[RFC PATCH 1/2] usb: doc: Add bindings for ULPI platform driver

[Subbaraya Sundeep Bhatta]

Hi Peter,

> -----Original Message-----
> From: Peter Chen [mailto:peter.chen at freescale.com]
> Sent: Thursday, September 24, 2015 2:41 PM
> To: Subbaraya Sundeep Bhatta
> Cc: balbi at ti.com; devicetree at vger.kernel.org; kishon at ti.com;
> gregkh at linuxfoundation.org; linux-usb at vger.kernel.org; linux-
> kernel at vger.kernel.org; Punnaiah Choudary Kalluri; Subbaraya Sundeep Bhatta;
> linux-arm-kernel at lists.infradead.org
> Subject: Re: [RFC PATCH 1/2] usb: doc: Add bindings for ULPI platform driver
> 
> On Wed, Sep 23, 2015 at 06:24:01PM +0530, Subbaraya Sundeep Bhatta
> wrote:
> > This patch adds binding doc info for generic ULPI PHYs platform
> > driver.
> >
> > Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta at xilinx.com>
> > ---
> >  .../devicetree/bindings/usb/ulpi-platform-phy.txt  |   34
> ++++++++++++++++++++
> >  1 files changed, 34 insertions(+), 0 deletions(-)  create mode 100644
> > Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt
> >
> > diff --git
> > a/Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt
> > b/Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt
> > new file mode 100644
> > index 0000000..7b8cbb4
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/ulpi-platform-phy.txt
> > @@ -0,0 +1,34 @@
> > +Platform driver for generic ULPI PHYs
> > +
> > +Required properties:
> > +- compatible		: Should be "ulpi-phy"
> > +- reg			: Physical base address and size of the USB
> > +			  controller registers map to which this PHY
> > +			  is connected.
> > +- view-port		: Should contain viewport register offset of the
> > +			  USB controller to which this PHY is connected Optional
> > +properties:
> > +- drv-vbus		: required if turning VBUS on/off has to be driven
> > +			  by writing to PHY. This feature depends on board
> > +			  design.
> > +
> > +Example:
> > +Below example shows the PHY binding for Chipidea USB controller which
> > +has ulpi viewport register at 0x0170
> > +
> > +		usb_phy0: phy0 {
> > +                	compatible = "ulpi-phy";
> > +                	reg = <0xe0002000 0x1000>;
> > +                	view-port = <0x0170>;
> > +                	drv-vbus;
> > +        	};
> > +
> > +		usb0: usb at e0002000 {
> > +                        compatible = "chipidea,usb2";
> > +                        interrupt-parent = <&intc>;
> > +                        interrupts = <0 21 4>;
> > +                        reg = <0xe0002000 0x1000>;
> 
> Although just call devm_ioremap twice for the same register region does not
> cause any errors, I am not sure if it will has other potential problems. Cc: arm
> list.

Yes Peter I was also in doubt to call devm_ioremap twice for same register region.
devm_ioremap_resource complained hence modified to devm_ioremap. Thanks for
adding arm-list.

Sundeep
> 
> > +                        phy_type = "ulpi";
> > +			dr_mode = "host";
> > +			usb-phy = <&usb_phy0>;
> > +                };
> > --
> > 1.7.1
> >
> 
> --
> 
> Best Regards,
> Peter Chen