,
- MX31_PIN_CSI_D13__CSI_D13,
- MX31_PIN_CSI_D14__CSI_D14,
- MX31_PIN_CSI_D15__CSI_D15,
- MX31_PIN_CSI_HSYNC__CSI_HSYNC,
- MX31_PIN_CSI_MCLK__CSI_MCLK,
- MX31_PIN_CSI_PIXCLK__CSI_PIXCLK,
- MX31_PIN_CSI_VSYNC__CSI_VSYNC,
- MX31_PIN_CSI_D5__GPIO3_5, /* CMOS PWDN */
- IOMUX_MODE(MX31_PIN_RI_DTE1, IOMUX_CONFIG_GPIO), /* CMOS reset */
/* SSI */
MX31_PIN_STXD4__STXD4,
MX31_PIN_SRXD4__SRXD4,
@@ -162,98 +141,6 @@ static int mx31_3ds_pins[] = {
};
/*
- * Camera support
- */
-static phys_addr_t mx3_camera_base __initdata;
-#define MX31_3DS_CAMERA_BUF_SIZE SZ_8M
-
-#define MX31_3DS_GPIO_CAMERA_PW IOMUX_TO_GPIO(MX31_PIN_CSI_D5)
-#define MX31_3DS_GPIO_CAMERA_RST IOMUX_TO_GPIO(MX31_PIN_RI_DTE1)
-
-static struct gpio mx31_3ds_camera_gpios[] = {
- { MX31_3DS_GPIO_CAMERA_PW, GPIOF_OUT_INIT_HIGH, "camera-power" },
- { MX31_3DS_GPIO_CAMERA_RST, GPIOF_OUT_INIT_HIGH, "camera-reset" },
-};
-
-static const struct mx3_camera_pdata mx31_3ds_camera_pdata __initconst = {
- .flags = MX3_CAMERA_DATAWIDTH_10,
- .mclk_10khz = 2600,
-};
-
-static int __init mx31_3ds_init_camera(void)
-{
- int dma, ret = -ENOMEM;
- struct platform_device *pdev =
- imx31_alloc_mx3_camera(&mx31_3ds_camera_pdata);
-
- if (IS_ERR(pdev))
- return PTR_ERR(pdev);
-
- if (!mx3_camera_base)
- goto err;
-
- dma = dma_declare_coherent_memory(&pdev->dev,
- mx3_camera_base, mx3_camera_base,
- MX31_3DS_CAMERA_BUF_SIZE,
- DMA_MEMORY_MAP | DMA_MEMORY_EXCLUSIVE);
-
- if (!(dma & DMA_MEMORY_MAP))
- goto err;
-
- ret = platform_device_add(pdev);
- if (ret)
-err:
- platform_device_put(pdev);
-
- return ret;
-}
-
-static int mx31_3ds_camera_power(struct device *dev, int on)
-{
- /* enable or disable the camera */
- pr_debug("%s: %s the camera\n", __func__, on ? "ENABLE" : "DISABLE");
- gpio_set_value(MX31_3DS_GPIO_CAMERA_PW, on ? 0 : 1);
-
- if (!on)
- goto out;
-
- /* If enabled, give a reset impulse */
- gpio_set_value(MX31_3DS_GPIO_CAMERA_RST, 0);
- msleep(20);
- gpio_set_value(MX31_3DS_GPIO_CAMERA_RST, 1);
- msleep(100);
-
-out:
- return 0;
-}
-
-static struct i2c_board_info mx31_3ds_i2c_camera = {
- I2C_BOARD_INFO("ov2640", 0x30),
-};
-
-static struct regulator_bulk_data mx31_3ds_camera_regs[] = {
- { .supply = "cmos_vcore" },
- { .supply = "cmos_2v8" },
-};
-
-static struct soc_camera_link iclink_ov2640 = {
- .bus_id = 0,
- .board_info = &mx31_3ds_i2c_camera,
- .i2c_adapter_id = 0,
- .power = mx31_3ds_camera_power,
- .regulators = mx31_3ds_camera_regs,
- .num_regulators = ARRAY_SIZE(mx31_3ds_camera_regs),
-};
-
-static struct platform_device mx31_3ds_ov2640 = {
- .name = "soc-camera-pdrv",
- .id = 0,
- .dev = {
- .platform_data = &iclink_ov2640,
- },
-};
-
-/*
* FB support
*/
static const struct fb_videomode fb_modedb[] = {
@@ -410,7 +297,6 @@ static struct regulator_init_data vmmc2_init = {
static struct regulator_consumer_supply vmmc1_consumers[] = {
REGULATOR_SUPPLY("vcore", "spi0.0"),
- REGULATOR_SUPPLY("cmos_2v8", "soc-camera-pdrv.0"),
};
static struct regulator_init_data vmmc1_init = {
@@ -441,22 +327,6 @@ static struct regulator_init_data vgen_init = {
.consumer_supplies = vgen_consumers,
};
-static struct regulator_consumer_supply vvib_consumers[] = {
- REGULATOR_SUPPLY("cmos_vcore", "soc-camera-pdrv.0"),
-};
-
-static struct regulator_init_data vvib_init = {
- .constraints = {
- .min_uV = 1300000,
- .max_uV = 1300000,
- .apply_uV = 1,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE |
- REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(vvib_consumers),
- .consumer_supplies = vvib_consumers,
-};
-
static struct mc13xxx_regulator_init_data mx31_3ds_regulators[] = {
{
.id = MC13783_REG_PWGT1SPI, /* Power Gate for ARM core. */
@@ -480,9 +350,6 @@ static struct mc13xxx_regulator_init_data mx31_3ds_regulators[] = {
}, {
.id = MC13783_REG_VGEN, /* Power LCD */
.init_data = &vgen_init,
- }, {
- .id = MC13783_REG_VVIB, /* Power CMOS */
- .init_data = &vvib_init,
},
};
@@ -688,10 +555,6 @@ static const struct imxi2c_platform_data mx31_3ds_i2c0_data __initconst = {
.bitrate = 100000,
};
-static struct platform_device *devices[] __initdata = {
- &mx31_3ds_ov2640,
-};
-
static void __init mx31_3ds_init(void)
{
imx31_soc_init();
@@ -723,14 +586,10 @@ static void __init mx31_3ds_init(void)
static void __init mx31_3ds_late(void)
{
- int ret;
-
mx31_3ds_spi_devs[0].irq = gpio_to_irq(IOMUX_TO_GPIO(MX31_PIN_GPIO1_3));
spi_register_board_info(mx31_3ds_spi_devs,
ARRAY_SIZE(mx31_3ds_spi_devs));
- platform_add_devices(devices, ARRAY_SIZE(devices));
-
mx31_3ds_usbotg_init();
if (otg_mode_host) {
otg_pdata.otg = imx_otg_ulpi_create(ULPI_OTG_DRVVBUS |
@@ -751,17 +610,6 @@ static void __init mx31_3ds_late(void)
"devices on the debug board are unusable.\n");
imx31_add_mxc_mmc(0, &sdhc1_pdata);
-
- /* CSI */
- /* Camera power: default - off */
- ret = gpio_request_array(mx31_3ds_camera_gpios,
- ARRAY_SIZE(mx31_3ds_camera_gpios));
- if (ret) {
- pr_err("Failed to request camera gpios");
- iclink_ov2640.power = NULL;
- }
-
- mx31_3ds_init_camera();
}
static void __init mx31_3ds_timer_init(void)
@@ -769,13 +617,6 @@ static void __init mx31_3ds_timer_init(void)
mx31_clocks_init(26000000);
}
-static void __init mx31_3ds_reserve(void)
-{
- /* reserve MX31_3DS_CAMERA_BUF_SIZE bytes for mx3-camera */
- mx3_camera_base = arm_memblock_steal(MX31_3DS_CAMERA_BUF_SIZE,
- MX31_3DS_CAMERA_BUF_SIZE);
-}
-
MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
/* Maintainer: Freescale Semiconductor, Inc. */
.atag_offset = 0x100,
@@ -785,6 +626,5 @@ MACHINE_START(MX31_3DS, "Freescale MX31PDK (3DS)")
.init_time = mx31_3ds_timer_init,
.init_machine = mx31_3ds_init,
.init_late = mx31_3ds_late,
- .reserve = mx31_3ds_reserve,
.restart = mxc_restart,
MACHINE_END
--
2.7.4
More information about the linux-arm-kernel
mailing list