[PATCH 01/11 RESEND] ARM: OMAP: DRA7: hwmod: Add data for McASP3

[Tero Kristo]

On 09/30/2015 01:06 PM, Peter Ujfalusi wrote:
> Paul,
>
> On 09/27/2015 10:02 AM, Paul Walmsley wrote:
>>>   /*
>>> + * 'mcasp' class
>>> + *
>>> + */
>>> +static struct omap_hwmod_class_sysconfig dra7xx_mcasp_sysc = {
>>> +	.sysc_offs	= 0x0004,
>>> +	.sysc_flags	= SYSC_HAS_SIDLEMODE,
>>> +	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
>>> +	.sysc_fields	= &omap_hwmod_sysc_type3,
>>> +};
>>> +
>>> +static struct omap_hwmod_class dra7xx_mcasp_hwmod_class = {
>>> +	.name	= "mcasp",
>>> +	.sysc	= &dra7xx_mcasp_sysc,
>>> +};
>>> +
>>> +/* mcasp3 */
>>> +static struct omap_hwmod dra7xx_mcasp3_hwmod = {
>>> +	.name		= "mcasp3",
>>> +	.class		= &dra7xx_mcasp_hwmod_class,
>>> +	.clkdm_name	= "l4per2_clkdm",
>>> +	.main_clk	= "mcasp3_ahclkx_mux",
>>
>> I'd expect this clock to be something derived from mcasp3_aux_gfclk,
>> according to Table 24-408 "Clocks and Resets" of SPRUHZ6.  Could you
>> please doublecheck this?
>
> I can not explain this. If I change the main_clk to "mcasp3_aux_gfclk_mux"
> then I can not access to McASP3 register at all.
> I don't see anything popping out in the clock data, nor in other places.
>
>>> +	.flags		= HWMOD_SWSUP_SIDLE,
>
> Not sure why this has been added, I can not find any pointers regarding to
> this and everything is working w/o this flag. Will remove it in v2.
>
>
>> Is this needed?  If it is, please add a brief comment describing the issue
>> or bug that it's working around.
>>
>>> +	.prcm = {
>>> +		.omap4 = {
>>> +			.clkctrl_offs = DRA7XX_CM_L4PER2_MCASP3_CLKCTRL_OFFSET,
>>> +			.context_offs = DRA7XX_RM_L4PER2_MCASP3_CONTEXT_OFFSET,
>>> +			.modulemode   = MODULEMODE_SWCTRL,
>>> +		},
>>> +	},
>>> +};
>>> +
>>> +/*
>>>    * 'mmc' class
>>>    *
>>>    */
>>> @@ -2566,6 +2598,14 @@ static struct omap_hwmod_ocp_if dra7xx_l3_main_1__hdmi = {
>>>   	.user		= OCP_USER_MPU | OCP_USER_SDMA,
>>>   };
>>>
>>> +/* l4_per2 -> mcasp3 */
>>> +static struct omap_hwmod_ocp_if dra7xx_l4_per2__mcasp3 = {
>>> +	.master		= &dra7xx_l4_per2_hwmod,
>>> +	.slave		= &dra7xx_mcasp3_hwmod,
>>
>> So this is the low-speed control/register access port, where the MPU
>> writes to the McASP3 config registers...
>>
>>> +	.clk		= "l3_iclk_div",
>>
>> ... and thus this interface clock doesn't look right for this port, since
>> it's most likely generated from the L4PER2, where this port is connected.
>> So it should probably be "l4_iclk_div".
>
> There is no "l4_iclk_div" for dra7xx. Looking around the file all other script
> generated data uses "l3_iclk_div" for IPs under dra7xx_l4_per2_hwmod.
>
> Tero: do you know the reason for this?

This comes from the autogen generated data. Looking at the hwdb data for 
dra7, it seems l3 clock is defined as the OCP input clock for most of 
the modules.

Looking at TRM, we also have L3 ICK defined as the interface clock for 
GPIO modules for example, and also mcasp modules.

I think this is just a documentation issue and we are missing a divide 
by 2 from all interface clocks, the interface clocks are coming from l4 
interconnects and the interconnect chapter still clearly states that the 
l4 clock is l3 clock / 2.

-Tero

>
>>
>>> +	.user		= OCP_USER_MPU | OCP_USER_SDMA,
>>> +};
>>
>> There's another struct omap_hwmod_ocp_if record missing: the high-speed
>> bus-master port that the McASP3 uses to DMA audio data.  This port should
>> most likely be clocked with "l3_iclk_div" per Table 24-408 "Clocks and
>> Resets".  This port is also where the registers described in Table 24-555
>> "MCASP_DAT Register Summary 3" L3_MAIN column are exposed.  You've got
>> that address map range blocked out in your DT data reg property, and
>> associated with this device, right? 0x46000000?
>
> Yes, the McASP3-dat port is not used ATM. This is over the L3 interconnect and
> due to a feature we can not use it with sDMA (constant addressing is not
> supported through L3 interconnect for DMAs).
> We could use eDMA, but there are complications regarding to that.
> At the moment we are using the sDMA through the L4 interconnect address space.
>
>>
>>> +
>>>   static struct omap_hwmod_addr_space dra7xx_elm_addrs[] = {
>>>   	{
>>>   		.pa_start	= 0x48078000,
>>> @@ -3338,6 +3378,7 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
>>>   	&dra7xx_l4_wkup__dcan1,
>>>   	&dra7xx_l4_per2__dcan2,
>>>   	&dra7xx_l4_per2__cpgmac0,
>>> +	&dra7xx_l4_per2__mcasp3,
>>>   	&dra7xx_gmac__mdio,
>>>   	&dra7xx_l4_cfg__dma_system,
>>>   	&dra7xx_l3_main_1__dss,
>>> --
>>> 2.5.0
>>>
>>
>>
>> - Paul
>>
>
>