[PATCH 6/7] arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board
Chanwoo Choi
cw00.choi at samsung.com
Thu Aug 18 18:01:48 PDT 2016
Hi Rob,
On 2016년 08월 19일 04:08, Rob Herring wrote:
> On Tue, Aug 16, 2016 at 03:35:27PM +0900, Chanwoo Choi wrote:
>> This patch adds the Device Tree source for Exynos5433-based Samsung TM2 board.
>> This board fully support the all things for mobile target.
>>
>> This patch supports the following devices:
>> 1. basic SoC
>> - Initial booting for Samsung Exynos5433 SoC
>> - DRAM LPDDR3 (3GB)
>> - eMMC (32GB)
>> - ARM architecture timer
>>
>> 2. power management devices
>> - Sasmung S2MPS13 PMIC for the power supply
>> - CPUFREQ for big.LITTLE cores
>> - TMU for big.LITTLE cores and GPU
>> - ADC with thermistor to measure the temperature of AP/Battery/Charger
>> - Maxim MAX77843 Interface PMIC (MUIC/Fuel-gauge/Charger/Haptic/LED/Regulator)
>>
>> 3. sound devices
>> - I2S for sound bus
>> - LPASS for sound power control
>> - Wolfson WM5110 for sound codec
>> - Maxim MAX98504 for speaker amplifier
>> - TM2 ASoC Machine device driver node
>>
>> 3. display devices
>> - DECON, DSI and MIC for the panel output
>>
>> 4. usb devices
>> - USB 3.0 DRD (Dual Role Device)
>> - USB 3.0 Host controller
>>
>> 5. storage devices
>> - MSHC (obile Storae Host Controller) for eMMC device
>>
>> 6. misc devices
>> - gpio-keys (power, volume up/down, home key)
>> - PWM (Pulse Width Modulation Timer)
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi at samsung.com>
>> Signed-off-by: Jaehoon Chung <jh80.chung at samsung.com>
>> Signed-off-by: Seung-Woo Kim <sw0312.kim at samsung.com>
>> Signed-off-by: Joonyoung Shim <jy0922.shim at samsung.com>
>> Signed-off-by: Inki Dae <inki.dae at samsung.com>
>> Signed-off-by: Jonghwa Lee <jonghwa3.lee at samsung.com>
>> Signed-off-by: Beomho Seo <beomho.seo at samsung.com>
>> Signed-off-by: Jaewon Kim <jaewon02.kim at samsung.com>
>> Signed-off-by: Hyungwon Hwang <human.hwang at samsung.com>
>> Signed-off-by: Inha Song <ideal.song at samsung.com>
>> Signed-off-by: Ingi kim <ingi2.kim at samsung.com>
>> Signed-off-by: Krzysztof Kozlowski <k.kozlowski at samsung.com>
>> Signed-off-by: Marek Szyprowski <m.szyprowski at samsung.com>
>> Signed-off-by: Andrzej Hajda <a.hajda at samsung.com>
>> Signed-off-by: Sylwester Nawrocki <s.nawrocki at samsung.com>
>> ---
>> .../bindings/arm/samsung/samsung-boards.txt | 1 +
>> arch/arm64/boot/dts/exynos/Makefile | 5 +-
>> arch/arm64/boot/dts/exynos/exynos5433-tm2.dts | 1003 ++++++++++++++++++++
>> 3 files changed, 1008 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
>>
>> diff --git a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> index 0ea7f14ef294..c704b4bf6137 100644
>> --- a/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> +++ b/Documentation/devicetree/bindings/arm/samsung/samsung-boards.txt
>> @@ -15,6 +15,7 @@ Required root node properties:
>> - "samsung,xyref5260" - for Exynos5260-based Samsung board.
>> - "samsung,smdk5410" - for Exynos5410-based Samsung SMDK5410 eval board.
>> - "samsung,smdk5420" - for Exynos5420-based Samsung SMDK5420 eval board.
>> + - "samsung,tm2" - for Exynos5333-based Samsung TM2 board.
>> - "samsung,sd5v1" - for Exynos5440-based Samsung board.
>> - "samsung,ssdk5440" - for Exynos5440-based Samsung board.
>>
>> diff --git a/arch/arm64/boot/dts/exynos/Makefile b/arch/arm64/boot/dts/exynos/Makefile
>> index 50c9b9383cfa..7ddea53769a7 100644
>> --- a/arch/arm64/boot/dts/exynos/Makefile
>> +++ b/arch/arm64/boot/dts/exynos/Makefile
>> @@ -1,4 +1,7 @@
>> -dtb-$(CONFIG_ARCH_EXYNOS) += exynos7-espresso.dtb
>> +dtb-$(CONFIG_ARCH_EXYNOS) += \
>> + exynos5433-tm2.dtb \
>> + exynos5433-tm2e.dtb \
>> + exynos7-espresso.dtb
>>
>> always := $(dtb-y)
>> subdir-y := $(dts-dirs)
>> diff --git a/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
>> new file mode 100644
>> index 000000000000..3e497b0d0015
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/exynos/exynos5433-tm2.dts
>> @@ -0,0 +1,1003 @@
>> +/*
>> + * SAMSUNG Exynos5433 TM2 board device tree source
>> + *
>> + * Copyright (c) 2016 Samsung Electronics Co., Ltd.
>> + *
>> + * Device tree source file for Samsung's TM2 board which is based on
>> + * Samsung Exynos5433 SoC.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +/dts-v1/;
>> +#include "exynos5433.dtsi"
>> +#include <dt-bindings/gpio/gpio.h>
>> +#include <dt-bindings/input/input.h>
>> +
>> +/ {
>> + model = "Samsung TM2 board";
>> + compatible = "samsung,exynos5433-tm2", "samsung,exynos5433";
>> +
>> + aliases {
>> + i2c0 = &hsi2c_0;
>> + i2c1 = &hsi2c_1;
>> + i2c2 = &hsi2c_2;
>> + i2c3 = &hsi2c_3;
>> + i2c4 = &hsi2c_4;
>> + i2c5 = &hsi2c_5;
>> + i2c6 = &hsi2c_6;
>> + i2c7 = &hsi2c_7;
>> + i2c8 = &hsi2c_8;
>> + i2c9 = &hsi2c_9;
>> + i2c10 = &hsi2c_10;
>> + i2c11 = &hsi2c_11;
>> + mshc0 = &mshc_0;
>> + mshc1 = &mshc_1;
>> + mshc2 = &mshc_2;
>> + pinctrl0 = &pinctrl_alive;
>> + pinctrl1 = &pinctrl_aud;
>> + pinctrl2 = &pinctrl_cpif;
>> + pinctrl3 = &pinctrl_ese;
>> + pinctrl4 = &pinctrl_finger;
>> + pinctrl5 = &pinctrl_fsys;
>> + pinctrl6 = &pinctrl_imem;
>> + pinctrl7 = &pinctrl_nfc;
>> + pinctrl8 = &pinctrl_peric;
>> + pinctrl9 = &pinctrl_touch;
>> + serial0 = &serial_0;
>> + serial1 = &serial_1;
>> + serial2 = &serial_2;
>> + serial3 = &serial_3;
>> + spi0 = &spi_0;
>> + spi1 = &spi_1;
>> + spi2 = &spi_2;
>> + spi3 = &spi_3;
>> + spi4 = &spi_4;
>> + usbdrdphy0 = &usbdrd30_phy;
>
> Please drop all these aliases except for serial.
I'll remain the pinctrl/spi/serial and then drop the else aliases.
The alias id pinctrl/spi/serial are used.
>
>> + };
>> +
>> + chosen {
>> + stdout-path = &serial_1;
>> + };
>> +
>> + memory at 20000000 {
>> + device_type = "memory";
>> + reg = <0x0 0x20000000 0x0 0xc0000000>;
>> + };
>> +
>> + gpio_keys {
>
> Use -, not _.
OK.
>> + compatible = "gpio-keys";
>> +
>> + power_key {
>
> ditto...
OK.
>
>> + gpios = <&gpa2 7 1>;
>> + linux,code = <KEY_POWER>;
>> + label = "power key";
>> + debounce-interval = <10>;
>> + gpio-key,wakeup;
>
> This is legacy. Use the common binding.
I'll remove it.
>
>> + };
>> +
>> + volume_up_key {
>> + gpios = <&gpa2 0 1>;
>> + linux,code = <KEY_VOLUMEUP>;
>> + label = "volume-up key";
>> + debounce-interval = <10>;
>> + };
>> +
>> + volume_down_key {
>> + gpios = <&gpa2 1 1>;
>> + linux,code = <KEY_VOLUMEDOWN>;
>> + label = "volume-down key";
>> + debounce-interval = <10>;
>> + };
>> +
>> + homepage_key {
>> + gpios = <&gpa0 3 1>;
>> + linux,code = <KEY_MENU>;
>> + label = "homepage key";
>> + debounce-interval = <10>;
>> + };
>> + };
>> +
>> + i2c_max98504: i2c-gpio-0 {
>> + compatible = "i2c-gpio";
>> + gpios = <&gpd0 1 GPIO_ACTIVE_HIGH /* SPK_AMP_SDA */
>> + &gpd0 0 GPIO_ACTIVE_HIGH /* SPK_AMP_SCL */ >;
>> + i2c-gpio,delay-us = <2>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + status = "okay";
>> +
>> + max98504: max98504 at 31 {
>> + compatible = "maxim,max98504";
>> + reg = <0x31>;
>> + maxim,rx-path = <1>;
>> + maxim,tx-path = <1>;
>> + maxim,tx-channel-mask = <3>;
>> + maxim,tx-channel-source = <2>;
>> + };
>> + };
>> +
>> + sound {
>> + compatible = "samsung,tm2-audio";
>> + audio-codec = <&wm5110>;
>> + i2s-controller = <&i2s0>;
>> + audio-amplifier = <&max98504>;
>> + mic-bias-gpios = <&gpr3 2 0>;
>> + model = "wm5110";
>> + samsung,audio-routing =
>> + /* Headphone */
>> + "HP", "HPOUT1L",
>> + "HP", "HPOUT1R",
>> +
>> + /* Speaker */
>> + "SPK", "SPKOUT",
>> + "SPKOUT", "HPOUT2L",
>> + "SPKOUT", "HPOUT2R",
>> +
>> + /* Receiver */
>> + "RCV", "HPOUT3L",
>> + "RCV", "HPOUT3R";
>> + status = "okay";
>> + };
>> +};
>> +
>> +&adc {
>> + vdd-supply = <&ldo3_reg>;
>> + status = "okay";
>> +
>> + thermistor-ap {
>> + compatible = "ntc,ncp03wf104";
>> + pullup-uv = <1800000>;
>> + pullup-ohm = <100000>;
>> + pulldown-ohm = <0>;
>> + io-channels = <&adc 0>;
>> + };
>> +
>> + thermistor_battery: thermistor-battery {
>> + compatible = "ntc,ncp03wf104";
>> + pullup-uv = <1800000>;
>> + pullup-ohm = <100000>;
>> + pulldown-ohm = <0>;
>> + io-channels = <&adc 1>;
>> + #thermal-sensor-cells = <0>;
>> + };
>> +
>> + thermistor-charger {
>> + compatible = "ntc,ncp03wf104";
>> + pullup-uv = <1800000>;
>> + pullup-ohm = <100000>;
>> + pulldown-ohm = <0>;
>> + io-channels = <&adc 2>;
>> + };
>> +};
>> +
>> +&cpu0 {
>> + cpu-supply = <&buck3_reg>;
>> +};
>> +
>> +&cpu4 {
>> + cpu-supply = <&buck2_reg>;
>> +};
>> +
>> +&decon {
>> + status = "okay";
>> + iommu-reserved-mapping = <0x20000000 0x20000000 0xc0000000>;
>> +
>> + i80-if-timings {
>> + };
>> +};
>> +
>> +&dsi {
>> + status = "okay";
>> + vddcore-supply = <&ldo6_reg>;
>> + vddio-supply = <&ldo7_reg>;
>> + samsung,pll-clock-frequency = <24000000>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&te_irq>;
>> +
>> + ports {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>> + port at 1 {
>> + reg = <1>;
>> +
>> + dsi_out: endpoint {
>> + samsung,burst-clock-frequency = <512000000>;
>> + samsung,esc-clock-frequency = <16000000>;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&hsi2c_0 {
>> + status = "okay";
>> + clock-frequency = <2500000>;
>> +
>> + s2mps13_pmic at 66 {
>
> Use '-'
OK.
>
>> + compatible = "samsung,s2mps13-pmic";
>> + interrupt-parent = <&gpa0>;
>> + interrupts = <7 0>;
>> + reg = <0x66>;
>> + wakeup;
>
> Use the common binding.
I'll remove it.
>
>> + samsung,s2mps11-wrstbi-ground;
>> +
>> + s2mps13_osc: clocks {
>> + compatible = "samsung,s2mps13-clk";
>> + #clock-cells = <1>;
>> + clock-output-names = "s2mps13_ap", "s2mps13_cp",
>> + "s2mps13_bt";
>> + };
>> +
>> + regulators {
>> + ldo1_reg: LDO1 {
>> + regulator-name = "VDD_ALIVE_0.9V_AP";
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <900000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo2_reg: LDO2 {
>> + regulator-name = "VDDQ_MMC2_2.8V_AP";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo3_reg: LDO3 {
>> + regulator-name = "VDD1_E_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo4_reg: LDO4 {
>> + regulator-name = "VDD10_MIF_PLL_1.0V_AP";
>> + regulator-min-microvolt = <1300000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo5_reg: LDO5 {
>> + regulator-name = "VDD10_DPLL_1.0V_AP";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo6_reg: LDO6 {
>> + regulator-name = "VDD10_MIPI2L_1.0V_AP";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo7_reg: LDO7 {
>> + regulator-name = "VDD18_MIPI2L_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo8_reg: LDO8 {
>> + regulator-name = "VDD18_LLI_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo9_reg: LDO9 {
>> + regulator-name = "VDD18_ABB_ETC_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo10_reg: LDO10 {
>> + regulator-name = "VDD33_USB30_3.0V_AP";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo11_reg: LDO11 {
>> + regulator-name = "VDD_INT_M_1.0V_AP";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo12_reg: LDO12 {
>> + regulator-name = "VDD_KFC_M_1.1V_AP";
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <1350000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo13_reg: LDO13 {
>> + regulator-name = "VDD_G3D_M_0.95V_AP";
>> + regulator-min-microvolt = <950000>;
>> + regulator-max-microvolt = <950000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo14_reg: LDO14 {
>> + regulator-name = "VDDQ_M1_LDO_1.2V_AP";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo15_reg: LDO15 {
>> + regulator-name = "VDDQ_M2_LDO_1.2V_AP";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo16_reg: LDO16 {
>> + regulator-name = "VDDQ_EFUSE";
>> + regulator-min-microvolt = <1400000>;
>> + regulator-max-microvolt = <3400000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo17_reg: LDO17 {
>> + regulator-name = "V_TFLASH_2.8V_AP";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + };
>> +
>> + ldo18_reg: LDO18 {
>> + regulator-name = "V_CODEC_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo19_reg: LDO19 {
>> + regulator-name = "VDDA_1.8V_COMP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo20_reg: LDO20 {
>> + regulator-name = "VCC_2.8V_AP";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo21_reg: LDO21 {
>> + regulator-name = "VT_CAM_1.8V";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + ldo22_reg: LDO22 {
>> + regulator-name = "CAM_IO_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + ldo23_reg: LDO23 {
>> + regulator-name = "CAM_SEN_CORE_1.2V_AP";
>> + regulator-min-microvolt = <1050000>;
>> + regulator-max-microvolt = <1200000>;
>> + };
>> +
>> + ldo24_reg: LDO24 {
>> + regulator-name = "VT_CAM_1.2V";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + };
>> +
>> + ldo25_reg: LDO25 {
>> + regulator-name = "CAM_SEN_A2.8V_AP";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + };
>> +
>> + ldo26_reg: LDO26 {
>> + regulator-name = "CAM_AF_2.8V_AP";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + };
>> +
>> + ldo27_reg: LDO27 {
>> + regulator-name = "VCC_3.0V_LCD_AP";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo28_reg: LDO28 {
>> + regulator-name = "VCC_1.8V_LCD_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo29_reg: LDO29 {
>> + regulator-name = "VT_CAM_2.8V";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo30_reg: LDO30 {
>> + regulator-name = "TSP_AVDD_3.3V_AP";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + };
>> +
>> + ldo31_reg: LDO31 {
>> + regulator-name = "TSP_VDD_1.85V_AP";
>> + regulator-min-microvolt = <1850000>;
>> + regulator-max-microvolt = <1850000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo32_reg: LDO32 {
>> + regulator-name = "VTOUCH_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-boot-on;
>> + };
>> +
>> + ldo33_reg: LDO33 {
>> + regulator-name = "VTOUCH_LED_3.3V";
>> + regulator-min-microvolt = <2500000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-ramp-delay = <12500>;
>> + };
>> +
>> + ldo34_reg: LDO34 {
>> + regulator-name = "VCC_1.8V_MHL_AP";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <2100000>;
>> + };
>> +
>> + ldo35_reg: LDO35 {
>> + regulator-name = "OIS_VM_2.8V";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <2800000>;
>> + };
>> +
>> + ldo36_reg: LDO36 {
>> + regulator-name = "VSIL_1.0V";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + };
>> +
>> + ldo37_reg: LDO37 {
>> + regulator-name = "VF_1.8V";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>> +
>> + ldo38_reg: LDO38 {
>> + regulator-name = "VCC_3.0V_MOTOR_AP";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + };
>> +
>> + ldo39_reg: LDO39 {
>> + regulator-name = "V_HRM_1.8V";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + };
>> +
>> + ldo40_reg: LDO40 {
>> + regulator-name = "V_HRM_3.3V";
>> + regulator-min-microvolt = <3300000>;
>> + regulator-max-microvolt = <3300000>;
>> + };
>> +
>> + buck1_reg: BUCK1 {
>> + regulator-name = "VDD_MIF_0.9V_AP";
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <1500000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck2_reg: BUCK2 {
>> + regulator-name = "VDD_EGL_1.0V_AP";
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck3_reg: BUCK3 {
>> + regulator-name = "VDD_KFC_1.0V_AP";
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck4_reg: BUCK4 {
>> + regulator-name = "VDD_INT_0.95V_AP";
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <1500000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck5_reg: BUCK5 {
>> + regulator-name = "VDD_DISP_CAM0_0.9V_AP";
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <1500000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck6_reg: BUCK6 {
>> + regulator-name = "VDD_G3D_0.9V_AP";
>> + regulator-min-microvolt = <600000>;
>> + regulator-max-microvolt = <1500000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck7_reg: BUCK7 {
>> + regulator-name = "VDD_MEM1_1.2V_AP";
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + };
>> +
>> + buck8_reg: BUCK8 {
>> + regulator-name = "VDD_LLDO_1.35V_AP";
>> + regulator-min-microvolt = <1350000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
>> + };
>> +
>> + buck9_reg: BUCK9 {
>> + regulator-name = "VDD_MLDO_2.0V_AP";
>> + regulator-min-microvolt = <1350000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-always-on;
>> + };
>> +
>> + buck10_reg: BUCK10 {
>> + regulator-name = "vdd_mem2";
>> + regulator-min-microvolt = <550000>;
>> + regulator-max-microvolt = <1500000>;
>> + regulator-always-on;
>> + };
>> + };
>> + };
>> +};
>> +
>> +&hsi2c_8 {
>> + status = "okay";
>> +
>> + max77843 at 66 {
>> + compatible = "samsung,max77843";
>> + interrupt-parent = <&gpa1>;
>> + interrupts = <5 2>;
>> + reg = <0x66>;
>> + wakeup;
>
> Use common binding.
I'll remove it.
>
>> +
>> + muic: max77843-muic {
>> + compatible = "maxim,max77843-muic";
>> + };
>
>
>
Regards,
Chanwoo Choi
More information about the linux-arm-kernel
mailing list