[PATCH v2 08/12] ARM: dts: imx: Add imx6sll EVK board dts support
Bai Ping
ping.bai at nxp.com
Tue Dec 27 01:47:46 PST 2016
Add basic dts support for imx6sll EVK board.
Signed-off-by: Bai Ping <ping.bai at nxp.com>
---
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6sll-evk.dts | 474 ++++++++++++++++++++++++++++++++++++++
2 files changed, 476 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 38c595d..24eb4bd 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -416,6 +416,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
dtb-$(CONFIG_SOC_IMX6SL) += \
imx6sl-evk.dtb \
imx6sl-warp.dtb
+dtb-$(CONFIG_SOC_IMX6SLL) += \
+ imx6sll-evk.dtb
dtb-$(CONFIG_SOC_IMX6SX) += \
imx6sx-nitrogen6sx.dtb \
imx6sx-sabreauto.dtb \
diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts
new file mode 100644
index 0000000..7b8264b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sll-evk.dts
@@ -0,0 +1,474 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "imx6sll.dtsi"
+
+/ {
+ model = "Freescale i.MX6SLL EVK Board";
+ compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
+
+ memory {
+ reg = <0x80000000 0x80000000>;
+ };
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+
+ reg_usb_otg1_vbus: reg-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_usb_otg2_vbus: reg-usb-otg2-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg2_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_aud3v: reg-aud3v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-3v15";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3150000>;
+ regulator-boot-on;
+ };
+
+ reg_aud4v: reg-aud4v {
+ compatible = "regulator-fixed";
+ regulator-name = "wm8962-supply-4v2";
+ regulator-min-microvolt = <4325000>;
+ regulator-max-microvolt = <4325000>;
+ regulator-boot-on;
+ };
+
+ reg_lcd: reg-lcd {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-pwr";
+ gpio = <&gpio4 8 0>;
+ enable-active-high;
+ };
+
+ reg_sd1_vmmc: reg-sd1-vmmc {
+ compatible = "regulator-fixed";
+ regulator-name = "SD1_SPWR";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+};
+
+&cpu0 {
+ arm-supply = <&sw1a_reg>;
+ soc-supply = <&sw1c_reg>;
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic: pfuze100 at 08 {
+ compatible = "fsl,pfuze100";
+ reg = <0x08>;
+
+ regulators {
+ sw1a_reg: sw1ab {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw1c_reg: sw1c {
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1875000>;
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-ramp-delay = <6250>;
+ };
+
+ sw2_reg: sw2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3a_reg: sw3a {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw3b_reg: sw3b {
+ regulator-min-microvolt = <400000>;
+ regulator-max-microvolt = <1975000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ sw4_reg: sw4 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ swbst_reg: swbst {
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5150000>;
+ };
+
+ snvs_reg: vsnvs {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vref_reg: vrefddr {
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vgen1_reg: vgen1 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ regulator-always-on;
+ };
+
+ vgen2_reg: vgen2 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1550000>;
+ };
+
+ vgen3_reg: vgen3 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ vgen4_reg: vgen4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen5_reg: vgen5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vgen6_reg: vgen6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_hog>;
+
+ pinctrl_hog: hoggrp {
+ fsl,pins = <
+ MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 0x17059
+ MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22 0x17059
+ MX6SLL_PAD_KEY_COL3__GPIO3_IO30 0x17059
+ /*
+ * Must set the LVE of pad SD2_RESET, otherwise current
+ * leakage through eMMC chip will pull high the VCCQ to
+ * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch.
+ */
+ MX6SLL_PAD_SD2_RESET__GPIO4_IO27 0x417059
+ MX6SLL_PAD_KEY_COL4__GPIO4_IO00 0x17059
+ MX6SLL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059 /* SD3 CD */
+ MX6SLL_PAD_KEY_COL6__GPIO4_IO04 0x17059 /*SD3 RESET */
+ MX6SLL_PAD_KEY_COL5__GPIO4_IO02 0x17059
+ MX6SLL_PAD_GPIO4_IO24__GPIO4_IO24 0x17059 /* HP DETECT */
+ /* CHG_FLT, CHG_UOK/DOK, CHG_STATUS */
+ MX6SLL_PAD_ECSPI2_MISO__GPIO4_IO14 0x17000
+ MX6SLL_PAD_ECSPI2_MOSI__GPIO4_IO13 0x17000
+ MX6SLL_PAD_ECSPI2_SS0__GPIO4_IO15 0x17000
+ >;
+ };
+
+ pinctrl_audmux3: audmux3grp {
+ fsl,pins = <
+ MX6SLL_PAD_AUD_TXC__AUD3_TXC 0x4130b0
+ MX6SLL_PAD_AUD_TXFS__AUD3_TXFS 0x4130b0
+ MX6SLL_PAD_AUD_TXD__AUD3_TXD 0x4110b0
+ MX6SLL_PAD_AUD_RXD__AUD3_RXD 0x4130b0
+ MX6SLL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130b0
+ >;
+ };
+
+ pinctrl_csi1: csi1grp {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_GDRL__CSI_MCLK 0x1b088
+ MX6SLL_PAD_EPDC_GDCLK__CSI_PIXCLK 0x1b088
+ MX6SLL_PAD_EPDC_GDSP__CSI_VSYNC 0x1b088
+ MX6SLL_PAD_EPDC_GDOE__CSI_HSYNC 0x1b088
+ MX6SLL_PAD_EPDC_DATA02__CSI_DATA02 0x1b088
+ MX6SLL_PAD_EPDC_DATA03__CSI_DATA03 0x1b088
+ MX6SLL_PAD_EPDC_DATA04__CSI_DATA04 0x1b088
+ MX6SLL_PAD_EPDC_DATA05__CSI_DATA05 0x1b088
+ MX6SLL_PAD_EPDC_DATA06__CSI_DATA06 0x1b088
+ MX6SLL_PAD_EPDC_DATA07__CSI_DATA07 0x1b088
+ MX6SLL_PAD_EPDC_SDCLK__CSI_DATA08 0x1b088
+ MX6SLL_PAD_EPDC_SDLE__CSI_DATA09 0x1b088
+ MX6SLL_PAD_EPDC_SDSHR__GPIO1_IO26 0x80000000
+ MX6SLL_PAD_EPDC_SDOE__GPIO1_IO25 0x80000000
+ >;
+ };
+
+ pinctrl_lcdif_dat: lcdifdatgrp {
+ fsl,pins = <
+ MX6SLL_PAD_LCD_DATA00__LCD_DATA00 0x79
+ MX6SLL_PAD_LCD_DATA01__LCD_DATA01 0x79
+ MX6SLL_PAD_LCD_DATA02__LCD_DATA02 0x79
+ MX6SLL_PAD_LCD_DATA03__LCD_DATA03 0x79
+ MX6SLL_PAD_LCD_DATA04__LCD_DATA04 0x79
+ MX6SLL_PAD_LCD_DATA05__LCD_DATA05 0x79
+ MX6SLL_PAD_LCD_DATA06__LCD_DATA06 0x79
+ MX6SLL_PAD_LCD_DATA07__LCD_DATA07 0x79
+ MX6SLL_PAD_LCD_DATA08__LCD_DATA08 0x79
+ MX6SLL_PAD_LCD_DATA09__LCD_DATA09 0x79
+ MX6SLL_PAD_LCD_DATA10__LCD_DATA10 0x79
+ MX6SLL_PAD_LCD_DATA11__LCD_DATA11 0x79
+ MX6SLL_PAD_LCD_DATA12__LCD_DATA12 0x79
+ MX6SLL_PAD_LCD_DATA13__LCD_DATA13 0x79
+ MX6SLL_PAD_LCD_DATA14__LCD_DATA14 0x79
+ MX6SLL_PAD_LCD_DATA15__LCD_DATA15 0x79
+ MX6SLL_PAD_LCD_DATA16__LCD_DATA16 0x79
+ MX6SLL_PAD_LCD_DATA17__LCD_DATA17 0x79
+ MX6SLL_PAD_LCD_DATA18__LCD_DATA18 0x79
+ MX6SLL_PAD_LCD_DATA19__LCD_DATA19 0x79
+ MX6SLL_PAD_LCD_DATA20__LCD_DATA20 0x79
+ MX6SLL_PAD_LCD_DATA21__LCD_DATA21 0x79
+ MX6SLL_PAD_LCD_DATA22__LCD_DATA22 0x79
+ MX6SLL_PAD_LCD_DATA23__LCD_DATA23 0x79
+ >;
+ };
+
+ pinctrl_lcdif_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6SLL_PAD_LCD_CLK__LCD_CLK 0x79
+ MX6SLL_PAD_LCD_ENABLE__LCD_ENABLE 0x79
+ MX6SLL_PAD_LCD_HSYNC__LCD_HSYNC 0x79
+ MX6SLL_PAD_LCD_VSYNC__LCD_VSYNC 0x79
+ MX6SLL_PAD_LCD_RESET__LCD_RESET 0x79
+ MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08 0x79
+ >;
+ };
+
+ pinctrl_max17135: max17135grp-1 {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_PWR_STAT__GPIO2_IO13 0x80000000 /* pwrgood */
+ MX6SLL_PAD_EPDC_VCOM0__GPIO2_IO03 0x80000000 /* vcom_ctrl */
+ MX6SLL_PAD_EPDC_PWR_WAKE__GPIO2_IO14 0x80000000 /* wakeup */
+ MX6SLL_PAD_EPDC_PWR_CTRL0__GPIO2_IO07 0x80000000 /* v3p3 */
+ MX6SLL_PAD_EPDC_PWR_IRQ__GPIO2_IO12 0x80000000 /* pwr int */
+ >;
+ };
+
+ pinctrl_spdif: spdifgrp {
+ fsl,pins = <
+ MX6SLL_PAD_SD2_DATA4__SPDIF_OUT 0x4130b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6SLL_PAD_UART1_TXD__UART1_DCE_TX 0x1b0b1
+ MX6SLL_PAD_UART1_RXD__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6SLL_PAD_SD1_CLK__SD1_CLK 0x13059
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x17059
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x17059
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x17059
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc1_100mhz: usdhc1grp_100mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170b9
+ MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130b9
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170b9
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170b9
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170b9
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc1_200mhz: usdhc1grp_200mhz {
+ fsl,pins = <
+ MX6SLL_PAD_SD1_CMD__SD1_CMD 0x170f9
+ MX6SLL_PAD_SD1_CLK__SD1_CLK 0x130f9
+ MX6SLL_PAD_SD1_DATA0__SD1_DATA0 0x170f9
+ MX6SLL_PAD_SD1_DATA1__SD1_DATA1 0x170f9
+ MX6SLL_PAD_SD1_DATA2__SD1_DATA2 0x170f9
+ MX6SLL_PAD_SD1_DATA3__SD1_DATA3 0x170f9
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1grp {
+ fsl,pins = <
+ MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID 0x17059
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6SLL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1
+ MX6SLL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pmw1grp {
+ fsl,pins = <
+ MX6SLL_PAD_PWM1__PWM1_OUT 0x110b0
+ >;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat
+ &pinctrl_lcdif_ctrl>;
+ lcd-supply = <®_lcd>;
+ display = <&display>;
+ status = "okay";
+
+ display: display {
+ bits-per-pixel = <16>;
+ bus-width = <24>;
+
+ display-timings {
+ native-mode = <&timing0>;
+ timing0: timing0 {
+ clock-frequency = <33500000>;
+ hactive = <800>;
+ vactive = <480>;
+ hback-porch = <89>;
+ hfront-porch = <164>;
+ vback-porch = <23>;
+ vfront-porch = <10>;
+ hsync-len = <10>;
+ vsync-len = <10>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ de-active = <1>;
+ pixelclk-active = <0>;
+ };
+ };
+ };
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
+ cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+ keep-power-in-suspend;
+ enable-sdio-wakeup;
+ vmmc-supply = <®_sd1_vmmc>;
+ status = "okay";
+};
+
+&usbotg1 {
+ vbus-supply = <®_usb_otg1_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ disable-over-current;
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ status = "okay";
+};
+
+&usbotg2 {
+ vbus-supply = <®_usb_otg2_vbus>;
+ dr_mode = "host";
+ disable-over-current;
+ status = "okay";
+};
--
1.9.1
More information about the linux-arm-kernel
mailing list