[RFT PATCH 0/3] usb: misc: usb3503: Fix missing device when TFTP booting

[Hans Verkuil]

Hi Krzysztof,

On 04/29/2016 12:59 PM, Krzysztof Kozlowski wrote:
> Hi,
> 
> Patches are independent, please pick up as you wish.
> 
> However all of them are needed to solve the issue, so I am sending
> everything together for easier testng.
> 
> 
> Problem
> =======
> When Odroid U3 (usb3503 + smsc95xx + max77686) boots from network (TFTP),
> the usb3503 does not show up in "lsusb". Hard-reset is required, e.g.
> by suspend to RAM. The actual TFTP boot does not have to happen. Just
> "usb start" from U-Boot is sufficient.
> 
> 
> Solution
> ========
> Perform real hardware reset (including regulator off/on) when probing.
> 
> 
> Tested on Odroid U3 so far. Please kindly test on X2 and other
> configurations and bootloaders.

Against which kernel git repo is this patch?

I did apply this patch series first:

http://www.spinics.net/lists/arm-kernel/msg500764.html

followed by this patch series.

I've tested with both 4.6.0-rc2 and -rc5, but in all cases (even without
applying these patches!) the boot sequence hangs here:

...
[drm] Exynos DRM: using 12c10000.mixer device for DMA mapping operations
exynos-drm exynos-drm: bound 12c10000.mixer (ops mixer_component_ops)
exynos-drm exynos-drm: bound 12d00000.hdmi (ops hdmi_component_ops)
[drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[drm] No driver support for vblank timestamp query.
Console: switching to colour frame buffer device 240x67
exynos-drm exynos-drm: fb0:  frame buffer device
[drm] Initialized exynos 1.0.0 20110530 on minor 0
brd: module loaded
loop: module loaded
s3c64xx-spi 13930000.spi: spi bus clock parent not specified, using clock
at index 0 as parent
s3c64xx-spi 13930000.spi: number of chip select lines not specified,
assuming 1 chip select line
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk at qualcomm.com>
usbcore: registered new interface driver asix
usbcore: registered new interface driver ax88179_178a
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver smsc95xx
usbcore: registered new interface driver cdc_ncm
dwc2 12480000.hsotg: Specified GNPTXFDEP=1024 > 768
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci-exynos: EHCI EXYNOS driver
exynos-ehci 12580000.ehci: EHCI Host Controller
exynos-ehci 12580000.ehci: new USB bus registered, assigned bus number 1
exynos-ehci 12580000.ehci: irq 51, io mem 0x12580000
exynos-ehci 12580000.ehci: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 4.6.0-rc5-odroid ehci_hcd
usb usb1: SerialNumber: 12580000.ehci
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci-exynos: OHCI EXYNOS driver
usbcore: registered new interface driver usb-storage
usb3503 0-0008: switched to HUB mode
usb3503 0-0008: usb3503_probe: probed in hub mode
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 66:79:ef:11:72:85
usb0: MAC 1e:66:f2:66:8e:2a
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
dwc2 12480000.hsotg: bound driver g_ether
mousedev: PS/2 mouse device common for all mice
max77686-rtc max77686-rtc: rtc core: registered max77686-rtc as rtc0
i2c /dev entries driver
s5p-fimc-md camera: Entity type for entity FIMC.0 was not initialized!
usb 1-2: new high-speed USB device number 2 using exynos-ehci
usb 1-2: New USB device found, idVendor=0424, idProduct=9730
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
smsc95xx v1.0.4
smsc95xx 1-2:1.0 eth0: register 'smsc95xx' at usb-12580000.ehci-2, smsc95xx
USB 2.0 Ethernet, c2:22:09:f2:5f:e8
usb 1-3: new high-speed USB device number 3 using exynos-ehci
usb 1-3: New USB device found, idVendor=0424, idProduct=3503
usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-3:1.0: USB hub found
hub 1-3:1.0: 3 ports detected

No oops, no nothing. It's just sitting there.

Is this a regression that was introduced in 4.6? Or is there some special
new config that needs to be turned on first in 4.6? I've been running
4.5.0-rc3 before this, but I can't apply these patches there because there
is no drivers/regulator/max77686-regulator.c in 4.5.

Regards,

	Hans

> 
> 
> Best regards,
> Krzysztof
> 
> Krzysztof Kozlowski (3):
>   usb: misc: usb3503: Fix HUB mode after bootloader initialization
>   ARM: dts: exynos: Provide regulator for usb3503 on Odroid to fix
>     device detection
>   regulator: max77686: Configure enable time to properly handle
>     regulator enable
> 
>  Documentation/devicetree/bindings/usb/usb3503.txt |  1 +
>  arch/arm/boot/dts/exynos4412-odroidu3.dts         |  2 +
>  drivers/regulator/max77686-regulator.c            |  5 ++
>  drivers/usb/misc/usb3503.c                        | 81 +++++++++++++++++++++++
>  4 files changed, 89 insertions(+)
>