[PATCH v6 0/5] Altera Cyclone Passive Serial SPI FPGA Manager

[Joshua Clayton]

This series adds an FPGA manager for Altera cyclone FPGAs
that can program them using an spi port and a couple of gpios, using
Alteras passive serial protocol.

Need ACKs from ARCH maintainers for ARCH specific implementations of
__arch_bitrev8x4(), and I've added more ARCHes, so will need more ACKS, 
but the generic code will work without that patch, so if there is a holdup
the rest of the series can go in without patch 2

Changes from v5:
- Rebased on next-20161214xi
- Corrected for FPGA Mgr API change in  write_init() and write_complete()
- Better describe the device cyclone-ps-spi runs on in the file header.
- Split the bitrev8x4 patch into generic and arch specific patches...
- Added AARCH64 and MIPS implementations of bitrev8x4()... they all have to 
  have an implementation for it to compile cleanly across platforms
- Added the changes to imx6q-evi.dts to the patch set.

Changes from v4:
- Added the needed return statement to __arch_bitrev8x4()
- Added Rob Herrings ACK for and fix a typo in the commit log of patch 2

Changes from v3:
- Fixed up the state() function to return the state of the status pin
  reqested by Alan Tull
- Switched the pin to ACTIVE_LOW and coresponding logic level, and updated
  the corresponding documentation. Thanks Rob Herring for pointing out my
  mistake.
- Per Rob Herring, switched from "gpio" to "gpios" in dts

Changes from v2:
- Merged patch 3 and 4 as suggested in review by Moritz Fischer
- Changed FPGA_MIN_DELAY from 250 to 50 ms is the time advertized by
  Altera. This now works, as we don't assume it is done

Changes from v1:
- Changed the name from cyclone-spi-fpga-mgr to cyclone-ps-spi-fpga-mgr
  This name change was requested by Alan Tull, to be specific about which
  programming method is being employed on the fpga.
- Changed the name of the reset-gpio to config-gpio to closer match the
  way the pins are described in the Altera manual
- Moved MODULE_LICENCE, _AUTHOR, and _DESCRIPTION to the bottom

- Added a bitrev8x4() function to the bitrev headers and implemented ARM
 const, runtime, and ARM specific faster versions (This may end up
 needing to be a standalone patch)

- Moved the bitswapping into cyclonespi_write(), as requested.
  This falls short of my desired generic lsb first spi support, but is a step
  in that direction.

- Fixed whitespace problems introduced during refactoring

- Replaced magic number for initial delay with a descriptive macro
- Poll the fpga to see when it is ready rather than a fixed 1 ms sleep

Joshua Clayton (5):
  lib: add bitrev8x4()
  lib: implement __arch_bitrev8x4()
  doc: dt: add cyclone-ps-spi binding document
  fpga manager: Add cyclone-ps-spi driver for Altera FPGAs
  ARM: dts: imx6q-evi: support cyclone-ps-spi

 .../bindings/fpga/cyclone-ps-spi-fpga-mgr.txt      |  25 +++
 arch/arm/boot/dts/imx6q-evi.dts                    |  16 ++
 arch/arm/include/asm/bitrev.h                      |   6 +
 arch/arm64/include/asm/bitrev.h                    |   6 +
 arch/mips/include/asm/bitrev.h                     |   6 +
 drivers/fpga/Kconfig                               |   7 +
 drivers/fpga/Makefile                              |   1 +
 drivers/fpga/cyclone-ps-spi.c                      | 186 +++++++++++++++++++++
 include/linux/bitrev.h                             |  26 +++
 9 files changed, 279 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/fpga/cyclone-ps-spi-fpga-mgr.txt
 create mode 100644 drivers/fpga/cyclone-ps-spi.c

-- 
2.9.3