[pre-rfc] focus and flash for Nokia N900 (was Re: v4l subdevs without big device was Re: drivers/media/i2c/adp1653.c: does not show as /dev/video* or v4l-subdev*)
Pavel Machek
pavel at ucw.cz
Fri Apr 29 14:30:20 PDT 2016
Hi!
> "5. DT Bindings for flash & lens controllers
>
> There are drivers that create their MC topology using the device tree information,
> which works great for entities that transport data, but how to detect entities
> that don’t transport data such as flash devices, focusers, etc.? How can those be
> deduced using the device tree?
>
> Sensor DT node add phandle to focus controller: add generic v4l binding properties
> to reference such devices."
>
> This wasn't a problem with the original N900 since that didn't use DT AFAIK and
> these devices were loaded explicitly through board code.
>
> But now you run into the same problem that I have.
>
> The solution is that sensor devices have to provide phandles to those controller
> devices. And to do that you need to define bindings which is always the hard part.
>
> Look in Documentation/devicetree/bindings/media/video-interfaces.txt, section
> "Optional endpoint properties".
>
> Something like:
>
> controllers: an array of phandles to controller devices associated with this
> endpoint such as flash and lens controllers.
Ok, so after a big fight, I got both auto focus and flash to work on
n900. Relative to N900 camera trees recently posted.
Subdevs behave rather funny, and --sleep-forever is needed for useful
operation.
YA=/my/tui/yavta/yavta
# torch
sudo $YA --sleep-forever --set-control '0x009c0901 2' /dev/v4l-subdev11
# focus -- near
sudo $YA --sleep-forever --set-control '0x009a090a 1023' /dev/l-subdev12
Signed-off-by: Pavel Machek <pavel at ucw.cz>
diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts
index 9c9c1e8..acf1457 100644
--- a/arch/arm/boot/dts/omap3-n900.dts
+++ b/arch/arm/boot/dts/omap3-n900.dts
@@ -239,6 +239,7 @@
pinctrl-names = "default";
pinctrl-0 = <&camera_pins>;
+ ti,camera-flashes = <&adp1653 &cam1 &ad5820 &cam1>;
ports {
port at 1 {
@@ -251,7 +252,7 @@
data-lanes = <1>;
lane-polarity = <0 0>;
clock-inv = <0>;
- strobe = <0>;
+ strobe = <1>;
crc = <0>;
};
};
@@ -879,6 +880,16 @@
};
};
};
+
+ /* D/A converter for auto-focus */
+ ad5820: dac at 0c {
+ compatible = "adi,ad5820";
+ reg = <0x0c>;
+
+ VANA-supply = <&vaux4>;
+
+ #io-channel-cells = <0>;
+ };
};
&mmc1 {
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 254c106..77313a1 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -279,6 +279,13 @@ config VIDEO_ML86V7667
To compile this driver as a module, choose M here: the
module will be called ml86v7667.
+config VIDEO_AD5820
+ tristate "AD5820 lens voice coil support"
+ depends on I2C && VIDEO_V4L2 && MEDIA_CONTROLLER
+ ---help---
+ This is a driver for the AD5820 camera lens voice coil.
+ It is used for example in Nokia N900 (RX-51).
+
config VIDEO_SAA7110
tristate "Philips SAA7110 video decoder"
depends on VIDEO_V4L2 && I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 05e79aa..34434ae 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_VIDEO_SAA717X) += saa717x.o
obj-$(CONFIG_VIDEO_SAA7127) += saa7127.o
obj-$(CONFIG_VIDEO_SAA7185) += saa7185.o
obj-$(CONFIG_VIDEO_SAA6752HS) += saa6752hs.o
+obj-$(CONFIG_VIDEO_AD5820) += ad5820.o
obj-$(CONFIG_VIDEO_ADV7170) += adv7170.o
obj-$(CONFIG_VIDEO_ADV7175) += adv7175.o
obj-$(CONFIG_VIDEO_ADV7180) += adv7180.o
diff --git a/drivers/media/i2c/ad5820.c b/drivers/media/i2c/ad5820.c
new file mode 100644
index 0000000..5aee185
--- /dev/null
+++ b/drivers/media/i2c/ad5820.c
@@ -0,0 +1,526 @@
+/*
+ * drivers/media/i2c/ad5820.c
+ *
+ * AD5820 DAC driver for camera voice coil focus.
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Copyright (C) 2007 Texas Instruments
+ *
+ * Contact: Tuukka Toivonen <tuukka.o.toivonen at nokia.com>
+ * Sakari Ailus <sakari.ailus at nokia.com>
+ *
+ * Based on af_d88.c by Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+
+#include <linux/module.h>
+#include <linux/errno.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/sched.h>
+#include <linux/delay.h>
+#include <linux/bitops.h>
+#include <linux/kernel.h>
+#include <linux/regulator/consumer.h>
+
+#include <media/ad5820.h>
+#include <media/v4l2-device.h>
+
+#define CODE_TO_RAMP_US(s) ((s) == 0 ? 0 : (1 << ((s) - 1)) * 50)
+#define RAMP_US_TO_CODE(c) fls(((c) + ((c)>>1)) / 50)
+
+/**
+ * @brief I2C write using i2c_transfer().
+ * @param coil - the driver data structure
+ * @param data - register value to be written
+ * @returns nonnegative on success, negative if failed
+ */
+static int ad5820_write(struct ad5820_device *coil, u16 data)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&coil->subdev);
+ struct i2c_msg msg;
+ int r;
+
+ if (!client->adapter)
+ return -ENODEV;
+
+ data = cpu_to_be16(data);
+ msg.addr = client->addr;
+ msg.flags = 0;
+ msg.len = 2;
+ msg.buf = (u8 *)&data;
+
+ r = i2c_transfer(client->adapter, &msg, 1);
+ if (r < 0) {
+ dev_err(&client->dev, "write failed, error %d\n", r);
+ return r;
+ }
+
+ return 0;
+}
+
+/**
+ * @brief I2C read using i2c_transfer().
+ * @param coil - the driver data structure
+ * @returns unsigned 16-bit register value on success, negative if failed
+ */
+static int ad5820_read(struct ad5820_device *coil)
+{
+ struct i2c_client *client = v4l2_get_subdevdata(&coil->subdev);
+ struct i2c_msg msg;
+ int r;
+ u16 data = 0;
+
+ if (!client->adapter)
+ return -ENODEV;
+
+ msg.addr = client->addr;
+ msg.flags = I2C_M_RD;
+ msg.len = 2;
+ msg.buf = (u8 *)&data;
+
+ r = i2c_transfer(client->adapter, &msg, 1);
+ if (r < 0) {
+ dev_err(&client->dev, "read failed, error %d\n", r);
+ return r;
+ }
+
+ return be16_to_cpu(data);
+}
+
+/*
+ * Calculate status word and write it to the device based on current
+ * values of V4L2 controls. It is assumed that the stored V4L2 control
+ * values are properly limited and rounded.
+ */
+static int ad5820_update_hw(struct ad5820_device *coil)
+{
+ u16 status;
+
+ status = RAMP_US_TO_CODE(coil->focus_ramp_time);
+ status |= coil->focus_ramp_mode
+ ? AD5820_RAMP_MODE_64_16 : AD5820_RAMP_MODE_LINEAR;
+ status |= coil->focus_absolute << AD5820_DAC_SHIFT;
+
+ if (coil->standby)
+ status |= AD5820_POWER_DOWN;
+
+ return ad5820_write(coil, status);
+}
+
+/*
+ * Power handling
+ */
+static int ad5820_power_off(struct ad5820_device *coil, int standby)
+{
+ int ret = 0;
+
+ /*
+ * Go to standby first as real power off my be denied by the hardware
+ * (single power line control for both coil and sensor).
+ */
+ if (standby) {
+ coil->standby = 1;
+ ret = ad5820_update_hw(coil);
+ }
+
+// ret |= coil->platform_data->set_xshutdown(&coil->subdev, 0);
+ ret |= regulator_disable(coil->vana);
+
+ return ret;
+}
+
+static int ad5820_power_on(struct ad5820_device *coil, int restore)
+{
+ int ret;
+
+ printk("ad5820_power_on: 1\n");
+ ret = regulator_enable(coil->vana);
+ if (ret < 0)
+ return ret;
+
+ printk("ad5820_power_on: 2\n");
+#if 0
+ printk("ad5820_power_on: pd %lx\n", coil->platform_data);
+ printk("ad5820_power_on: xs %lx\n", coil->platform_data->set_xshutdown);
+ ret = coil->platform_data->set_xshutdown(&coil->subdev, 1);
+ if (ret)
+ goto fail;
+#endif
+
+ printk("ad5820_power_on: 3\n");
+ if (restore) {
+ /* Restore the hardware settings. */
+ coil->standby = 0;
+ printk("ad5820_power_on: 4\n");
+ ret = ad5820_update_hw(coil);
+ if (ret)
+ goto fail;
+ }
+ printk("ad5820_power_on: 5\n");
+ return 0;
+
+fail:
+ coil->standby = 1;
+
+#if 0
+ coil->platform_data->set_xshutdown(&coil->subdev, 0);
+#endif
+ regulator_disable(coil->vana);
+
+ return ret;
+}
+
+/*
+ * V4L2 controls
+ */
+static int ad5820_set_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct ad5820_device *coil =
+ container_of(ctrl->handler, struct ad5820_device, ctrls);
+ u32 code;
+ int r = 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_FOCUS_ABSOLUTE:
+ coil->focus_absolute = ctrl->val;
+ return ad5820_update_hw(coil);
+
+ case V4L2_CID_FOCUS_AD5820_RAMP_TIME:
+ code = RAMP_US_TO_CODE(ctrl->val);
+ ctrl->val = CODE_TO_RAMP_US(code);
+ coil->focus_ramp_time = ctrl->val;
+ break;
+
+ case V4L2_CID_FOCUS_AD5820_RAMP_MODE:
+ coil->focus_ramp_mode = ctrl->val;
+ break;
+ }
+
+ return r;
+}
+
+static const struct v4l2_ctrl_ops ad5820_ctrl_ops = {
+ .s_ctrl = ad5820_set_ctrl,
+};
+
+static const char *ad5820_focus_menu[] = {
+ "Linear ramp",
+ "64/16 ramp",
+};
+
+static const struct v4l2_ctrl_config ad5820_ctrls[] = {
+ {
+ .ops = &ad5820_ctrl_ops,
+ .id = V4L2_CID_FOCUS_AD5820_RAMP_TIME,
+ .type = V4L2_CTRL_TYPE_INTEGER,
+ .name = "Focus ramping time [us]",
+ .min = 0,
+ .max = 3200,
+ .step = 50,
+ .def = 0,
+ .flags = 0,
+ },
+ {
+ .ops = &ad5820_ctrl_ops,
+ .id = V4L2_CID_FOCUS_AD5820_RAMP_MODE,
+ .type = V4L2_CTRL_TYPE_MENU,
+ .name = "Focus ramping mode",
+ .min = 0,
+ .max = ARRAY_SIZE(ad5820_focus_menu),
+ .step = 0,
+ .def = 0,
+ .flags = 0,
+ .qmenu = ad5820_focus_menu,
+ },
+};
+
+
+static int ad5820_init_controls(struct ad5820_device *coil)
+{
+ unsigned int i;
+
+ v4l2_ctrl_handler_init(&coil->ctrls, ARRAY_SIZE(ad5820_ctrls) + 1);
+
+ /*
+ * V4L2_CID_FOCUS_ABSOLUTE
+ *
+ * Minimum current is 0 mA, maximum is 100 mA. Thus, 1 code is
+ * equivalent to 100/1023 = 0.0978 mA. Nevertheless, we do not use [mA]
+ * for focus position, because it is meaningless for user. Meaningful
+ * would be to use focus distance or even its inverse, but since the
+ * driver doesn't have sufficiently knowledge to do the conversion, we
+ * will just use abstract codes here. In any case, smaller value = focus
+ * position farther from camera. The default zero value means focus at
+ * infinity, and also least current consumption.
+ */
+ v4l2_ctrl_new_std(&coil->ctrls, &ad5820_ctrl_ops,
+ V4L2_CID_FOCUS_ABSOLUTE, 0, 1023, 1, 0);
+
+ /* V4L2_CID_TEST_PATTERN and V4L2_CID_MODE_* */
+ for (i = 0; i < ARRAY_SIZE(ad5820_ctrls); ++i)
+ v4l2_ctrl_new_custom(&coil->ctrls, &ad5820_ctrls[i], NULL);
+
+ if (coil->ctrls.error)
+ return coil->ctrls.error;
+
+ coil->focus_absolute = 0;
+ coil->focus_ramp_time = 0;
+ coil->focus_ramp_mode = 0;
+
+ coil->subdev.ctrl_handler = &coil->ctrls;
+ return 0;
+}
+
+/*
+ * V4L2 subdev operations
+ */
+static int
+ad5820_registered(struct v4l2_subdev *subdev)
+{
+ static const int CHECK_VALUE = 0x3FF0;
+
+ struct ad5820_device *coil = to_ad5820_device(subdev);
+ struct i2c_client *client = v4l2_get_subdevdata(subdev);
+ u16 status = AD5820_POWER_DOWN | CHECK_VALUE;
+ int rval;
+
+ printk("registered\n");
+ coil->vana = regulator_get(&client->dev, "VANA");
+ if (IS_ERR(coil->vana)) {
+ dev_err(&client->dev, "could not get regulator for vana\n");
+ return -ENODEV;
+ }
+#if 0
+ printk("detect\n");
+ /* Detect that the chip is there */
+ rval = ad5820_power_on(coil, 0);
+ if (rval)
+ goto not_detected;
+ rval = ad5820_write(coil, status);
+ if (rval)
+ goto not_detected;
+ rval = ad5820_read(coil);
+ if (rval != status)
+ goto not_detected;
+
+
+ {
+ int i, j;
+ for (j = 0; j<5; j++) {
+ printk("hwtest: phase %d\n", j);
+ for (i=0; i<1023; i++) {
+ coil->focus_absolute = i;
+ msleep(1);
+ ad5820_update_hw(coil);
+ }
+ }
+ }
+
+ printk("detect ok, poweroff\n");
+ ad5820_power_off(coil, 1);
+#endif
+ printk("controls\n");
+ return ad5820_init_controls(coil);
+
+not_detected:
+ dev_err(&client->dev, "not detected\n");
+ ad5820_power_off(coil, 0);
+ regulator_put(coil->vana);
+ return -ENODEV;
+}
+
+static int
+ad5820_set_power(struct v4l2_subdev *subdev, int on)
+{
+ struct ad5820_device *coil = to_ad5820_device(subdev);
+ int ret = 0;
+
+ mutex_lock(&coil->power_lock);
+
+ /*
+ * If the power count is modified from 0 to != 0 or from != 0 to 0,
+ * update the power state.
+ */
+ if (coil->power_count == !on) {
+ ret = on ? ad5820_power_on(coil, 1) : ad5820_power_off(coil, 1);
+ if (ret < 0)
+ goto done;
+ }
+
+ /* Update the power count. */
+ coil->power_count += on ? 1 : -1;
+ WARN_ON(coil->power_count < 0);
+
+done:
+ mutex_unlock(&coil->power_lock);
+ return ret;
+}
+
+static int ad5820_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+ return ad5820_set_power(sd, 1);
+}
+
+static int ad5820_close(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh)
+{
+ return ad5820_set_power(sd, 0);
+}
+
+static const struct v4l2_subdev_core_ops ad5820_core_ops = {
+ .s_power = ad5820_set_power,
+};
+
+static const struct v4l2_subdev_ops ad5820_ops = {
+ .core = &ad5820_core_ops,
+};
+
+static const struct v4l2_subdev_internal_ops ad5820_internal_ops = {
+ .registered = ad5820_registered,
+ .open = ad5820_open,
+ .close = ad5820_close,
+};
+
+/*
+ * I2C driver
+ */
+#ifdef CONFIG_PM
+
+static int ad5820_suspend(struct device *dev)
+{
+ struct i2c_client *client = container_of(dev, struct i2c_client, dev);
+ struct v4l2_subdev *subdev = i2c_get_clientdata(client);
+ struct ad5820_device *coil = to_ad5820_device(subdev);
+
+ if (!coil->power_count)
+ return 0;
+
+ return ad5820_power_off(coil, 0);
+}
+
+static int ad5820_resume(struct device *dev)
+{
+ struct i2c_client *client = container_of(dev, struct i2c_client, dev);
+ struct v4l2_subdev *subdev = i2c_get_clientdata(client);
+ struct ad5820_device *coil = to_ad5820_device(subdev);
+
+ if (!coil->power_count)
+ return 0;
+
+ return ad5820_power_on(coil, 1);
+}
+
+#else
+
+#define ad5820_suspend NULL
+#define ad5820_resume NULL
+
+#endif /* CONFIG_PM */
+
+static int ad5820_probe(struct i2c_client *client,
+ const struct i2c_device_id *devid)
+{
+ struct ad5820_device *coil;
+ int ret = 0;
+
+ coil = kzalloc(sizeof(*coil), GFP_KERNEL);
+ if (coil == NULL)
+ return -ENOMEM;
+
+ coil->platform_data = NULL; // client->dev.platform_data;
+
+ mutex_init(&coil->power_lock);
+
+ v4l2_i2c_subdev_init(&coil->subdev, client, &ad5820_ops);
+ coil->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ coil->subdev.internal_ops = &ad5820_internal_ops;
+ strcpy(coil->subdev.name, "ad5820 focus");
+
+ ret = media_entity_pads_init(&coil->subdev.entity, 0, NULL);
+ if (ret < 0) {
+ kfree(coil);
+ return ret;
+ }
+
+ ret = v4l2_async_register_subdev(&coil->subdev);
+ if (ret < 0)
+ kfree(coil);
+
+ printk("Hack -- testing hw\n");
+ ad5820_registered(coil);
+
+ printk("hw test done\n");
+
+ return ret;
+}
+
+static int __exit ad5820_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *subdev = i2c_get_clientdata(client);
+ struct ad5820_device *coil = to_ad5820_device(subdev);
+
+ v4l2_device_unregister_subdev(&coil->subdev);
+ v4l2_ctrl_handler_free(&coil->ctrls);
+ media_entity_cleanup(&coil->subdev.entity);
+ if (coil->vana)
+ regulator_put(coil->vana);
+
+ kfree(coil);
+ return 0;
+}
+
+static const struct i2c_device_id ad5820_id_table[] = {
+ { AD5820_NAME, 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, ad5820_id_table);
+
+static SIMPLE_DEV_PM_OPS(ad5820_pm, ad5820_suspend, ad5820_resume);
+
+static struct i2c_driver ad5820_i2c_driver = {
+ .driver = {
+ .name = AD5820_NAME,
+ .pm = &ad5820_pm,
+ },
+ .probe = ad5820_probe,
+ .remove = __exit_p(ad5820_remove),
+ .id_table = ad5820_id_table,
+};
+
+static int __init ad5820_init(void)
+{
+ int rval;
+
+ rval = i2c_add_driver(&ad5820_i2c_driver);
+ if (rval)
+ printk(KERN_INFO "%s: failed registering " AD5820_NAME "\n",
+ __func__);
+
+ return rval;
+}
+
+static void __exit ad5820_exit(void)
+{
+ i2c_del_driver(&ad5820_i2c_driver);
+}
+
+
+module_init(ad5820_init);
+module_exit(ad5820_exit);
+
+MODULE_AUTHOR("Tuukka Toivonen <tuukka.o.toivonen at nokia.com>");
+MODULE_DESCRIPTION("AD5820 camera lens driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/media/i2c/adp1653.c b/drivers/media/i2c/adp1653.c
index 0cd494e..6dd5d6a 100644
--- a/drivers/media/i2c/adp1653.c
+++ b/drivers/media/i2c/adp1653.c
@@ -306,6 +306,8 @@ adp1653_init_device(struct adp1653_flash *flash)
return -EIO;
}
+ dev_info(&client->dev, "adp1653 device ok\n", __func__);
+
return 0;
}
@@ -492,6 +494,8 @@ static int adp1653_probe(struct i2c_client *client,
if (flash == NULL)
return -ENOMEM;
+ dev_info(&client->dev, "adp1653 probe\n");
+
if (client->dev.of_node) {
ret = adp1653_of_init(client, flash, client->dev.of_node);
if (ret)
@@ -505,11 +509,13 @@ static int adp1653_probe(struct i2c_client *client,
flash->platform_data = client->dev.platform_data;
}
+ dev_info(&client->dev, "adp1653 probe: subdev\n", __func__);
mutex_init(&flash->power_lock);
v4l2_i2c_subdev_init(&flash->subdev, client, &adp1653_ops);
flash->subdev.internal_ops = &adp1653_internal_ops;
flash->subdev.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ strcpy(flash->subdev.name, "adp1653 flash");
ret = adp1653_init_controls(flash);
if (ret)
@@ -519,6 +525,14 @@ static int adp1653_probe(struct i2c_client *client,
if (ret < 0)
goto free_and_quit;
+ dev_info(&client->dev, "adp1653 probe: should be ok\n");
+
+ ret = v4l2_async_register_subdev(&flash->subdev);
+ if (ret < 0)
+ goto free_and_quit;
+
+ dev_info(&client->dev, "adp1653 probe: async register subdev ok\n");
+
flash->subdev.entity.function = MEDIA_ENT_F_FLASH;
return 0;
@@ -538,6 +552,8 @@ static int adp1653_remove(struct i2c_client *client)
v4l2_ctrl_handler_free(&flash->ctrls);
media_entity_cleanup(&flash->subdev.entity);
+ dev_info(&client->dev, "adp1653 remove\n");
+
return 0;
}
diff --git a/drivers/media/platform/omap3isp/isp.c b/drivers/media/platform/omap3isp/isp.c
index 6361fde..23d484c 100644
--- a/drivers/media/platform/omap3isp/isp.c
+++ b/drivers/media/platform/omap3isp/isp.c
@@ -2095,13 +2095,20 @@ static void isp_of_parse_node_csi2(struct device *dev,
buscfg->bus.csi2.crc = 1;
}
-static int isp_of_parse_node(struct device *dev, struct device_node *node,
- struct isp_async_subdev *isd)
+static int isp_of_parse_node_endpoint(struct device *dev,
+ struct device_node *node,
+ struct isp_async_subdev *isd)
{
- struct isp_bus_cfg *buscfg = &isd->bus;
+ struct isp_bus_cfg *buscfg;
struct v4l2_of_endpoint vep;
int ret;
+ isd->bus = devm_kzalloc(dev, sizeof(*isd->bus), GFP_KERNEL);
+ if (!isd->bus)
+ return -ENOMEM;
+
+ buscfg = isd->bus;
+
ret = v4l2_of_parse_endpoint(node, &vep);
if (ret)
return ret;
@@ -2144,10 +2151,51 @@ static int isp_of_parse_node(struct device *dev, struct device_node *node,
return 0;
}
+static int isp_of_parse_node(struct device *dev, struct device_node *node,
+ struct v4l2_async_notifier *notifier,
+ u32 group_id, bool link)
+{
+ struct isp_async_subdev *isd;
+
+ isd = devm_kzalloc(dev, sizeof(*isd), GFP_KERNEL);
+ if (!isd) {
+ of_node_put(node);
+ return -ENOMEM;
+ }
+
+ notifier->subdevs[notifier->num_subdevs] = &isd->asd;
+
+ if (link) {
+ if (isp_of_parse_node_endpoint(dev, node, isd)) {
+ of_node_put(node);
+ return -EINVAL;
+ }
+
+ isd->asd.match.of.node = of_graph_get_remote_port_parent(node);
+ of_node_put(node);
+ } else {
+ isd->asd.match.of.node = node;
+ }
+
+ if (!isd->asd.match.of.node) {
+ dev_warn(dev, "bad remote port parent\n");
+ return -EINVAL;
+ }
+
+ isd->asd.match_type = V4L2_ASYNC_MATCH_OF;
+ isd->group_id = group_id;
+ notifier->num_subdevs++;
+
+ return 0;
+}
+
static int isp_of_parse_nodes(struct device *dev,
struct v4l2_async_notifier *notifier)
{
struct device_node *node = NULL;
+ int ret;
+ unsigned int flash = 0;
+ u32 group_id = 0;
notifier->subdevs = devm_kcalloc(
dev, ISP_MAX_SUBDEVS, sizeof(*notifier->subdevs), GFP_KERNEL);
@@ -2156,30 +2204,57 @@ static int isp_of_parse_nodes(struct device *dev,
while (notifier->num_subdevs < ISP_MAX_SUBDEVS &&
(node = of_graph_get_next_endpoint(dev->of_node, node))) {
- struct isp_async_subdev *isd;
+ ret = isp_of_parse_node(dev, node, notifier, group_id++, true);
+ if (ret)
+ return ret;
+ }
- isd = devm_kzalloc(dev, sizeof(*isd), GFP_KERNEL);
- if (!isd) {
- of_node_put(node);
- return -ENOMEM;
- }
+ while (notifier->num_subdevs < ISP_MAX_SUBDEVS &&
+ (node = of_parse_phandle(dev->of_node, "ti,camera-flashes",
+ flash++))) {
+ struct device_node *sensor_node =
+ of_parse_phandle(dev->of_node, "ti,camera-flashes",
+ flash++);
+ unsigned int i;
+ u32 flash_group_id;
+
+ if (!sensor_node)
+ return -EINVAL;
- notifier->subdevs[notifier->num_subdevs] = &isd->asd;
+ for (i = 0; i < notifier->num_subdevs; i++) {
+ struct isp_async_subdev *isd = container_of(
+ notifier->subdevs[i], struct isp_async_subdev,
+ asd);
- if (isp_of_parse_node(dev, node, isd)) {
- of_node_put(node);
- return -EINVAL;
+ if (!isd->bus)
+ continue;
+
+ dev_dbg(dev, "match \"%s\", \"%s\"\n",sensor_node->name,
+ isd->asd.match.of.node->name);
+
+ if (sensor_node != isd->asd.match.of.node)
+ continue;
+
+ dev_dbg(dev, "found\n");
+
+ flash_group_id = isd->group_id;
+ break;
}
- isd->asd.match.of.node = of_graph_get_remote_port_parent(node);
- of_node_put(node);
- if (!isd->asd.match.of.node) {
- dev_warn(dev, "bad remote port parent\n");
- return -EINVAL;
+ /*
+ * No sensor was found --- complain and allocate a new
+ * group ID.
+ */
+ if (i == notifier->num_subdevs) {
+ dev_warn(dev, "no device node \"%s\" was found",
+ sensor_node->name);
+ flash_group_id = group_id++;
}
- isd->asd.match_type = V4L2_ASYNC_MATCH_OF;
- notifier->num_subdevs++;
+ ret = isp_of_parse_node(dev, node, notifier, flash_group_id,
+ false);
+ if (ret)
+ return ret;
}
return notifier->num_subdevs;
@@ -2192,8 +2267,9 @@ static int isp_subdev_notifier_bound(struct v4l2_async_notifier *async,
struct isp_async_subdev *isd =
container_of(asd, struct isp_async_subdev, asd);
+// subdev->entity.group_id = isd->group_id;
isd->sd = subdev;
- isd->sd->host_priv = &isd->bus;
+ isd->sd->host_priv = isd->bus;
return 0;
}
@@ -2396,12 +2472,15 @@ static int isp_probe(struct platform_device *pdev)
if (ret < 0)
goto error_register_entities;
- isp->notifier.bound = isp_subdev_notifier_bound;
- isp->notifier.complete = isp_subdev_notifier_complete;
+ if (IS_ENABLED(CONFIG_OF) && pdev->dev.of_node) {
+ isp->notifier.bound = isp_subdev_notifier_bound;
+ isp->notifier.complete = isp_subdev_notifier_complete;
- ret = v4l2_async_notifier_register(&isp->v4l2_dev, &isp->notifier);
- if (ret)
- goto error_register_entities;
+ ret = v4l2_async_notifier_register(&isp->v4l2_dev,
+ &isp->notifier);
+ if (ret)
+ goto error_register_entities;
+ }
isp_core_init(isp, 1);
omap3isp_put(isp);
diff --git a/drivers/media/platform/omap3isp/isp.h b/drivers/media/platform/omap3isp/isp.h
index 7e6f663..639b3ca 100644
--- a/drivers/media/platform/omap3isp/isp.h
+++ b/drivers/media/platform/omap3isp/isp.h
@@ -228,8 +228,9 @@ struct isp_device {
struct isp_async_subdev {
struct v4l2_subdev *sd;
- struct isp_bus_cfg bus;
+ struct isp_bus_cfg *bus;
struct v4l2_async_subdev asd;
+ u32 group_id;
};
#define v4l2_dev_to_isp_device(dev) \
diff --git a/drivers/media/platform/omap3isp/ispcsiphy.c b/drivers/media/platform/omap3isp/ispcsiphy.c
index 495447d..750ce93 100644
--- a/drivers/media/platform/omap3isp/ispcsiphy.c
+++ b/drivers/media/platform/omap3isp/ispcsiphy.c
@@ -177,7 +177,7 @@ static int omap3isp_csiphy_config(struct isp_csiphy *phy)
struct isp_async_subdev *isd =
container_of(pipe->external->asd,
struct isp_async_subdev, asd);
- buscfg = &isd->bus;
+ buscfg = isd->bus;
}
if (buscfg->interface == ISP_INTERFACE_CCP2B_PHY1
diff --git a/include/media/ad5820.h b/include/media/ad5820.h
new file mode 100644
index 0000000..f5a1565
--- /dev/null
+++ b/include/media/ad5820.h
@@ -0,0 +1,70 @@
+/*
+ * include/media/ad5820.h
+ *
+ * Copyright (C) 2008 Nokia Corporation
+ * Copyright (C) 2007 Texas Instruments
+ *
+ * Contact: Tuukka Toivonen <tuukka.o.toivonen at nokia.com>
+ * Sakari Ailus <sakari.ailus at nokia.com>
+ *
+ * Based on af_d88.c by Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful, but
+ * WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
+ * 02110-1301 USA
+ */
+
+#ifndef AD5820_H
+#define AD5820_H
+
+#include <linux/i2c.h>
+#include <linux/mutex.h>
+#include <linux/videodev2.h>
+
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-subdev.h>
+
+struct regulator;
+
+#define AD5820_NAME "ad5820"
+#define AD5820_I2C_ADDR (0x18 >> 1)
+
+/* Register definitions */
+#define AD5820_POWER_DOWN (1 << 15)
+#define AD5820_DAC_SHIFT 4
+#define AD5820_RAMP_MODE_LINEAR (0 << 3)
+#define AD5820_RAMP_MODE_64_16 (1 << 3)
+
+struct ad5820_platform_data {
+ int (*set_xshutdown)(struct v4l2_subdev *subdev, int set);
+};
+
+#define to_ad5820_device(sd) container_of(sd, struct ad5820_device, subdev)
+
+struct ad5820_device {
+ struct v4l2_subdev subdev;
+ struct ad5820_platform_data *platform_data;
+ struct regulator *vana;
+
+ struct v4l2_ctrl_handler ctrls;
+ u32 focus_absolute;
+ u32 focus_ramp_time;
+ u32 focus_ramp_mode;
+
+ struct mutex power_lock;
+ int power_count;
+
+ int standby : 1;
+};
+
+#endif /* AD5820_H */
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
More information about the linux-arm-kernel
mailing list