[PATCH v2 0/3] ARM: OMAP3: Fix McBSP2/3 hwmod setup for sidetone

[Peter Ujfalusi]

On 04/15/2016 06:16 PM, Tony Lindgren wrote:
>> The hwmod checks the bits described by prcm.omap2. If two hwmods are set up to
>> manage/monitor the same bits in PRCM, what will happen when the two driver
>> does pm_runtime?
>>
>> CM_ICLKEN_PER[0] = 1
>> McBSP2: runtime_get_sync()
>> CM_ICLKEN_PER[0] = 0
>> ...
>> CM_ICLKEN_PER[0] = 0
>> McBSP2.ST: runtime_get_sync() // hwmod might complain as the idlest was not 1?
>> CM_ICLKEN_PER[0] = 0
>> ...
>> CM_ICLKEN_PER[0] = 0
>> McBSP2.ST: runtime_put_sync()
>> CM_ICLKEN_PER[0] = 0 // hwmod might warn that the module did not went idle?
>> ...
>> CM_ICLKEN_PER[0] = 0
>> McBSP2: runtime_put_sync()
>> CM_ICLKEN_PER[0] = 1
>>
>> We can hack this around by adding HWMOD_NO_IDLEST to the sidetone hwmod I
>> guess. As the sidetone does not have PRCM level control - it is part of McBSP.
> 
> Heh if they are using the same register bits for two separate modules,
> then that's a bug for sure :) I think the sidetone module only has the
> clock gating bit in the ST_SYSCONFIG.

Yes, the sidetone only has clock gating bit in ST_SYSCONFIG, but the hwmod has
the prcm section which is identical of the corresponding McBSP hwmod prcm section.

Since we have only one MCBSP2_ICLK and only one bit in PRCM registers for it,
this is a bug in the hwmod data for sure. Only the mcbsp hwmod should have
prcm section and the sidetone hwmod is not needed IMO:
It is a bug to have sidetone enabled when McBSP is not enabled and configured
properly. The sidetone can not work w/o proper McBSP configuration.

If we were to keep both hwmods and add new set of pm_runtime calls for the
mcbsp.sidetone, it will only increase/decrease the mcbsp_iclk enable count. It
must never enable the clock itself since that is a bug in the SW.

>>> Then there are two separate sets of sysconfig registers that PM runtime should manage.
>>
>> The sidetone core's sysconfig register is internal to McBSP module. This is
>> what the TRM has to say about McBSPi.ST_SYSCONFIG_REG[0] AUTOIDLE bit:
>> - When this bit is asserted (set to 1), the McBSPi_ICLK clock auto-gating is
>> enabled and this clock is disabled internally to the SIDETONE feature, thus
>> reducing power consumption, but not to the McBSP module that contains this
>> feature.
> 
> Some confusion here.. The McBSPi_ICLK is external, it's just shared
> between the McBSP and sidetone modules. So the ST_SYSCONFIG gates
> internally separately to the sidetone.

I think it is called McBSPi_ICLK internally also, but true. The same clock
from PRCM goes to McBSPi core and McBSPi.sidetone core. The only difference is
that the sidetone is only able to gate the clock internally.

>> After reset, the automatic clock gating is enabled; thus, this bit must be
>> disabled by software for activated SIDETONE feature.
>> - When this bit is set to 0, the McBSPi_ICLK clock auto-gating is disabled and
>> this clock is enabled. The SIDETONE feature can be used normally.
>>
>> The ST_SYSCONFIG_REG is internal to the McBSP module the ST is integrated into.
> 
> The ST_SYSCONFIG is internal to the sidetone module only. Then the
> McBSP module has it's own SYSCONFIG register that's internal to the
> McBSP module only.

And the McBSP core can signal (ack) the PRCM back, but the sidetone core can not.

> I think the confusion comes from the McBSPi_ICLK naming, that's not
> internal to the module(s) in question, it comes from an external
> shared source that the SYSCONFIG registers control.
> 
> Some SYSCONFIG registers have autoidle features that signal the
> source clockdomain too.
> 
>> I'm still not convinced about the benefits of creating separate device for the
>> ST core of McBSP.
>> From my point of view:
>> McBSP2 module consist of:
>> - McBSP core
>>  - clock generator subcore
>>  - tx subcore
>>  - rx subcore
>> - Sidetone core
> 
> I think it's more like this for the clocking and
> intermodule lines:
> 
> clockdomain
> clock generarator ---+
> subcore              |
>                      +- McBSP
>                      |  internal gating
>                      |  and signaling to
>                      |  clockdomain via
>                      |  SYSCONFIG register
>                      |        | |
>                      |        | | intermodule lines
>                      |        | | not on the interconnect
>                      |        | |
>                      +- sidetone
>                      |  internal gating
>                      |  (and signaling to
>                      |  clockdomain via
>                      |  SYSCONFIG register?)
> 
> Then all these modules just sit on the L4 interconnet at
> separate targets, including the clockdomain.

The McBSPi core and it's sidetone is in the same clock domain as the sidetone
is using the McBSPi interface clock. It is kind of a leech ;)
It is more like:

clockdomain
clock generator ---+
subcore            |
                   +--+--McBSP2
                   |  |
                   |  |
                   |  McBSP2_sidetone


-- 
Péter