[v13.1 PATCH 2/5] phy: Add USB Type-C PHY driver for rk3399
Chris Zhong
zyw at rock-chips.com
Tue Aug 23 22:00:38 PDT 2016
Hi Chanwoo
On 08/23/2016 01:44 PM, Chanwoo Choi wrote:
> Hi Chris,
>
> The name of 'SuperSpeed' property is changed
> from EXTCON_PROP_USB_SUPERSPEED to EXTCON_PROP_USB_SS.
>
> The name change was discussed on mail thread[1].
Oh, since I was using the old name in my local kernel, I will change it
in V14.
Thanks.
>
> Also, this driver depend on the extcon git repository.
> So, I created the immutable branch(ib-extcon-phy-4.9)[2] for phy framework
> to prevent the build error before merging the Linus git repository.
>
> [1] https://lkml.org/lkml/2016/8/17/622
> [2] git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon.git ib-extcon-phy-4.9
>
> Regards,
> Chanwoo Choi
>
> On 2016년 08월 23일 14:02, Chris Zhong wrote:
>> Add a PHY provider driver for the rk3399 SoC Type-c PHY. The USB
>> Type-C PHY is designed to support the USB3 and DP applications.
>> The USB3 operates in SuperSpeed mode and the DP can operate at RBR,
>> HBR and HBR2 data rates. This driver create 2 PHY devices separately
>> for USB3 and DisplyPort, and registers them under the child node.
>>
>> Signed-off-by: Chris Zhong <zyw at rock-chips.com>
>> Signed-off-by: Kever Yang <kever.yang at rock-chips.com>
>> Reviewed-by: Guenter Roeck <groeck at chromium.org>
>> Tested-by: Guenter Roeck <groeck at chromium.org>
>>
>> ---
>>
>> Changes in v13.1:
>> - add some description in front of driver
>> - change name of usb to usb3
>> - add a USB3 RX register configuration
>>
>> Changes in v13:
>> - do not return err if nothing connected with Type-C, when usb phy power on,
>> since the USB core driver will call phy power without USB3 device connected.
>>
>> Changes in v12:
>> - enable DP+USB3 mode, only when EXTCON_PROP_USB_SUPERSPEED equal 1
>> and DP is attached
>>
>> Changes in v11:
>> - make a clearer demarcation between usb phy and dp phy.
>>
>> Changes in v10:
>> - do not control dp select and hpd config in phy driver
>>
>> Changes in v9:
>> - the new_mode should be int not u8
>> - move mutex_lock(&tcphy->lock); to earlier place. in
>> rockchip_usb3_phy_power_off
>> - better mutex lock for phy mode and flip
>> - split the Type-C PHY into two PHYs: USB3 and DP
>>
>> Changes in v8:
>> - set the default cable id to EXTCON_USB_HOST
>> - optimization Error log
>>
>> Changes in v7:
>> - support new API of extcon
>>
>> Changes in v6:
>> - delete the support of PIN_ASSIGN_A/B
>> - set the default mode to MODE_DFP_USB
>> - disable DP PLL at USB3 only mode
>>
>> Changes in v5:
>> - support get property from extcon
>> - remove PIN ASSIGN A/B support
>>
>> Changes in v4:
>> - select EXTCON
>> - use phy framework to control the USB3 and DP function
>> - rename PIN_MAP_ to PIN_ASSIGN_
>>
>> Changes in v3:
>> - remove the phy framework(Kishon Vijay Abraham I)
>> - add parentheses around the macro
>> - use a single space between type and name
>> - add spaces after opening and before closing braces.
>> - use u16 for register value
>> - remove type-c phy header file
>> - CodingStyle optimization
>> - use some cable extcon to get type-c port information
>> - add a extcon to notify Display Port
>>
>> Changes in v2:
>> - select RESET_CONTROLLER
>> - alphabetic order
>> - modify some spelling mistakes
>> - make mode cleaner
>> - use bool for enable/disable
>> - check all of the return value
>> - return a better err number
>> - use more readx_poll_timeout()
>> - clk_disable_unprepare(tcphy->clk_ref);
>> - remove unuse functions, rockchip_typec_phy_power_on/off
>> - remove unnecessary typecast from void *
>> - use dts node to distinguish between phys.
>>
>> Changes in v1:
>> - update the licence note
>> - init core clock to 50MHz
>> - use extcon API
>> - remove unused global
>> - add some comments for magic num
>> - change usleep_range(1000, 2000) tousleep_range(1000, 1050)
>> - remove __func__ from dev_err
>> - return err number when get clk failed
>> - remove ADDR_ADJ define
>> - use devm_clk_get(&pdev->dev, "tcpdcore")
>>
>> drivers/phy/Kconfig | 9 +
>> drivers/phy/Makefile | 1 +
>> drivers/phy/phy-rockchip-typec.c | 1013 ++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 1023 insertions(+)
>> create mode 100644 drivers/phy/phy-rockchip-typec.c
>>
>> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
>> index 42f3e30..c775fd7 100644
>> --- a/drivers/phy/Kconfig
>> +++ b/drivers/phy/Kconfig
>> @@ -348,6 +348,15 @@ config PHY_ROCKCHIP_PCIE
>> help
>> Enable this to support the Rockchip PCIe PHY.
>>
>> +config PHY_ROCKCHIP_TYPEC
>> + tristate "Rockchip TYPEC PHY Driver"
>> + depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
>> + select EXTCON
>> + select GENERIC_PHY
>> + select RESET_CONTROLLER
>> + help
>> + Enable this to support the Rockchip USB TYPEC PHY.
>> +
>> config PHY_ST_SPEAR1310_MIPHY
>> tristate "ST SPEAR1310-MIPHY driver"
>> select GENERIC_PHY
>> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
>> index fbb91e7..5d58b63 100644
>> --- a/drivers/phy/Makefile
>> +++ b/drivers/phy/Makefile
>> @@ -39,6 +39,7 @@ obj-$(CONFIG_PHY_ROCKCHIP_INNO_USB2) += phy-rockchip-inno-usb2.o
>> obj-$(CONFIG_PHY_ROCKCHIP_EMMC) += phy-rockchip-emmc.o
>> obj-$(CONFIG_PHY_ROCKCHIP_PCIE) += phy-rockchip-pcie.o
>> obj-$(CONFIG_PHY_ROCKCHIP_DP) += phy-rockchip-dp.o
>> +obj-$(CONFIG_PHY_ROCKCHIP_TYPEC) += phy-rockchip-typec.o
>> obj-$(CONFIG_PHY_QCOM_IPQ806X_SATA) += phy-qcom-ipq806x-sata.o
>> obj-$(CONFIG_PHY_ST_SPEAR1310_MIPHY) += phy-spear1310-miphy.o
>> obj-$(CONFIG_PHY_ST_SPEAR1340_MIPHY) += phy-spear1340-miphy.o
>> diff --git a/drivers/phy/phy-rockchip-typec.c b/drivers/phy/phy-rockchip-typec.c
>> new file mode 100644
>> index 0000000..fff1b27
>> --- /dev/null
>> +++ b/drivers/phy/phy-rockchip-typec.c
>> @@ -0,0 +1,1013 @@
>> +/*
>> + * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
>> + * Author: Chris Zhong <zyw at rock-chips.com>
>> + * Kever Yang <kever.yang at rock-chips.com>
>> + *
>> + * This software is licensed under the terms of the GNU General Public
>> + * License version 2, as published by the Free Software Foundation, and
>> + * may be copied, distributed, and modified under those terms.
>> + *
>> + * This program is distributed in the hope that it will be useful,
>> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
>> + * GNU General Public License for more details.
>> + *
>> + * The ROCKCHIP Type-C PHY has two PLL clocks. The first PLL clock
>> + * is used for USB3, the second PLL clock is used for DP. This Type-C PHY has
>> + * 3 working modes: USB3 only mode, DP only mode, and USB3+DP mode.
>> + * At USB3 only mode, both PLL clocks need to be initialized, this allows the
>> + * PHY to switch mode between USB3 and USB3+DP, without disconnecting the USB
>> + * device.
>> + * In The DP only mode, only the DP PLL needs to be powered on, and the 4 lanes
>> + * are all used for DP.
>> + *
>> + * This driver gets extcon cable state and property, then decides which mode to
>> + * select:
>> + *
>> + * 1. USB3 only mode:
>> + * EXTCON_USB or EXTCON_USB_HOST state is true, and
>> + * EXTCON_PROP_USB_SUPERSPEED property is true.
>> + * EXTCON_DISP_DP state is false.
>> + *
>> + * 2. DP only mode:
>> + * EXTCON_DISP_DP state is true, and
>> + * EXTCON_PROP_USB_SUPERSPEED property is false.
>> + * If EXTCON_USB_HOST state is true, it is DP + USB2 mode, since the USB2 phy
>> + * is a separate phy, so this case is still DP only mode.
>> + *
>> + * 3. USB3+DP mode:
>> + * EXTCON_USB_HOST and EXTCON_DISP_DP are both true, and
>> + * EXTCON_PROP_USB_SUPERSPEED property is true.
>> + *
>> + * This Type-C PHY driver supports normal and flip orientation. The orientation
>> + * is reported by the EXTCON_PROP_USB_TYPEC_POLARITY property: true is flip
>> + * orientation, false is normal orientation.
>> + *
>> + */
>> +
>> +#include <linux/clk.h>
>> +#include <linux/clk-provider.h>
>> +#include <linux/delay.h>
>> +#include <linux/extcon.h>
>> +#include <linux/io.h>
>> +#include <linux/iopoll.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/mutex.h>
>> +#include <linux/of.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +#include <linux/reset.h>
>> +
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/phy/phy.h>
>> +
>> +#define CMN_SSM_BANDGAP (0x21 << 2)
>> +#define CMN_SSM_BIAS (0x22 << 2)
>> +#define CMN_PLLSM0_PLLEN (0x29 << 2)
>> +#define CMN_PLLSM0_PLLPRE (0x2a << 2)
>> +#define CMN_PLLSM0_PLLVREF (0x2b << 2)
>> +#define CMN_PLLSM0_PLLLOCK (0x2c << 2)
>> +#define CMN_PLLSM1_PLLEN (0x31 << 2)
>> +#define CMN_PLLSM1_PLLPRE (0x32 << 2)
>> +#define CMN_PLLSM1_PLLVREF (0x33 << 2)
>> +#define CMN_PLLSM1_PLLLOCK (0x34 << 2)
>> +#define CMN_PLLSM1_USER_DEF_CTRL (0x37 << 2)
>> +#define CMN_ICAL_OVRD (0xc1 << 2)
>> +#define CMN_PLL0_VCOCAL_OVRD (0x83 << 2)
>> +#define CMN_PLL0_VCOCAL_INIT (0x84 << 2)
>> +#define CMN_PLL0_VCOCAL_ITER (0x85 << 2)
>> +#define CMN_PLL0_LOCK_REFCNT_START (0x90 << 2)
>> +#define CMN_PLL0_LOCK_PLLCNT_START (0x92 << 2)
>> +#define CMN_PLL0_LOCK_PLLCNT_THR (0x93 << 2)
>> +#define CMN_PLL0_INTDIV (0x94 << 2)
>> +#define CMN_PLL0_FRACDIV (0x95 << 2)
>> +#define CMN_PLL0_HIGH_THR (0x96 << 2)
>> +#define CMN_PLL0_DSM_DIAG (0x97 << 2)
>> +#define CMN_PLL0_SS_CTRL1 (0x98 << 2)
>> +#define CMN_PLL0_SS_CTRL2 (0x99 << 2)
>> +#define CMN_PLL1_VCOCAL_START (0xa1 << 2)
>> +#define CMN_PLL1_VCOCAL_OVRD (0xa3 << 2)
>> +#define CMN_PLL1_VCOCAL_INIT (0xa4 << 2)
>> +#define CMN_PLL1_VCOCAL_ITER (0xa5 << 2)
>> +#define CMN_PLL1_LOCK_REFCNT_START (0xb0 << 2)
>> +#define CMN_PLL1_LOCK_PLLCNT_START (0xb2 << 2)
>> +#define CMN_PLL1_LOCK_PLLCNT_THR (0xb3 << 2)
>> +#define CMN_PLL1_INTDIV (0xb4 << 2)
>> +#define CMN_PLL1_FRACDIV (0xb5 << 2)
>> +#define CMN_PLL1_HIGH_THR (0xb6 << 2)
>> +#define CMN_PLL1_DSM_DIAG (0xb7 << 2)
>> +#define CMN_PLL1_SS_CTRL1 (0xb8 << 2)
>> +#define CMN_PLL1_SS_CTRL2 (0xb9 << 2)
>> +#define CMN_RXCAL_OVRD (0xd1 << 2)
>> +#define CMN_TXPUCAL_CTRL (0xe0 << 2)
>> +#define CMN_TXPUCAL_OVRD (0xe1 << 2)
>> +#define CMN_TXPDCAL_OVRD (0xf1 << 2)
>> +#define CMN_DIAG_PLL0_FBH_OVRD (0x1c0 << 2)
>> +#define CMN_DIAG_PLL0_FBL_OVRD (0x1c1 << 2)
>> +#define CMN_DIAG_PLL0_OVRD (0x1c2 << 2)
>> +#define CMN_DIAG_PLL0_V2I_TUNE (0x1c5 << 2)
>> +#define CMN_DIAG_PLL0_CP_TUNE (0x1c6 << 2)
>> +#define CMN_DIAG_PLL0_LF_PROG (0x1c7 << 2)
>> +#define CMN_DIAG_PLL1_FBH_OVRD (0x1d0 << 2)
>> +#define CMN_DIAG_PLL1_FBL_OVRD (0x1d1 << 2)
>> +#define CMN_DIAG_PLL1_OVRD (0x1d2 << 2)
>> +#define CMN_DIAG_PLL1_V2I_TUNE (0x1d5 << 2)
>> +#define CMN_DIAG_PLL1_CP_TUNE (0x1d6 << 2)
>> +#define CMN_DIAG_PLL1_LF_PROG (0x1d7 << 2)
>> +#define CMN_DIAG_PLL1_PTATIS_TUNE1 (0x1d8 << 2)
>> +#define CMN_DIAG_PLL1_PTATIS_TUNE2 (0x1d9 << 2)
>> +#define CMN_DIAG_PLL1_INCLK_CTRL (0x1da << 2)
>> +#define CMN_DIAG_HSCLK_SEL (0x1e0 << 2)
>> +
>> +#define XCVR_PSM_RCTRL(n) ((0x4001 | ((n) << 9)) << 2)
>> +#define XCVR_PSM_CAL_TMR(n) ((0x4002 | ((n) << 9)) << 2)
>> +#define XCVR_PSM_A0IN_TMR(n) ((0x4003 | ((n) << 9)) << 2)
>> +#define TX_TXCC_CAL_SCLR_MULT(n) ((0x4047 | ((n) << 9)) << 2)
>> +#define TX_TXCC_CPOST_MULT_00(n) ((0x404c | ((n) << 9)) << 2)
>> +#define TX_TXCC_CPOST_MULT_01(n) ((0x404d | ((n) << 9)) << 2)
>> +#define TX_TXCC_CPOST_MULT_10(n) ((0x404e | ((n) << 9)) << 2)
>> +#define TX_TXCC_CPOST_MULT_11(n) ((0x404f | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_000(n) ((0x4050 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_001(n) ((0x4051 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_010(n) ((0x4052 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_011(n) ((0x4053 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_100(n) ((0x4054 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_101(n) ((0x4055 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_110(n) ((0x4056 | ((n) << 9)) << 2)
>> +#define TX_TXCC_MGNFS_MULT_111(n) ((0x4057 | ((n) << 9)) << 2)
>> +#define XCVR_DIAG_PLLDRC_CTRL(n) ((0x40e0 | ((n) << 9)) << 2)
>> +#define XCVR_DIAG_BIDI_CTRL(n) ((0x40e8 | ((n) << 9)) << 2)
>> +#define XCVR_DIAG_LANE_FCM_EN_MGN(n) ((0x40f2 | ((n) << 9)) << 2)
>> +#define TX_PSC_A0(n) ((0x4100 | ((n) << 9)) << 2)
>> +#define TX_PSC_A1(n) ((0x4101 | ((n) << 9)) << 2)
>> +#define TX_PSC_A2(n) ((0x4102 | ((n) << 9)) << 2)
>> +#define TX_PSC_A3(n) ((0x4103 | ((n) << 9)) << 2)
>> +#define TX_RCVDET_CTRL(n) ((0x4120 | ((n) << 9)) << 2)
>> +#define TX_RCVDET_EN_TMR(n) ((0x4122 | ((n) << 9)) << 2)
>> +#define TX_RCVDET_ST_TMR(n) ((0x4123 | ((n) << 9)) << 2)
>> +#define TX_DIAG_TX_DRV(n) ((0x41e1 | ((n) << 9)) << 2)
>> +#define TX_DIAG_BGREF_PREDRV_DELAY (0x41e7 << 2)
>> +#define TX_ANA_CTRL_REG_1 (0x5020 << 2)
>> +#define TX_ANA_CTRL_REG_2 (0x5021 << 2)
>> +#define TXDA_COEFF_CALC_CTRL (0x5022 << 2)
>> +#define TX_DIG_CTRL_REG_2 (0x5024 << 2)
>> +#define TXDA_CYA_AUXDA_CYA (0x5025 << 2)
>> +#define TX_ANA_CTRL_REG_3 (0x5026 << 2)
>> +#define TX_ANA_CTRL_REG_4 (0x5027 << 2)
>> +#define TX_ANA_CTRL_REG_5 (0x5029 << 2)
>> +
>> +#define RX_PSC_A0(n) ((0x8000 | ((n) << 9)) << 2)
>> +#define RX_PSC_A1(n) ((0x8001 | ((n) << 9)) << 2)
>> +#define RX_PSC_A2(n) ((0x8002 | ((n) << 9)) << 2)
>> +#define RX_PSC_A3(n) ((0x8003 | ((n) << 9)) << 2)
>> +#define RX_PSC_CAL(n) ((0x8006 | ((n) << 9)) << 2)
>> +#define RX_PSC_RDY(n) ((0x8007 | ((n) << 9)) << 2)
>> +#define RX_IQPI_ILL_CAL_OVRD (0x8023 << 2)
>> +#define RX_EPI_ILL_CAL_OVRD (0x8033 << 2)
>> +#define RX_SDCAL0_OVRD (0x8041 << 2)
>> +#define RX_SDCAL1_OVRD (0x8049 << 2)
>> +#define RX_SLC_INIT (0x806d << 2)
>> +#define RX_SLC_RUN (0x806e << 2)
>> +#define RX_CDRLF_CNFG2 (0x8081 << 2)
>> +#define RX_SIGDET_HL_FILT_TMR(n) ((0x8090 | ((n) << 9)) << 2)
>> +#define RX_SLC_IOP0_OVRD (0x8101 << 2)
>> +#define RX_SLC_IOP1_OVRD (0x8105 << 2)
>> +#define RX_SLC_QOP0_OVRD (0x8109 << 2)
>> +#define RX_SLC_QOP1_OVRD (0x810d << 2)
>> +#define RX_SLC_EOP0_OVRD (0x8111 << 2)
>> +#define RX_SLC_EOP1_OVRD (0x8115 << 2)
>> +#define RX_SLC_ION0_OVRD (0x8119 << 2)
>> +#define RX_SLC_ION1_OVRD (0x811d << 2)
>> +#define RX_SLC_QON0_OVRD (0x8121 << 2)
>> +#define RX_SLC_QON1_OVRD (0x8125 << 2)
>> +#define RX_SLC_EON0_OVRD (0x8129 << 2)
>> +#define RX_SLC_EON1_OVRD (0x812d << 2)
>> +#define RX_SLC_IEP0_OVRD (0x8131 << 2)
>> +#define RX_SLC_IEP1_OVRD (0x8135 << 2)
>> +#define RX_SLC_QEP0_OVRD (0x8139 << 2)
>> +#define RX_SLC_QEP1_OVRD (0x813d << 2)
>> +#define RX_SLC_EEP0_OVRD (0x8141 << 2)
>> +#define RX_SLC_EEP1_OVRD (0x8145 << 2)
>> +#define RX_SLC_IEN0_OVRD (0x8149 << 2)
>> +#define RX_SLC_IEN1_OVRD (0x814d << 2)
>> +#define RX_SLC_QEN0_OVRD (0x8151 << 2)
>> +#define RX_SLC_QEN1_OVRD (0x8155 << 2)
>> +#define RX_SLC_EEN0_OVRD (0x8159 << 2)
>> +#define RX_SLC_EEN1_OVRD (0x815d << 2)
>> +#define RX_REE_CTRL_DATA_MASK(n) ((0x81bb | ((n) << 9)) << 2)
>> +#define RX_DIAG_SIGDET_TUNE(n) ((0x81dc | ((n) << 9)) << 2)
>> +#define RX_DIAG_SC2C_DELAY (0x81e1 << 2)
>> +
>> +#define PMA_LANE_CFG (0xc000 << 2)
>> +#define PIPE_CMN_CTRL1 (0xc001 << 2)
>> +#define PIPE_CMN_CTRL2 (0xc002 << 2)
>> +#define PIPE_COM_LOCK_CFG1 (0xc003 << 2)
>> +#define PIPE_COM_LOCK_CFG2 (0xc004 << 2)
>> +#define PIPE_RCV_DET_INH (0xc005 << 2)
>> +#define DP_MODE_CTL (0xc008 << 2)
>> +#define DP_CLK_CTL (0xc009 << 2)
>> +#define STS (0xc00F << 2)
>> +#define PHY_ISO_CMN_CTRL (0xc010 << 2)
>> +#define PHY_DP_TX_CTL (0xc408 << 2)
>> +#define PMA_CMN_CTRL1 (0xc800 << 2)
>> +#define PHY_PMA_ISO_CMN_CTRL (0xc810 << 2)
>> +#define PHY_ISOLATION_CTRL (0xc81f << 2)
>> +#define PHY_PMA_ISO_XCVR_CTRL(n) ((0xcc11 | ((n) << 6)) << 2)
>> +#define PHY_PMA_ISO_LINK_MODE(n) ((0xcc12 | ((n) << 6)) << 2)
>> +#define PHY_PMA_ISO_PWRST_CTRL(n) ((0xcc13 | ((n) << 6)) << 2)
>> +#define PHY_PMA_ISO_TX_DATA_LO(n) ((0xcc14 | ((n) << 6)) << 2)
>> +#define PHY_PMA_ISO_TX_DATA_HI(n) ((0xcc15 | ((n) << 6)) << 2)
>> +#define PHY_PMA_ISO_RX_DATA_LO(n) ((0xcc16 | ((n) << 6)) << 2)
>> +#define PHY_PMA_ISO_RX_DATA_HI(n) ((0xcc17 | ((n) << 6)) << 2)
>> +#define TX_BIST_CTRL(n) ((0x4140 | ((n) << 9)) << 2)
>> +#define TX_BIST_UDDWR(n) ((0x4141 | ((n) << 9)) << 2)
>> +
>> +/*
>> + * Selects which PLL clock will be driven on the analog high speed
>> + * clock 0: PLL 0 div 1
>> + * clock 1: PLL 1 div 2
>> + */
>> +#define CLK_PLL_CONFIG 0X30
>> +#define CLK_PLL_MASK 0x33
>> +
>> +#define CMN_READY BIT(0)
>> +
>> +#define DP_PLL_CLOCK_ENABLE BIT(2)
>> +#define DP_PLL_ENABLE BIT(0)
>> +#define DP_PLL_DATA_RATE_RBR ((2 << 12) | (4 << 8))
>> +#define DP_PLL_DATA_RATE_HBR ((2 << 12) | (4 << 8))
>> +#define DP_PLL_DATA_RATE_HBR2 ((1 << 12) | (2 << 8))
>> +
>> +#define DP_MODE_A0 BIT(4)
>> +#define DP_MODE_A2 BIT(6)
>> +#define DP_MODE_ENTER_A0 0xc101
>> +#define DP_MODE_ENTER_A2 0xc104
>> +
>> +#define PHY_MODE_SET_TIMEOUT 100000
>> +
>> +#define PIN_ASSIGN_C_E 0x51d9
>> +#define PIN_ASSIGN_D_F 0x5100
>> +
>> +#define MODE_DISCONNECT 0
>> +#define MODE_UFP_USB BIT(0)
>> +#define MODE_DFP_USB BIT(1)
>> +#define MODE_DFP_DP BIT(2)
>> +
>> +struct usb3phy_reg {
>> + u32 offset;
>> + u32 enable_bit;
>> + u32 write_enable;
>> +};
>> +
>> +struct rockchip_usb3phy_port_cfg {
>> + struct usb3phy_reg typec_conn_dir;
>> + struct usb3phy_reg usb3tousb2_en;
>> + struct usb3phy_reg external_psm;
>> + struct usb3phy_reg pipe_status;
>> +};
>> +
>> +struct rockchip_typec_phy {
>> + struct device *dev;
>> + void __iomem *base;
>> + struct extcon_dev *extcon;
>> + struct regmap *grf_regs;
>> + struct clk *clk_core;
>> + struct clk *clk_ref;
>> + struct reset_control *uphy_rst;
>> + struct reset_control *pipe_rst;
>> + struct reset_control *tcphy_rst;
>> + struct rockchip_usb3phy_port_cfg port_cfgs;
>> + /* mutex to protect access to individual PHYs */
>> + struct mutex lock;
>> +
>> + bool flip;
>> + u8 mode;
>> +};
>> +
>> +struct phy_reg {
>> + u16 value;
>> + u32 addr;
>> +};
>> +
>> +struct phy_reg usb3_pll_cfg[] = {
>> + { 0xf0, CMN_PLL0_VCOCAL_INIT },
>> + { 0x18, CMN_PLL0_VCOCAL_ITER },
>> + { 0xd0, CMN_PLL0_INTDIV },
>> + { 0x4a4a, CMN_PLL0_FRACDIV },
>> + { 0x34, CMN_PLL0_HIGH_THR },
>> + { 0x1ee, CMN_PLL0_SS_CTRL1 },
>> + { 0x7f03, CMN_PLL0_SS_CTRL2 },
>> + { 0x20, CMN_PLL0_DSM_DIAG },
>> + { 0, CMN_DIAG_PLL0_OVRD },
>> + { 0, CMN_DIAG_PLL0_FBH_OVRD },
>> + { 0, CMN_DIAG_PLL0_FBL_OVRD },
>> + { 0x7, CMN_DIAG_PLL0_V2I_TUNE },
>> + { 0x45, CMN_DIAG_PLL0_CP_TUNE },
>> + { 0x8, CMN_DIAG_PLL0_LF_PROG },
>> +};
>> +
>> +struct phy_reg dp_pll_cfg[] = {
>> + { 0xf0, CMN_PLL1_VCOCAL_INIT },
>> + { 0x18, CMN_PLL1_VCOCAL_ITER },
>> + { 0x30b9, CMN_PLL1_VCOCAL_START },
>> + { 0x21c, CMN_PLL1_INTDIV },
>> + { 0, CMN_PLL1_FRACDIV },
>> + { 0x5, CMN_PLL1_HIGH_THR },
>> + { 0x35, CMN_PLL1_SS_CTRL1 },
>> + { 0x7f1e, CMN_PLL1_SS_CTRL2 },
>> + { 0x20, CMN_PLL1_DSM_DIAG },
>> + { 0, CMN_PLLSM1_USER_DEF_CTRL },
>> + { 0, CMN_DIAG_PLL1_OVRD },
>> + { 0, CMN_DIAG_PLL1_FBH_OVRD },
>> + { 0, CMN_DIAG_PLL1_FBL_OVRD },
>> + { 0x6, CMN_DIAG_PLL1_V2I_TUNE },
>> + { 0x45, CMN_DIAG_PLL1_CP_TUNE },
>> + { 0x8, CMN_DIAG_PLL1_LF_PROG },
>> + { 0x100, CMN_DIAG_PLL1_PTATIS_TUNE1 },
>> + { 0x7, CMN_DIAG_PLL1_PTATIS_TUNE2 },
>> + { 0x4, CMN_DIAG_PLL1_INCLK_CTRL },
>> +};
>> +
>> +static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
>> +{
>> + u32 i, rdata;
>> +
>> + /*
>> + * cmn_ref_clk_sel = 3, select the 24Mhz for clk parent
>> + * cmn_psm_clk_dig_div = 2, set the clk division to 2
>> + */
>> + writel(0x830, tcphy->base + PMA_CMN_CTRL1);
>> + for (i = 0; i < 4; i++) {
>> + /*
>> + * The following PHY configuration assumes a 24 MHz reference
>> + * clock.
>> + */
>> + writel(0x90, tcphy->base + XCVR_DIAG_LANE_FCM_EN_MGN(i));
>> + writel(0x960, tcphy->base + TX_RCVDET_EN_TMR(i));
>> + writel(0x30, tcphy->base + TX_RCVDET_ST_TMR(i));
>> + }
>> +
>> + rdata = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
>> + rdata &= ~CLK_PLL_MASK;
>> + rdata |= CLK_PLL_CONFIG;
>> + writel(rdata, tcphy->base + CMN_DIAG_HSCLK_SEL);
>> +}
>> +
>> +static void tcphy_cfg_usb3_pll(struct rockchip_typec_phy *tcphy)
>> +{
>> + u32 i;
>> +
>> + /* load the configuration of PLL0 */
>> + for (i = 0; i < ARRAY_SIZE(usb3_pll_cfg); i++)
>> + writel(usb3_pll_cfg[i].value,
>> + tcphy->base + usb3_pll_cfg[i].addr);
>> +}
>> +
>> +static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy)
>> +{
>> + u32 i;
>> +
>> + /* set the default mode to RBR */
>> + writel(DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE | DP_PLL_DATA_RATE_RBR,
>> + tcphy->base + DP_CLK_CTL);
>> +
>> + /* load the configuration of PLL1 */
>> + for (i = 0; i < ARRAY_SIZE(dp_pll_cfg); i++)
>> + writel(dp_pll_cfg[i].value, tcphy->base + dp_pll_cfg[i].addr);
>> +}
>> +
>> +static void tcphy_tx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
>> +{
>> + writel(0x7799, tcphy->base + TX_PSC_A0(lane));
>> + writel(0x7798, tcphy->base + TX_PSC_A1(lane));
>> + writel(0x5098, tcphy->base + TX_PSC_A2(lane));
>> + writel(0x5098, tcphy->base + TX_PSC_A3(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
>> + writel(0xbf, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
>> +}
>> +
>> +static void tcphy_rx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
>> +{
>> + writel(0xa6fd, tcphy->base + RX_PSC_A0(lane));
>> + writel(0xa6fd, tcphy->base + RX_PSC_A1(lane));
>> + writel(0xa410, tcphy->base + RX_PSC_A2(lane));
>> + writel(0x2410, tcphy->base + RX_PSC_A3(lane));
>> + writel(0x23ff, tcphy->base + RX_PSC_CAL(lane));
>> + writel(0x13, tcphy->base + RX_SIGDET_HL_FILT_TMR(lane));
>> + writel(0x03e7, tcphy->base + RX_REE_CTRL_DATA_MASK(lane));
>> + writel(0x1004, tcphy->base + RX_DIAG_SIGDET_TUNE(lane));
>> + writel(0x2010, tcphy->base + RX_PSC_RDY(lane));
>> + writel(0xfb, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
>> +}
>> +
>> +static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
>> +{
>> + u16 rdata;
>> +
>> + writel(0xbefc, tcphy->base + XCVR_PSM_RCTRL(lane));
>> + writel(0x6799, tcphy->base + TX_PSC_A0(lane));
>> + writel(0x6798, tcphy->base + TX_PSC_A1(lane));
>> + writel(0x98, tcphy->base + TX_PSC_A2(lane));
>> + writel(0x98, tcphy->base + TX_PSC_A3(lane));
>> +
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_001(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_010(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_011(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_100(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_101(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_110(lane));
>> + writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_111(lane));
>> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_10(lane));
>> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_01(lane));
>> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
>> + writel(0, tcphy->base + TX_TXCC_CPOST_MULT_11(lane));
>> +
>> + writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
>> + writel(0x400, tcphy->base + TX_DIAG_TX_DRV(lane));
>> +
>> + rdata = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
>> + rdata = (rdata & 0x8fff) | 0x6000;
>> + writel(rdata, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
>> +}
>> +
>> +static inline int property_enable(struct rockchip_typec_phy *tcphy,
>> + const struct usb3phy_reg *reg, bool en)
>> +{
>> + u32 mask = 1 << reg->write_enable;
>> + u32 val = en << reg->enable_bit;
>> +
>> + return regmap_write(tcphy->grf_regs, reg->offset, val | mask);
>> +}
>> +
>> +static void tcphy_dp_aux_calibration(struct rockchip_typec_phy *tcphy)
>> +{
>> + u16 rdata, rdata2, val;
>> +
>> + /* disable txda_cal_latch_en for rewrite the calibration values */
>> + rdata = readl(tcphy->base + TX_ANA_CTRL_REG_1);
>> + val = rdata & 0xdfff;
>> + writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
>> +
>> + /*
>> + * read a resistor calibration code from CMN_TXPUCAL_CTRL[6:0] and
>> + * write it to TX_DIG_CTRL_REG_2[6:0], and delay 1ms to make sure it
>> + * works.
>> + */
>> + rdata = readl(tcphy->base + TX_DIG_CTRL_REG_2);
>> + rdata = rdata & 0xffc0;
>> +
>> + rdata2 = readl(tcphy->base + CMN_TXPUCAL_CTRL);
>> + rdata2 = rdata2 & 0x3f;
>> +
>> + val = rdata | rdata2;
>> + writel(val, tcphy->base + TX_DIG_CTRL_REG_2);
>> + usleep_range(1000, 1050);
>> +
>> + /*
>> + * Enable signal for latch that sample and holds calibration values.
>> + * Activate this signal for 1 clock cycle to sample new calibration
>> + * values.
>> + */
>> + rdata = readl(tcphy->base + TX_ANA_CTRL_REG_1);
>> + val = rdata | 0x2000;
>> + writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
>> + usleep_range(150, 200);
>> +
>> + /* set TX Voltage Level and TX Deemphasis to 0 */
>> + writel(0, tcphy->base + PHY_DP_TX_CTL);
>> + /* re-enable decap */
>> + writel(0x100, tcphy->base + TX_ANA_CTRL_REG_2);
>> + writel(0x300, tcphy->base + TX_ANA_CTRL_REG_2);
>> + writel(0x2008, tcphy->base + TX_ANA_CTRL_REG_1);
>> + writel(0x2018, tcphy->base + TX_ANA_CTRL_REG_1);
>> +
>> + writel(0, tcphy->base + TX_ANA_CTRL_REG_5);
>> +
>> + /*
>> + * Programs txda_drv_ldo_prog[15:0], Sets driver LDO
>> + * voltage 16'h1001 for DP-AUX-TX and RX
>> + */
>> + writel(0x1001, tcphy->base + TX_ANA_CTRL_REG_4);
>> +
>> + /* re-enables Bandgap reference for LDO */
>> + writel(0x2098, tcphy->base + TX_ANA_CTRL_REG_1);
>> + writel(0x2198, tcphy->base + TX_ANA_CTRL_REG_1);
>> +
>> + /*
>> + * re-enables the transmitter pre-driver, driver data selection MUX,
>> + * and receiver detect circuits.
>> + */
>> + writel(0x301, tcphy->base + TX_ANA_CTRL_REG_2);
>> + writel(0x303, tcphy->base + TX_ANA_CTRL_REG_2);
>> +
>> + /*
>> + * BIT 12: Controls auxda_polarity, which selects the polarity of the
>> + * xcvr:
>> + * 1, Reverses the polarity (If TYPEC, Pulls ups aux_p and pull
>> + * down aux_m)
>> + * 0, Normal polarity (if TYPE_C, pulls up aux_m and pulls down
>> + * aux_p)
>> + */
>> + val = 0xa078;
>> + if (!tcphy->flip)
>> + val |= BIT(12);
>> + writel(val, tcphy->base + TX_ANA_CTRL_REG_1);
>> +
>> + writel(0, tcphy->base + TX_ANA_CTRL_REG_3);
>> + writel(0, tcphy->base + TX_ANA_CTRL_REG_4);
>> + writel(0, tcphy->base + TX_ANA_CTRL_REG_5);
>> +
>> + /*
>> + * Controls low_power_swing_en, set the voltage swing of the driver
>> + * to 400mv. The values below are peak to peak (differential) values.
>> + */
>> + writel(4, tcphy->base + TXDA_COEFF_CALC_CTRL);
>> + writel(0, tcphy->base + TXDA_CYA_AUXDA_CYA);
>> +
>> + /* Controls tx_high_z_tm_en */
>> + val = readl(tcphy->base + TX_DIG_CTRL_REG_2);
>> + val |= BIT(15);
>> + writel(val, tcphy->base + TX_DIG_CTRL_REG_2);
>> +}
>> +
>> +static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
>> +{
>> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
>> + int ret, i;
>> + u32 val;
>> +
>> + ret = clk_prepare_enable(tcphy->clk_core);
>> + if (ret) {
>> + dev_err(tcphy->dev, "Failed to prepare_enable core clock\n");
>> + return ret;
>> + }
>> +
>> + ret = clk_prepare_enable(tcphy->clk_ref);
>> + if (ret) {
>> + dev_err(tcphy->dev, "Failed to prepare_enable ref clock\n");
>> + goto err_clk_core;
>> + }
>> +
>> + reset_control_deassert(tcphy->tcphy_rst);
>> +
>> + property_enable(tcphy, &cfg->typec_conn_dir, tcphy->flip);
>> +
>> + tcphy_cfg_24m(tcphy);
>> +
>> + if (mode == MODE_DFP_DP) {
>> + tcphy_cfg_dp_pll(tcphy);
>> + for (i = 0; i < 4; i++)
>> + tcphy_dp_cfg_lane(tcphy, i);
>> +
>> + writel(PIN_ASSIGN_C_E, tcphy->base + PMA_LANE_CFG);
>> + } else {
>> + tcphy_cfg_usb3_pll(tcphy);
>> + tcphy_cfg_dp_pll(tcphy);
>> + if (tcphy->flip) {
>> + tcphy_tx_usb3_cfg_lane(tcphy, 3);
>> + tcphy_rx_usb3_cfg_lane(tcphy, 2);
>> + tcphy_dp_cfg_lane(tcphy, 0);
>> + tcphy_dp_cfg_lane(tcphy, 1);
>> + } else {
>> + tcphy_tx_usb3_cfg_lane(tcphy, 0);
>> + tcphy_rx_usb3_cfg_lane(tcphy, 1);
>> + tcphy_dp_cfg_lane(tcphy, 2);
>> + tcphy_dp_cfg_lane(tcphy, 3);
>> + }
>> +
>> + writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG);
>> + }
>> +
>> + writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
>> +
>> + reset_control_deassert(tcphy->uphy_rst);
>> +
>> + ret = readx_poll_timeout(readl, tcphy->base + PMA_CMN_CTRL1,
>> + val, val & CMN_READY, 10,
>> + PHY_MODE_SET_TIMEOUT);
>> + if (ret < 0) {
>> + dev_err(tcphy->dev, "wait pma ready timeout\n");
>> + ret = -ETIMEDOUT;
>> + goto err_wait_pma;
>> + }
>> +
>> + reset_control_deassert(tcphy->pipe_rst);
>> +
>> + return 0;
>> +
>> +err_wait_pma:
>> + reset_control_assert(tcphy->uphy_rst);
>> + reset_control_assert(tcphy->tcphy_rst);
>> + clk_disable_unprepare(tcphy->clk_ref);
>> +err_clk_core:
>> + clk_disable_unprepare(tcphy->clk_core);
>> + return ret;
>> +}
>> +
>> +static void tcphy_phy_deinit(struct rockchip_typec_phy *tcphy)
>> +{
>> + reset_control_assert(tcphy->tcphy_rst);
>> + reset_control_assert(tcphy->uphy_rst);
>> + reset_control_assert(tcphy->pipe_rst);
>> + clk_disable_unprepare(tcphy->clk_core);
>> + clk_disable_unprepare(tcphy->clk_ref);
>> +}
>> +
>> +static int tcphy_get_mode(struct rockchip_typec_phy *tcphy)
>> +{
>> + struct extcon_dev *edev = tcphy->extcon;
>> + union extcon_property_value property;
>> + unsigned int id;
>> + bool dfp, ufp, dp;
>> + u8 mode;
>> + int ret;
>> +
>> + ufp = extcon_get_state(edev, EXTCON_USB);
>> + dfp = extcon_get_state(edev, EXTCON_USB_HOST);
>> + dp = extcon_get_state(edev, EXTCON_DISP_DP);
>> +
>> + mode = MODE_DFP_USB;
>> + id = EXTCON_USB_HOST;
>> +
>> + if (ufp) {
>> + mode = MODE_UFP_USB;
>> + id = EXTCON_USB;
>> + } else if (dp) {
>> + mode = MODE_DFP_DP;
>> + id = EXTCON_DISP_DP;
>> +
>> + ret = extcon_get_property(edev, id, EXTCON_PROP_USB_SUPERSPEED,
>> + &property);
>> + if (ret) {
>> + dev_err(tcphy->dev, "get superspeed property failed\n");
>> + return ret;
>> + }
>> +
>> + if (property.intval)
>> + mode |= MODE_DFP_USB;
>> + }
>> +
>> + ret = extcon_get_property(edev, id, EXTCON_PROP_USB_TYPEC_POLARITY,
>> + &property);
>> + if (ret) {
>> + dev_err(tcphy->dev, "get polarity property failed\n");
>> + return ret;
>> + }
>> +
>> + tcphy->flip = property.intval ? 1 : 0;
>> +
>> + return mode;
>> +}
>> +
>> +static int rockchip_usb3_phy_power_on(struct phy *phy)
>> +{
>> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
>> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
>> + const struct usb3phy_reg *reg = &cfg->pipe_status;
>> + int timeout, new_mode, ret = 0;
>> + u32 val;
>> +
>> + mutex_lock(&tcphy->lock);
>> +
>> + new_mode = tcphy_get_mode(tcphy);
>> + if (new_mode < 0) {
>> + ret = new_mode;
>> + goto unlock_ret;
>> + }
>> +
>> + /* DP-only mode; fall back to USB2 */
>> + if (!(new_mode & (MODE_DFP_USB | MODE_UFP_USB)))
>> + goto unlock_ret;
>> +
>> + if (tcphy->mode == new_mode)
>> + goto unlock_ret;
>> +
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + tcphy_phy_init(tcphy, new_mode);
>> +
>> + /* wait TCPHY for pipe ready */
>> + for (timeout = 0; timeout < 100; timeout++) {
>> + regmap_read(tcphy->grf_regs, reg->offset, &val);
>> + if (!(val & BIT(reg->enable_bit))) {
>> + tcphy->mode |= new_mode & (MODE_DFP_USB | MODE_UFP_USB);
>> + goto unlock_ret;
>> + }
>> + usleep_range(10, 20);
>> + }
>> +
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + tcphy_phy_deinit(tcphy);
>> +
>> + ret = -ETIMEDOUT;
>> +
>> +unlock_ret:
>> + mutex_unlock(&tcphy->lock);
>> + return ret;
>> +}
>> +
>> +static int rockchip_usb3_phy_power_off(struct phy *phy)
>> +{
>> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
>> +
>> + mutex_lock(&tcphy->lock);
>> +
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + goto unlock;
>> +
>> + tcphy->mode &= ~(MODE_UFP_USB | MODE_DFP_USB);
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + tcphy_phy_deinit(tcphy);
>> +
>> +unlock:
>> + mutex_unlock(&tcphy->lock);
>> + return 0;
>> +}
>> +
>> +static const struct phy_ops rockchip_usb3_phy_ops = {
>> + .power_on = rockchip_usb3_phy_power_on,
>> + .power_off = rockchip_usb3_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int rockchip_dp_phy_power_on(struct phy *phy)
>> +{
>> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
>> + int new_mode, ret = 0;
>> + u32 val;
>> +
>> + mutex_lock(&tcphy->lock);
>> +
>> + new_mode = tcphy_get_mode(tcphy);
>> + if (new_mode < 0) {
>> + ret = new_mode;
>> + goto unlock_ret;
>> + }
>> +
>> + if (!(new_mode & MODE_DFP_DP)) {
>> + ret = -ENODEV;
>> + goto unlock_ret;
>> + }
>> +
>> + if (tcphy->mode == new_mode)
>> + goto unlock_ret;
>> +
>> + /*
>> + * If the PHY has been power on, but the mode is not DP only mode,
>> + * re-init the PHY for setting all of 4 lanes to DP.
>> + */
>> + if (new_mode == MODE_DFP_DP && tcphy->mode != MODE_DISCONNECT) {
>> + tcphy_phy_deinit(tcphy);
>> + tcphy_phy_init(tcphy, new_mode);
>> + } else if (tcphy->mode == MODE_DISCONNECT) {
>> + tcphy_phy_init(tcphy, new_mode);
>> + }
>> +
>> + ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
>> + val, val & DP_MODE_A2, 1000,
>> + PHY_MODE_SET_TIMEOUT);
>> + if (ret < 0) {
>> + dev_err(tcphy->dev, "failed to wait TCPHY enter A2\n");
>> + goto power_on_finish;
>> + }
>> +
>> + tcphy_dp_aux_calibration(tcphy);
>> +
>> + writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL);
>> +
>> + ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
>> + val, val & DP_MODE_A0, 1000,
>> + PHY_MODE_SET_TIMEOUT);
>> + if (ret < 0) {
>> + writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
>> + dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n");
>> + goto power_on_finish;
>> + }
>> +
>> + tcphy->mode |= MODE_DFP_DP;
>> +
>> +power_on_finish:
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + tcphy_phy_deinit(tcphy);
>> +unlock_ret:
>> + mutex_unlock(&tcphy->lock);
>> + return ret;
>> +}
>> +
>> +static int rockchip_dp_phy_power_off(struct phy *phy)
>> +{
>> + struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
>> +
>> + mutex_lock(&tcphy->lock);
>> +
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + goto unlock;
>> +
>> + tcphy->mode &= ~MODE_DFP_DP;
>> +
>> + writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
>> +
>> + if (tcphy->mode == MODE_DISCONNECT)
>> + tcphy_phy_deinit(tcphy);
>> +
>> +unlock:
>> + mutex_unlock(&tcphy->lock);
>> + return 0;
>> +}
>> +
>> +static const struct phy_ops rockchip_dp_phy_ops = {
>> + .power_on = rockchip_dp_phy_power_on,
>> + .power_off = rockchip_dp_phy_power_off,
>> + .owner = THIS_MODULE,
>> +};
>> +
>> +static int tcphy_get_param(struct device *dev,
>> + struct usb3phy_reg *reg,
>> + const char *name)
>> +{
>> + u32 buffer[3];
>> + int ret;
>> +
>> + ret = of_property_read_u32_array(dev->of_node, name, buffer, 3);
>> + if (ret) {
>> + dev_err(dev, "Can not parse %s\n", name);
>> + return ret;
>> + }
>> +
>> + reg->offset = buffer[0];
>> + reg->enable_bit = buffer[1];
>> + reg->write_enable = buffer[2];
>> + return 0;
>> +}
>> +
>> +static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
>> + struct device *dev)
>> +{
>> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
>> + int ret;
>> +
>> + ret = tcphy_get_param(dev, &cfg->typec_conn_dir,
>> + "rockchip,typec-conn-dir");
>> + if (ret)
>> + return ret;
>> +
>> + ret = tcphy_get_param(dev, &cfg->usb3tousb2_en,
>> + "rockchip,usb3tousb2-en");
>> + if (ret)
>> + return ret;
>> +
>> + ret = tcphy_get_param(dev, &cfg->external_psm,
>> + "rockchip,external-psm");
>> + if (ret)
>> + return ret;
>> +
>> + ret = tcphy_get_param(dev, &cfg->pipe_status,
>> + "rockchip,pipe-status");
>> + if (ret)
>> + return ret;
>> +
>> + tcphy->grf_regs = syscon_regmap_lookup_by_phandle(dev->of_node,
>> + "rockchip,grf");
>> + if (IS_ERR(tcphy->grf_regs)) {
>> + dev_err(dev, "could not find grf dt node\n");
>> + return PTR_ERR(tcphy->grf_regs);
>> + }
>> +
>> + tcphy->clk_core = devm_clk_get(dev, "tcpdcore");
>> + if (IS_ERR(tcphy->clk_core)) {
>> + dev_err(dev, "could not get uphy core clock\n");
>> + return PTR_ERR(tcphy->clk_core);
>> + }
>> +
>> + tcphy->clk_ref = devm_clk_get(dev, "tcpdphy-ref");
>> + if (IS_ERR(tcphy->clk_ref)) {
>> + dev_err(dev, "could not get uphy ref clock\n");
>> + return PTR_ERR(tcphy->clk_ref);
>> + }
>> +
>> + tcphy->uphy_rst = devm_reset_control_get(dev, "uphy");
>> + if (IS_ERR(tcphy->uphy_rst)) {
>> + dev_err(dev, "no uphy_rst reset control found\n");
>> + return PTR_ERR(tcphy->uphy_rst);
>> + }
>> +
>> + tcphy->pipe_rst = devm_reset_control_get(dev, "uphy-pipe");
>> + if (IS_ERR(tcphy->pipe_rst)) {
>> + dev_err(dev, "no pipe_rst reset control found\n");
>> + return PTR_ERR(tcphy->pipe_rst);
>> + }
>> +
>> + tcphy->tcphy_rst = devm_reset_control_get(dev, "uphy-tcphy");
>> + if (IS_ERR(tcphy->tcphy_rst)) {
>> + dev_err(dev, "no tcphy_rst reset control found\n");
>> + return PTR_ERR(tcphy->tcphy_rst);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static void typec_phy_pre_init(struct rockchip_typec_phy *tcphy)
>> +{
>> + struct rockchip_usb3phy_port_cfg *cfg = &tcphy->port_cfgs;
>> +
>> + reset_control_assert(tcphy->tcphy_rst);
>> + reset_control_assert(tcphy->uphy_rst);
>> + reset_control_assert(tcphy->pipe_rst);
>> +
>> + /* select external psm clock */
>> + property_enable(tcphy, &cfg->external_psm, 1);
>> + property_enable(tcphy, &cfg->usb3tousb2_en, 0);
>> +
>> + tcphy->mode = MODE_DISCONNECT;
>> +}
>> +
>> +static int rockchip_typec_phy_probe(struct platform_device *pdev)
>> +{
>> + struct device *dev = &pdev->dev;
>> + struct device_node *np = dev->of_node;
>> + struct device_node *child_np;
>> + struct rockchip_typec_phy *tcphy;
>> + struct phy_provider *phy_provider;
>> + struct resource *res;
>> + int ret;
>> +
>> + tcphy = devm_kzalloc(dev, sizeof(*tcphy), GFP_KERNEL);
>> + if (!tcphy)
>> + return -ENOMEM;
>> +
>> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> + tcphy->base = devm_ioremap_resource(dev, res);
>> + if (IS_ERR(tcphy->base))
>> + return PTR_ERR(tcphy->base);
>> +
>> + ret = tcphy_parse_dt(tcphy, dev);
>> + if (ret)
>> + return ret;
>> +
>> + tcphy->dev = dev;
>> + platform_set_drvdata(pdev, tcphy);
>> + mutex_init(&tcphy->lock);
>> +
>> + typec_phy_pre_init(tcphy);
>> +
>> + tcphy->extcon = extcon_get_edev_by_phandle(dev, 0);
>> + if (IS_ERR(tcphy->extcon)) {
>> + if (PTR_ERR(tcphy->extcon) != -EPROBE_DEFER)
>> + dev_err(dev, "Invalid or missing extcon\n");
>> + return PTR_ERR(tcphy->extcon);
>> + }
>> +
>> + for_each_available_child_of_node(np, child_np) {
>> + struct phy *phy;
>> +
>> + if (!of_node_cmp(child_np->name, "dp-port"))
>> + phy = devm_phy_create(dev, child_np,
>> + &rockchip_dp_phy_ops);
>> + else if (!of_node_cmp(child_np->name, "usb3-port"))
>> + phy = devm_phy_create(dev, child_np,
>> + &rockchip_usb3_phy_ops);
>> + else
>> + continue;
>> +
>> + if (IS_ERR(phy)) {
>> + dev_err(dev, "failed to create phy: %s\n",
>> + child_np->name);
>> + return PTR_ERR(phy);
>> + }
>> +
>> + phy_set_drvdata(phy, tcphy);
>> + }
>> +
>> + phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
>> + if (IS_ERR(phy_provider)) {
>> + dev_err(dev, "Failed to register phy provider\n");
>> + return PTR_ERR(phy_provider);
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id rockchip_typec_phy_dt_ids[] = {
>> + { .compatible = "rockchip,rk3399-typec-phy" },
>> + {}
>> +};
>> +
>> +MODULE_DEVICE_TABLE(of, rockchip_typec_phy_dt_ids);
>> +
>> +static struct platform_driver rockchip_typec_phy_driver = {
>> + .probe = rockchip_typec_phy_probe,
>> + .driver = {
>> + .name = "rockchip-typec-phy",
>> + .of_match_table = rockchip_typec_phy_dt_ids,
>> + },
>> +};
>> +
>> +module_platform_driver(rockchip_typec_phy_driver);
>> +
>> +MODULE_AUTHOR("Chris Zhong <zyw at rock-chips.com>");
>> +MODULE_AUTHOR("Kever Yang <kever.yang at rock-chips.com>");
>> +MODULE_DESCRIPTION("Rockchip USB TYPE-C PHY driver");
>> +MODULE_LICENSE("GPL v2");
>>
>
More information about the linux-arm-kernel
mailing list