[PATCH 5/6] Documentation: Binding doc for ethernet master in NS2

[Pramod Kumar]

Hi Rob,

Thanks for review and providing your valuable comments.

> -----Original Message-----
> From: Rob Herring [mailto:robh at kernel.org]
> Sent: 23 April 2016 01:44
> To: Pramod Kumar
> Cc: Catalin Marinas; Will Deacon; Masahiro Yamada; Chen-Yu Tsai; BCM
Kernel
> Feedback; Pawel Moll; Mark Rutland; Arnd Bergmann; Suzuki K Poulose;
Punit
> Agrawal; devicetree at vger.kernel.org;
linux-arm-kernel at lists.infradead.org;
> linux-kernel at vger.kernel.org; netdev at vger.kernel.org
> Subject: Re: [PATCH 5/6] Documentation: Binding doc for ethernet master
in
> NS2
>
> On Thu, Apr 21, 2016 at 02:48:42PM +0530, Pramod Kumar wrote:
> > Adding binding doc for ethernet master present in shared MDIO
> > controller.
> >
> > Signed-off-by: Pramod Kumar <pramod.kumar at broadcom.com>
> > Reviewed-by: Ray Jui <ray.jui at broadcom.com>
> > Reviewed-by: Scott Branden <scott.branden at broadcom.com>
> > ---
> >  .../bindings/net/brcm,iproc-mdio-shared.txt        | 32
> ++++++++++++++++++++++
> >  1 file changed, 32 insertions(+)
> >  create mode 100644
> > Documentation/devicetree/bindings/net/brcm,iproc-mdio-shared.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/net/brcm,iproc-mdio-shared.txt
> > b/Documentation/devicetree/bindings/net/brcm,iproc-mdio-shared.txt
> > new file mode 100644
> > index 0000000..1ffdd4b
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/net/brcm,iproc-mdio-shared.txt
> > @@ -0,0 +1,32 @@
> > +Broadcom Ethernet master for shared mdio controller
> > +
> > +Required properties:
> > +- compatible: must be "brcm,iproc-mdio-master-eth"
> > +- reg: master id of Ethernet block
> > +- address-cells: should be 1
> > +- size-cells: should be 0
> > +
> > +Sub-nodes:
> > +  Each port's PHY should be represented as a sub-node.
> > +
> > +Sub-nodes required properties:
> > +- reg: the PHY number
> > +- phy-mode: media type connecting the PHY and MAC.
> > +
> > +
> > +Example:
> > +	eth-master at 0 {
>
> Is this a child of something?
>

This is an Shared MDIO master node as described in cover letter and is the
child node of iProc_shared_mdio plarform driver.


> Why is this not just an mdio bus underneath the ethernet controller? How
is this
> accessed?

This is the part for Shared MDIO controller which is shared among other
subsystem as well hence defined here. This works as glue layer between
This controller and legacy MDIO framework and register the MDIO bus to
legacy framework.
When any read/write request is issue from Legacy MDIO controller framework
it gets propagated to Shared controller platform driver via this driver
and finally platform driver issue MDIO transaction over bus.

>
> > +		compatible = "brcm,iproc-mdio-master-eth";
> > +		reg = <0x0>;
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		gphy0: eth-phy at 10 {
> > +			reg = <0x10>;
> > +			phy-mode = "mii";
> > +		};
> > +		status = "ok"
> > +	};
> > +
> > +For more info on ethernet phy binding, please,refer to:
> > +Documentation/devicetree/bindings/net/phy.txt
> > +Documentation/devicetree/bindings/net/ethernet.txt
> > --
> > 1.9.1
> >

Regards,
Pramod