[RESEND v2 10/10] gpio: stmpe: Add STMPE1600 support

[Lee Jones]

On Wed, 10 Aug 2016, patrice.chotard at st.com wrote:

> From: Patrice Chotard <patrice.chotard at st.com>
> 
> The particularities of this variant are:
> - GPIO_XXX_LSB and GPIO_XXX_MSB memory locations are inverted compared
>   to other variants.
> - There is no Edge detection, Rising Edge and Falling Edge registers.
> - IRQ flags are cleared when read, no need to write in Status register.
> 
> Signed-off-by: Amelie DELAUNAY <amelie.delaunay at st.com>
> Signed-off-by: Patrice Chotard <patrice.chotard at st.com>
> Reviewed-by: Linus Walleij <linus.walleij at linaro.org>
> ---
>  drivers/gpio/gpio-stmpe.c | 48 +++++++++++++++++++++++++++++++++++++----------
>  1 file changed, 38 insertions(+), 10 deletions(-)

Applied, thanks.

> diff --git a/drivers/gpio/gpio-stmpe.c b/drivers/gpio/gpio-stmpe.c
> index 6d6d76a..32c5a72 100644
> --- a/drivers/gpio/gpio-stmpe.c
> +++ b/drivers/gpio/gpio-stmpe.c
> @@ -128,8 +128,9 @@ static int stmpe_gpio_irq_set_type(struct irq_data *d, unsigned int type)
>  	if (type & IRQ_TYPE_LEVEL_LOW || type & IRQ_TYPE_LEVEL_HIGH)
>  		return -EINVAL;
>  
> -	/* STMPE801 doesn't have RE and FE registers */
> -	if (stmpe_gpio->stmpe->partnum == STMPE801)
> +	/* STMPE801 and STMPE 1600 don't have RE and FE registers */
> +	if (stmpe_gpio->stmpe->partnum == STMPE801 ||
> +	    stmpe_gpio->stmpe->partnum == STMPE1600)
>  		return 0;
>  
>  	if (type & IRQ_TYPE_EDGE_RISING)
> @@ -173,9 +174,10 @@ static void stmpe_gpio_irq_sync_unlock(struct irq_data *d)
>  	int i, j;
>  
>  	for (i = 0; i < CACHE_NR_REGS; i++) {
> -		/* STMPE801 doesn't have RE and FE registers */
> -		if ((stmpe->partnum == STMPE801) &&
> -				(i != REG_IE))
> +		/* STMPE801 and STMPE1600 don't have RE and FE registers */
> +		if ((stmpe->partnum == STMPE801 ||
> +		     stmpe->partnum == STMPE1600) &&
> +		     (i != REG_IE))
>  			continue;
>  
>  		for (j = 0; j < num_banks; j++) {
> @@ -208,11 +210,21 @@ static void stmpe_gpio_irq_unmask(struct irq_data *d)
>  {
>  	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
>  	struct stmpe_gpio *stmpe_gpio = gpiochip_get_data(gc);
> +	struct stmpe *stmpe = stmpe_gpio->stmpe;
>  	int offset = d->hwirq;
>  	int regoffset = offset / 8;
>  	int mask = 1 << (offset % 8);
>  
>  	stmpe_gpio->regs[REG_IE][regoffset] |= mask;
> +
> +	/*
> +	 * STMPE1600 workaround: to be able to get IRQ from pins,
> +	 * a read must be done on GPMR register, or a write in
> +	 * GPSR or GPCR registers
> +	 */
> +	if (stmpe->partnum == STMPE1600)
> +		stmpe_reg_read(stmpe,
> +			       stmpe->regs[STMPE_IDX_GPMR_LSB + regoffset]);
>  }
>  
>  static void stmpe_dbg_show_one(struct seq_file *s,
> @@ -285,6 +297,7 @@ static void stmpe_dbg_show_one(struct seq_file *s,
>  			fall = !!(ret & mask);
>  
>  		case STMPE801:
> +		case STMPE1600:
>  			irqen_reg = stmpe->regs[STMPE_IDX_IEGPIOR_LSB + bank];
>  			break;
>  
> @@ -331,18 +344,32 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
>  {
>  	struct stmpe_gpio *stmpe_gpio = dev;
>  	struct stmpe *stmpe = stmpe_gpio->stmpe;
> -	u8 statmsbreg = stmpe->regs[STMPE_IDX_ISGPIOR_MSB];
> +	u8 statmsbreg;
>  	int num_banks = DIV_ROUND_UP(stmpe->num_gpios, 8);
>  	u8 status[num_banks];
>  	int ret;
>  	int i;
>  
> +	/*
> +	 * the stmpe_block_read() call below, imposes to set statmsbreg
> +	 * with the register located at the lowest address. As STMPE1600
> +	 * variant is the only one which respect registers address's order
> +	 * (LSB regs located at lowest address than MSB ones) whereas all
> +	 * the others have a registers layout with MSB located before the
> +	 * LSB regs.
> +	 */
> +	if (stmpe->partnum == STMPE1600)
> +		statmsbreg = stmpe->regs[STMPE_IDX_ISGPIOR_LSB];
> +	else
> +		statmsbreg = stmpe->regs[STMPE_IDX_ISGPIOR_MSB];
> +
>  	ret = stmpe_block_read(stmpe, statmsbreg, num_banks, status);
>  	if (ret < 0)
>  		return IRQ_NONE;
>  
>  	for (i = 0; i < num_banks; i++) {
> -		int bank = num_banks - i - 1;
> +		int bank = (stmpe_gpio->stmpe->partnum == STMPE1600) ? i :
> +			   num_banks - i - 1;
>  		unsigned int enabled = stmpe_gpio->regs[REG_IE][bank];
>  		unsigned int stat = status[i];
>  
> @@ -362,10 +389,11 @@ static irqreturn_t stmpe_gpio_irq(int irq, void *dev)
>  
>  		/*
>  		 * interrupt status register write has no effect on
> -		 * 801 and 1801, bits are cleared when read.
> -		 * Edge detect register is not present on 801 and 1801
> +		 * 801/1801/1600, bits are cleared when read.
> +		 * Edge detect register is not present on 801/1600/1801
>  		 */
> -		if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1801) {
> +		if (stmpe->partnum != STMPE801 || stmpe->partnum != STMPE1600 ||
> +		    stmpe->partnum != STMPE1801) {
>  			stmpe_reg_write(stmpe, statmsbreg + i, status[i]);
>  			stmpe_reg_write(stmpe,
>  					stmpe->regs[STMPE_IDX_GPEDR_LSB + i],

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog