XHCI controller does not detect USB key insertion
Felipe Balbi
felipe.balbi at linux.intel.com
Fri Dec 2 01:03:14 PST 2016
Hi,
Mason <slash.tmp at free.fr> writes:
> Hello everyone,
>
> I'm trying out a SoC with a brand new USB controller, which is (supposedly)
> a standard XHCI controller. In theory, I would just need to build the right
> driver, and everything would auto-magically work, right?
perhaps, but there might be needed initialization of other resources
like PHYs and stuff like that.
> So my defconfig contains:
>
> CONFIG_USB=y
> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
> CONFIG_USB_XHCI_HCD=y
> CONFIG_USB_XHCI_PLATFORM=y
> CONFIG_USB_STORAGE=y
> CONFIG_USB_STORAGE_DEBUG=y
>
>
> And my device tree contains:
>
> usb3 at 30040000 {
> compatible = "generic-xhci";
> reg = <0x30040000 0x10000>;
> interrupts = <SIGMA_HWIRQ 67 IRQ_TYPE_LEVEL_HIGH>;
> };
>
>
> The boot messages I get:
>
> [ 1.618214] xhci-hcd 30040000.usb3: xHCI Host Controller
> [ 1.623611] xhci-hcd 30040000.usb3: new USB bus registered, assigned bus number 1
> [ 1.631181] reset function is xhci_plat_setup
> [ 1.635588] xhci_plat_setup from usb_add_hcd
> [ 1.640109] xhci-hcd 30040000.usb3: hcc params 0x30003192 hci version 0x100 quirks 0x00010010
> [ 1.648766] xhci-hcd 30040000.usb3: irq 22, io mem 0x30040000
> [ 1.654572] xhci_plat_start from usb_add_hcd
> [ 1.659086] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 1.665943] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 1.673228] usb usb1: Product: xHCI Host Controller
> [ 1.678154] usb usb1: Manufacturer: Linux 4.7.0-rc6 xhci-hcd
> [ 1.683865] usb usb1: SerialNumber: 30040000.usb3
> [ 1.689391] hub 1-0:1.0: USB hub found
> [ 1.693227] hub 1-0:1.0: 1 port detected
> [ 1.697601] xhci-hcd 30040000.usb3: xHCI Host Controller
> [ 1.702983] xhci-hcd 30040000.usb3: new USB bus registered, assigned bus number 2
> [ 1.710545] reset function is xhci_plat_setup
> [ 1.714950] xhci_plat_setup from usb_add_hcd
> [ 1.719265] xhci_plat_start from usb_add_hcd
> [ 1.723653] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
> [ 1.731956] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
> [ 1.738814] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 1.746100] usb usb2: Product: xHCI Host Controller
> [ 1.751025] usb usb2: Manufacturer: Linux 4.7.0-rc6 xhci-hcd
> [ 1.756736] usb usb2: SerialNumber: 30040000.usb3
> [ 1.762195] hub 2-0:1.0: USB hub found
> [ 1.766027] hub 2-0:1.0: 1 port detected
> [ 1.770661] usbcore: registered new interface driver usb-storage
> [ 1.784584] usbcore: registered new interface driver usbhid
> [ 1.790213] usbhid: USB HID core driver
>
> Which looks encouraging, right?
yes
> Am I supposed to have had USB interrupts at that point?
nope, unless a device was already plugged in.
> # cat /proc/interrupts
> CPU0 CPU1 CPU2 CPU3
> 20: 609 365 393 356 GIC-0 29 Edge twd
> 21: 101 0 0 0 INTC 1 Level serial
> 22: 0 0 0 0 INTC 67 Level xhci-hcd:usb1
> IPI0: 0 0 0 0 CPU wakeup interrupts
> IPI1: 0 0 0 0 Timer broadcast interrupts
> IPI2: 794 620 1223 1045 Rescheduling interrupts
> IPI3: 0 37 37 37 Function call interrupts
> IPI4: 0 0 0 0 CPU stop interrupts
> IPI5: 0 0 0 0 IRQ work interrupts
> IPI6: 0 0 0 0 completion interrupts
> Err: 0
>
>
> When I insert a USB key, nothing happens :-(
>
> # lsusb -v
> Bus 001 Device 001: ID 1d6b:0002
> Bus 002 Device 001: ID 1d6b:0003
>
>
> I'd like to hear suggestions about what I can tweak to fix the problem.
go to your documentation and see if you have initialized
everything. Which SoC is this?
--
balbi
More information about the linux-arm-kernel
mailing list