[PATCH v6 4/5] [media] dt-bindings: add TI VPIF documentation
Kevin Hilman
khilman at baylibre.com
Wed Dec 7 10:30:24 PST 2016
Acked-by: Rob Herring <robh at kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart at ideasonboard.com>
Signed-off-by: Kevin Hilman <khilman at baylibre.com>
---
.../devicetree/bindings/media/ti,da850-vpif.txt | 83 ++++++++++++++++++++++
1 file changed, 83 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/ti,da850-vpif.txt
diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
new file mode 100644
index 000000000000..6d25d7f23d26
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
@@ -0,0 +1,83 @@
+Texas Instruments VPIF
+----------------------
+
+The TI Video Port InterFace (VPIF) is the primary component for video
+capture and display on the DA850/AM18x family of TI DaVinci/Sitara
+SoCs.
+
+TI Document reference: SPRUH82C, Chapter 35
+http://www.ti.com/lit/pdf/spruh82
+
+Required properties:
+- compatible: must be "ti,da850-vpif"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the VPIF
+
+Video Capture:
+
+VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a
+single 16-bit channel. It should contain at least one port child node
+with child 'endpoint' node. Please refer to the bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example using 2 8-bit input channels, one of which is connected to an
+I2C-connected TVP5147 decoder:
+
+ vpif: vpif at 217000 {
+ compatible = "ti,da850-vpif";
+ reg = <0x217000 0x1000>;
+ interrupts = <92>;
+
+ port {
+ vpif_ch0: endpoint at 0 {
+ reg = <0>;
+ bus-width = <8>;
+ remote-endpoint = <&composite>;
+ };
+
+ vpif_ch1: endpoint at 1 {
+ reg = <1>;
+ bus-width = <8>;
+ data-shift = <8>;
+ };
+ };
+ };
+
+[ ... ]
+
+&i2c0 {
+
+ tvp5147 at 5d {
+ compatible = "ti,tvp5147";
+ reg = <0x5d>;
+ status = "okay";
+
+ port {
+ composite: endpoint {
+ hsync-active = <1>;
+ vsync-active = <1>;
+ pclk-sample = <0>;
+
+ /* VPIF channel 0 (lower 8-bits) */
+ remote-endpoint = <&vpif_ch0>;
+ bus-width = <8>;
+ };
+ };
+ };
+};
+
+
+Alternatively, an example when the bus is configured as a single
+16-bit input (e.g. for raw-capture mode):
+
+ vpif: vpif at 217000 {
+ compatible = "ti,da850-vpif";
+ reg = <0x217000 0x1000>;
+ interrupts = <92>;
+
+ port {
+ vpif_ch0: endpoint {
+ bus-width = <16>;
+ };
+ };
+ };
--
2.9.3
More information about the linux-arm-kernel
mailing list