[PATCH v2 5/9] ARM: dts: Move all Cygnus peripherals into soc bus
Ray Jui
rjui at broadcom.com
Fri Sep 18 14:24:10 PDT 2015
Move all Cygnus peripherals to be under the "soc" bus node of type
"simple-bus"
Signed-off-by: Ray Jui <rjui at broadcom.com>
Reviewed-by: Scott Branden <sbranden at broadcom.com>
---
arch/arm/boot/dts/bcm-cygnus.dtsi | 275 +++++++++++++++++++-------------------
1 file changed, 138 insertions(+), 137 deletions(-)
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index d4e2d04..3d29b77 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -88,171 +88,172 @@
};
};
- pinctrl: pinctrl at 0x0301d0c8 {
- compatible = "brcm,cygnus-pinmux";
- reg = <0x0301d0c8 0x30>,
- <0x0301d24c 0x2c>;
- };
+ soc {
+ compatible = "simple-bus";
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
- gpio_crmu: gpio at 03024800 {
- compatible = "brcm,cygnus-crmu-gpio";
- reg = <0x03024800 0x50>,
- <0x03024008 0x18>;
- #gpio-cells = <2>;
- gpio-controller;
- };
+ pinctrl: pinctrl at 0301d0c8 {
+ compatible = "brcm,cygnus-pinmux";
+ reg = <0x0301d0c8 0x30>,
+ <0x0301d24c 0x2c>;
+ };
- gpio_ccm: gpio at 1800a000 {
- compatible = "brcm,cygnus-ccm-gpio";
- reg = <0x1800a000 0x50>,
- <0x0301d164 0x20>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- };
+ gpio_crmu: gpio at 03024800 {
+ compatible = "brcm,cygnus-crmu-gpio";
+ reg = <0x03024800 0x50>,
+ <0x03024008 0x18>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
- gpio_asiu: gpio at 180a5000 {
- compatible = "brcm,cygnus-asiu-gpio";
- reg = <0x180a5000 0x668>;
- #gpio-cells = <2>;
- gpio-controller;
+ gpio_ccm: gpio at 1800a000 {
+ compatible = "brcm,cygnus-ccm-gpio";
+ reg = <0x1800a000 0x50>,
+ <0x0301d164 0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ };
- pinmux = <&pinctrl>;
+ gpio_asiu: gpio at 180a5000 {
+ compatible = "brcm,cygnus-asiu-gpio";
+ reg = <0x180a5000 0x668>;
+ #gpio-cells = <2>;
+ gpio-controller;
- interrupt-controller;
- interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
- };
+ pinmux = <&pinctrl>;
- amba {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "arm,amba-bus", "simple-bus";
- interrupt-parent = <&gic>;
- ranges;
+ interrupt-controller;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ };
- wdt at 18009000 {
- compatible = "arm,sp805" , "arm,primecell";
- reg = <0x18009000 0x1000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-names = "apb_pclk";
+ wdt0: wdt at 18009000 {
+ compatible = "arm,sp805" , "arm,primecell";
+ reg = <0x18009000 0x1000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-names = "apb_pclk";
};
- };
- i2c0: i2c at 18008000 {
- compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
- reg = <0x18008000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
- clock-frequency = <100000>;
- status = "disabled";
- };
+ i2c0: i2c at 18008000 {
+ compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+ reg = <0x18008000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
- i2c1: i2c at 1800b000 {
- compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
- reg = <0x1800b000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
- clock-frequency = <100000>;
- status = "disabled";
- };
+ i2c1: i2c at 1800b000 {
+ compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+ reg = <0x1800b000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
- pcie0: pcie at 18012000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x18012000 0x1000>;
+ pcie0: pcie at 18012000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18012000 0x1000>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
- linux,pci-domain = <0>;
+ linux,pci-domain = <0>;
- bus-range = <0x00 0xff>;
+ bus-range = <0x00 0xff>;
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
- status = "disabled";
- };
+ status = "disabled";
+ };
- pcie1: pcie at 18013000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x18013000 0x1000>;
+ pcie1: pcie at 18013000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18013000 0x1000>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
- linux,pci-domain = <1>;
+ linux,pci-domain = <1>;
- bus-range = <0x00 0xff>;
+ bus-range = <0x00 0xff>;
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
- status = "disabled";
- };
+ status = "disabled";
+ };
- uart0: serial at 18020000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18020000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart0: serial at 18020000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18020000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart1: serial at 18021000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18021000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart1: serial at 18021000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18021000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart2: serial at 18022000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18020000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart2: serial at 18022000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18020000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart3: serial at 18023000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18023000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart3: serial at 18023000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18023000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- nand: nand at 18046000 {
- compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
- reg = <0x18046000 0x600>, <0xf8105408 0x600>, <0x18046f00 0x20>;
- reg-names = "nand", "iproc-idm", "iproc-ext";
- interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ nand: nand at 18046000 {
+ compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
+ "brcm,brcmnand";
+ reg = <0x18046000 0x600>, <0xf8105408 0x600>,
+ <0x18046f00 0x20>;
+ reg-names = "nand", "iproc-idm", "iproc-ext";
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- #address-cells = <1>;
- #size-cells = <0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
- brcm,nand-has-wp;
+ brcm,nand-has-wp;
+ };
};
};
--
1.9.1
More information about the linux-arm-kernel
mailing list