[RESEND v2 05/10] mfd: stmpe: use generic bit mask name

[patrice.chotard at st.com]

From: Patrice Chotard <patrice.chotard at st.com>

In order to prepare the ground to STMPE1600,
as STMPE1600's SYS_CTRL register has the same layout as
STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI
bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI

Signed-off-by: Patrice Chotard <patrice.chotard at st.com>
Acked-by: Lee Jones <lee.jones at linaro.org>
---
 drivers/mfd/stmpe.c | 4 ++--
 drivers/mfd/stmpe.h | 6 ++----
 2 files changed, 4 insertions(+), 6 deletions(-)

diff --git a/drivers/mfd/stmpe.c b/drivers/mfd/stmpe.c
index af682d0..2556463 100644
--- a/drivers/mfd/stmpe.c
+++ b/drivers/mfd/stmpe.c
@@ -1089,7 +1089,7 @@ static int stmpe_chip_init(struct stmpe *stmpe)
 
 	if (stmpe->irq >= 0) {
 		if (id == STMPE801_ID)
-			icr = STMPE801_REG_SYS_CTRL_INT_EN;
+			icr = STMPE_SYS_CTRL_INT_EN;
 		else
 			icr = STMPE_ICR_LSB_GIM;
 
@@ -1103,7 +1103,7 @@ static int stmpe_chip_init(struct stmpe *stmpe)
 		if (irq_trigger == IRQF_TRIGGER_RISING ||
 				irq_trigger == IRQF_TRIGGER_HIGH) {
 			if (id == STMPE801_ID)
-				icr |= STMPE801_REG_SYS_CTRL_INT_HI;
+				icr |= STMPE_SYS_CTRL_INT_HI;
 			else
 				icr |= STMPE_ICR_LSB_HIGH;
 		}
diff --git a/drivers/mfd/stmpe.h b/drivers/mfd/stmpe.h
index 4ae343d..4ba1123 100644
--- a/drivers/mfd/stmpe.h
+++ b/drivers/mfd/stmpe.h
@@ -105,6 +105,8 @@ int stmpe_remove(struct stmpe *stmpe);
 #define STMPE_ICR_LSB_GIM	(1 << 0)
 
 #define STMPE_SYS_CTRL_RESET	(1 << 7)
+#define STMPE_SYS_CTRL_INT_EN	(1 << 2)
+#define STMPE_SYS_CTRL_INT_HI	(1 << 0)
 
 /*
  * STMPE801
@@ -121,10 +123,6 @@ int stmpe_remove(struct stmpe *stmpe);
 #define STMPE801_REG_GPIO_SET_PIN	0x11
 #define STMPE801_REG_GPIO_DIR		0x12
 
-#define STMPE801_REG_SYS_CTRL_RESET	(1 << 7)
-#define STMPE801_REG_SYS_CTRL_INT_EN	(1 << 2)
-#define STMPE801_REG_SYS_CTRL_INT_HI	(1 << 0)
-
 /*
  * STMPE811
  */
-- 
1.9.1