[PATCH] i2c: designware-platdrv: implement bus recovery
Jisheng Zhang
jszhang at marvell.com
Thu Apr 14 23:08:43 PDT 2016
Dear Mika,
On Thu, 14 Apr 2016 17:39:16 +0300 Mika Westerberg wrote:
> On Thu, Apr 14, 2016 at 10:04:56PM +0800, Jisheng Zhang wrote:
> > Implement bus recovery methods for i2c designware so we can recover
> > from situations where SCL/SDA are stuck low.
> >
> > The recovery method is similar as i2c-imx: "config the i2c pinctrl to
> > gpio mode by calling pinctrl sleep set function, and then use GPIO to
> > emulate the i2c protocol to send nine dummy clock to recover i2c
> > device. After recovery, set i2c pinctrl to default group setting.
> >
> > Signed-off-by: Jisheng Zhang <jszhang at marvell.com>
> > ---
> > depends on runtime pm patches
> > http://lists.infradead.org/pipermail/linux-arm-kernel/2016-April/422202.html
> > .../devicetree/bindings/i2c/i2c-designware.txt | 12 ++++++
> > drivers/i2c/busses/i2c-designware-core.c | 6 ++-
> > drivers/i2c/busses/i2c-designware-core.h | 4 ++
> > drivers/i2c/busses/i2c-designware-platdrv.c | 50 ++++++++++++++++++++++
> > 4 files changed, 71 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/i2c/i2c-designware.txt b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> > index fee26dc..51a55c6 100644
> > --- a/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> > +++ b/Documentation/devicetree/bindings/i2c/i2c-designware.txt
> > @@ -20,6 +20,13 @@ Optional properties :
> > - i2c-sda-falling-time-ns : should contain the SDA falling time in nanoseconds.
> > This value which is by default 300ns is used to compute the tHIGH period.
> >
> > + - scl-gpios: specify the gpio related to SCL pin
> > +
> > + - sda-gpios: specify the gpio related to SDA pin
> > +
> > + - pinctrl: add extra pinctrl to configure i2c pins to gpio function for i2c
> > + bus recovery, call it "gpio" state
> > +
> > Example :
> >
> > i2c at f0000 {
> > @@ -42,4 +49,9 @@ Example :
> > i2c-sda-hold-time-ns = <300>;
> > i2c-sda-falling-time-ns = <300>;
> > i2c-scl-falling-time-ns = <300>;
> > + pinctrl-names = "default", "gpio";
> > + pinctrl-0 = <&pinctrl_i2c1_default>;
> > + pinctrl-1 = <&pinctrl_i2c1_gpio>;
> > + scl-gpios = <&porta 26 GPIO_ACTIVE_HIGH>;
> > + sda-gpios = <&porta 27 GPIO_ACTIVE_HIGH>;
> > };
> > diff --git a/drivers/i2c/busses/i2c-designware-core.c b/drivers/i2c/busses/i2c-designware-core.c
> > index 4255eaa..be40de1 100644
> > --- a/drivers/i2c/busses/i2c-designware-core.c
> > +++ b/drivers/i2c/busses/i2c-designware-core.c
> > @@ -399,7 +399,10 @@ static int i2c_dw_wait_bus_not_busy(struct dw_i2c_dev *dev)
> > while (dw_readl(dev, DW_IC_STATUS) & DW_IC_STATUS_ACTIVITY) {
> > if (timeout <= 0) {
> > dev_warn(dev->dev, "timeout waiting for bus ready\n");
> > - return -ETIMEDOUT;
> > + i2c_recover_bus(&dev->adapter);
> > + if (dw_readl(dev, DW_IC_STATUS)
> > + & DW_IC_STATUS_ACTIVITY)
> > + return -ETIMEDOUT;
> > }
> > timeout--;
> > usleep_range(1000, 1100);
> > @@ -665,6 +668,7 @@ i2c_dw_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num)
> > /* wait for tx to complete */
> > if (!wait_for_completion_timeout(&dev->cmd_complete, HZ)) {
> > dev_err(dev->dev, "controller timed out\n");
> > + i2c_recover_bus(&dev->adapter);
> > /* i2c_dw_init implicitly disables the adapter */
> > i2c_dw_init(dev);
> > ret = -ETIMEDOUT;
> > diff --git a/drivers/i2c/busses/i2c-designware-core.h b/drivers/i2c/busses/i2c-designware-core.h
> > index cd409e7..26c84ee 100644
> > --- a/drivers/i2c/busses/i2c-designware-core.h
> > +++ b/drivers/i2c/busses/i2c-designware-core.h
> > @@ -104,6 +104,10 @@ struct dw_i2c_dev {
> > u16 fs_lcnt;
> > int (*acquire_lock)(struct dw_i2c_dev *dev);
> > void (*release_lock)(struct dw_i2c_dev *dev);
> > + struct i2c_bus_recovery_info rinfo;
> > + struct pinctrl *pinctrl;
> > + struct pinctrl_state *pinctrl_pins_default;
> > + struct pinctrl_state *pinctrl_pins_gpio;
> > bool pm_runtime_disabled;
> > };
> >
> > diff --git a/drivers/i2c/busses/i2c-designware-platdrv.c b/drivers/i2c/busses/i2c-designware-platdrv.c
> > index 1488cea..62bded9 100644
> > --- a/drivers/i2c/busses/i2c-designware-platdrv.c
> > +++ b/drivers/i2c/busses/i2c-designware-platdrv.c
> > @@ -33,6 +33,7 @@
> > #include <linux/err.h>
> > #include <linux/interrupt.h>
> > #include <linux/of.h>
> > +#include <linux/of_gpio.h>
> > #include <linux/platform_device.h>
> > #include <linux/pm.h>
> > #include <linux/pm_runtime.h>
> > @@ -148,6 +149,49 @@ static int i2c_dw_plat_prepare_clk(struct dw_i2c_dev *i_dev, bool prepare)
> > return 0;
> > }
> >
> > +static void i2c_dw_plat_prepare_recovery(struct i2c_adapter *adap)
> > +{
> > + struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
> > +
> > + pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_gpio);
> > +}
> > +
> > +static void i2c_dw_plat_unprepare_recovery(struct i2c_adapter *adap)
> > +{
> > + struct dw_i2c_dev *dev = i2c_get_adapdata(adap);
> > +
> > + pinctrl_select_state(dev->pinctrl, dev->pinctrl_pins_default);
> > +}
> > +
> > +static void i2c_dw_plat_init_recovery_info(struct dw_i2c_dev *dev,
> > + struct platform_device *pdev)
> > +{
> > + struct i2c_bus_recovery_info *rinfo = &dev->rinfo;
> > +
> > + dev->pinctrl_pins_default = pinctrl_lookup_state(dev->pinctrl,
> > + PINCTRL_STATE_DEFAULT);
> > + dev->pinctrl_pins_gpio = pinctrl_lookup_state(dev->pinctrl,
> > + "gpio");
> > + rinfo->sda_gpio = of_get_named_gpio(pdev->dev.of_node, "sda-gpios", 0);
> > + rinfo->scl_gpio = of_get_named_gpio(pdev->dev.of_node, "scl-gpios", 0);
> > +
> > + if (!gpio_is_valid(rinfo->sda_gpio) ||
> > + !gpio_is_valid(rinfo->scl_gpio) ||
> > + IS_ERR(dev->pinctrl_pins_default) ||
> > + IS_ERR(dev->pinctrl_pins_gpio)) {
> > + dev_dbg(&pdev->dev, "recovery information incomplete\n");
> > + return;
For ACPI, we should return here, right?
> > + }
> > +
> > + dev_dbg(&pdev->dev, "using scl-gpio %d and sda-gpio %d for recovery\n",
> > + rinfo->sda_gpio, rinfo->scl_gpio);
> > +
> > + rinfo->prepare_recovery = i2c_dw_plat_prepare_recovery;
> > + rinfo->unprepare_recovery = i2c_dw_plat_unprepare_recovery;
> > + rinfo->recover_bus = i2c_generic_gpio_recovery;
>
> This whole thing is DT specific and I don't see how we can do the same
> for ACPI. Should it be enabled only when the controller was enumerated
> from DT?
Per my understanding, for ACPI, the pinctrl_pins_default, pinctrl_pins_gpio,
sda_gpio and scl_gpio will be invalid or err, so we won't setup rinfo
at all. However, I have no acpi platform which have i2c designware to double
confirm.
>
> > + dev->adapter.bus_recovery_info = rinfo;
> > +}
> > +
> > static int dw_i2c_plat_probe(struct platform_device *pdev)
> > {
> > struct dw_i2c_platform_data *pdata = dev_get_platdata(&pdev->dev);
> > @@ -165,6 +209,12 @@ static int dw_i2c_plat_probe(struct platform_device *pdev)
> > if (!dev)
> > return -ENOMEM;
> >
> > + dev->pinctrl = devm_pinctrl_get(&pdev->dev);
> > + if (IS_ERR(dev->pinctrl))
> > + return PTR_ERR(dev->pinctrl);
> > +
> > + i2c_dw_plat_init_recovery_info(dev, pdev);
> > +
> > mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > dev->base = devm_ioremap_resource(&pdev->dev, mem);
> > if (IS_ERR(dev->base))
> > --
> > 2.8.0.rc3
More information about the linux-arm-kernel
mailing list