[PATCHv4 11/15] clk: ti: clockdomain: add clock provider support to clockdomains
Tony Lindgren
tony at atomide.com
Fri Dec 2 15:12:40 PST 2016
* Michael Turquette <mturquette at baylibre.com> [161202 14:34]:
> Quoting Tony Lindgren (2016-10-28 16:54:48)
> > * Stephen Boyd <sboyd at codeaurora.org> [161028 16:37]:
> > > On 10/28, Tony Lindgren wrote:
> > > > * Tero Kristo <t-kristo at ti.com> [161028 00:43]:
> > > > > On 28/10/16 03:50, Stephen Boyd wrote:
> > > > > > I suppose a PRCM is
> > > > > > like an MFD that has clocks and resets under it? On other
> > > > > > platforms we've combined that all into one node and just had
> > > > > > #clock-cells and #reset-cells in that node. Is there any reason
> > > > > > we can't do that here?
> > > > >
> > > > > For OMAPs, there are typically multiple instances of the PRCM around; OMAP4
> > > > > for example has:
> > > > >
> > > > > cm1 @ 0x4a004000 (clocks + clockdomains)
> > > > > cm2 @ 0x4a008000 (clocks + clockdomains)
> > > > > prm @ 0x4a306000 (few clocks + resets + power state handling)
> > > > > scrm @ 0x4a30a000 (few external clocks + plenty of misc stuff)
> > > > >
> > > > > These instances are also under different power/voltage domains which means
> > > > > their PM behavior is different.
> > > > >
> > > > > The idea behind having a clockdomain as a provider was mostly to have the
> > > > > topology visible : prcm-instance -> clockdomain -> clocks
> > > >
> > > > Yeah that's needed to get the interconnect hierarchy right for
> > > > genpd :)
> > > >
> > > > > ... but basically I think it would be possible to drop the clockdomain
> > > > > representation and just mark the prcm-instance as a clock provider. Tony,
> > > > > any thoughts on that?
> > > >
> > > > No let's not drop the clockdomains as those will be needed when we
> > > > move things into proper hierarchy within the interconnect instances.
> > > > This will then help with getting things right with genpd.
> > > >
> > > > In the long run we just want to specify clockdomain and the offset of
> > > > the clock instance within the clockdomain in the dts files.
> > > >
> > >
> > > Sorry, I have very little idea how OMAP hardware works. Do you
> > > mean that you will have different nodes for each clockdomain so
> > > that genpd can map 1:1 to the node in dts? But in hardware
> > > there's a prcm that allows us to control many clock domains
> > > through register read/writes? How is the interconnect involved?
> >
> > There are multiple clockdomains, at least one for each interconnect
> > instance. Once a clockdomain is idle, the related interconnect can
> > idle too. So yeah genpd pretty much maps 1:1 with the clockdomains.
> >
> > There's more info in for example omap4 TRM section "3.4.1 Device
> > Power-Management Layout" that shows the voltage/power/clock domains.
> > The interconnect instances are mostly named there too looking at
> > the L4/L3 naming.
>
> I'm confused on two points:
>
> 1) why are the clkdm's acting as clock providers? I've always hated the
> name "clock domain" since those bits are for managing module state, not
> clock state. The PRM, CM1 and CM2 provide the clocks, not the
> clockdomains.
The clock domains have multiple clock inputs that are routed to multiple
child clocks. So it is a clock :)
See for example omap4430 TRM "3.6.4 CD_WKUP Clock Domain" on page
393 in my revision here.
On that page "Figure 3-48" shows CD_WKUP with the four input clocks.
And then "Table 3-84. CD_WKUP Control and Status Parameters" shows
the CD_WKUP clock domain specific registers. These registers show
the status, I think they are all read-only registers. Then CD_WKUP
has multiple child clocks with configurable registers.
>From hardware register point of view, each clock domain has:
- Read-only clockdomain status registers in the beginning of
the address space
- Multiple similar clock instances register instances each
mapping to a specific interconnect target module
These are documented in "3.11.16.1 WKUP_CM Register Summary".
>From hardware point of view, we ideally want to map interconnect
target modules to the clock instance offset from the clock domain
for that interconnect segment. For example gptimer1 clocks would
be just:
clocks = <&cd_wkup 0x40>;
> 2) why aren't the clock domains modeled as genpds with their associated
> devices attached to them? Note that it is possible to "nest" genpd
> objects. This would also allow for the "Clockdomain Dependency"
> relationships to be properly modeled (see section 3.1.1.1.7 Clock Domain
> Dependency in the OMAP4 TRM).
Clock domains only route clocks to child clocks. Power domains
are different registers. The power domains map roughly to
interconnect instances, there we have registers to disable the
whole interconnect when idle.
Regards,
Tony
More information about the linux-arm-kernel
mailing list