[PATCH v2 7/8] ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators

[Chen-Yu Tsai]

The AXP806 PMIC is the secondary PMIC. It provides various supply
voltages for the SoC and other peripherals. The PMIC's interrupt
line is connected to NMI pin of the SoC.

Signed-off-by: Chen-Yu Tsai <wens at csie.org>
---
Changes since v1:

  - Fixed up bldo* voltage constraints to match regulator voltage step.

---
 arch/arm/boot/dts/sun9i-a80-cubieboard4.dts | 112 ++++++++++++++++++++++++++++
 1 file changed, 112 insertions(+)

diff --git a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
index 910b29f0f0b5..439847acd41e 100644
--- a/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
+++ b/arch/arm/boot/dts/sun9i-a80-cubieboard4.dts
@@ -260,6 +260,118 @@
 		};
 	};
 
+	axp806: pmic at 745 {
+		compatible = "x-powers,axp806";
+		reg = <0x745>;
+		interrupt-parent = <&nmi_intc>;
+		interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		bldoin-supply = <&reg_dcdce>;
+
+		regulators {
+			reg_s_aldo1: aldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "avcc";
+			};
+
+			aldo2 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo2";
+			};
+
+			aldo3 {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's aldo's
+				 */
+				regulator-name = "s_aldo3";
+			};
+
+			reg_bldo1: bldo1 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name = "vcc18-efuse-adc-display-csi";
+			};
+
+			reg_bldo2: bldo2 {
+				regulator-always-on;
+				regulator-min-microvolt = <1700000>;
+				regulator-max-microvolt = <1900000>;
+				regulator-name =
+					"vdd18-drampll-vcc18-pll-cpvdd";
+			};
+
+			bldo3 {
+				/* unused */
+			};
+
+			reg_bldo4: bldo4 {
+				regulator-min-microvolt = <1100000>;
+				regulator-max-microvolt = <1300000>;
+				regulator-name = "vcc12-hsic";
+			};
+
+			reg_cldo1: cldo1 {
+				/*
+				 * This was 3V in the original design, but
+				 * 3.3V is the recommended supply voltage
+				 * for the Ethernet PHY.
+				 */
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc-gmac-phy";
+			};
+
+			reg_cldo2: cldo2 {
+				regulator-min-microvolt = <2800000>;
+				regulator-max-microvolt = <2800000>;
+				regulator-name = "afvcc-cam";
+			};
+
+			reg_cldo3: cldo3 {
+				regulator-min-microvolt = <3000000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-name = "vcc-io-wifi-codec-io2";
+			};
+
+			reg_dcdca: dcdca {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-cpub";
+			};
+
+			reg_dcdcd: dcdcd {
+				regulator-always-on;
+				regulator-min-microvolt = <800000>;
+				regulator-max-microvolt = <1100000>;
+				regulator-name = "vdd-vpu";
+			};
+
+			reg_dcdce: dcdce {
+				regulator-always-on;
+				regulator-min-microvolt = <2100000>;
+				regulator-max-microvolt = <2100000>;
+				regulator-name = "vcc-bldo-codec-ldoin";
+			};
+
+			sw {
+				/*
+				 * unused, but use a different name to
+				 * avoid name clash with axp809's sw
+				 */
+				regulator-name = "s_sw";
+			};
+		};
+	};
+
 	ac100: codec at e89 {
 		compatible = "x-powers,ac100";
 		reg = <0xe89>;
-- 
2.9.3