mvneta: SGMII fixed-link not so fixed
Russell King - ARM Linux
linux at arm.linux.org.uk
Fri Sep 18 08:43:39 PDT 2015
On Fri, Sep 18, 2015 at 05:45:27PM +0300, Stas Sergeev wrote:
> 18.09.2015 16:57, Russell King - ARM Linux пишет:
> > On Fri, Sep 18, 2015 at 04:43:59PM +0300, Stas Sergeev wrote:
> >> 18.09.2015 16:12, Russell King - ARM Linux пишет:
> >>> On Fri, Sep 18, 2015 at 03:43:54PM +0300, Stas Sergeev wrote:
> >>>> 18.09.2015 15:13, Russell King - ARM Linux пишет:
> >>>>> On Fri, Sep 18, 2015 at 02:29:34PM +0300, Stas Sergeev wrote:
> >>>>>> 18.09.2015 02:14, Russell King - ARM Linux пишет:
> >>>>>>> _But_ using the in-band status
> >>>>>>> property fundamentally requires this for mvneta to behave correctly:
> >>>>>>>
> >>>>>>> phy-mode = "sgmii";
> >>>>>>> managed = "in-band-status";
> >>>>>>> fixed-link {
> >>>>>>> };
> >>>>>>>
> >>>>>>> with _no_ phy node.
> >>>>>> I don't understand this one.
> >>>>>> At least for me it works without empty fixed-link.
> >>>>>> There may be some bug.
> >>>>>
> >>>>> if (cause_rx_tx & MVNETA_MISCINTR_INTR_MASK) {
> >>>>> u32 cause_misc = mvreg_read(pp, MVNETA_INTR_MISC_CAUSE);
> >>>>>
> >>>>> mvreg_write(pp, MVNETA_INTR_MISC_CAUSE, 0);
> >>>>> if (pp->use_inband_status && (cause_misc &
> >>>>> (MVNETA_CAUSE_PHY_STATUS_CHANGE |
> >>>>> MVNETA_CAUSE_LINK_CHANGE |
> >>>>> MVNETA_CAUSE_PSC_SYNC_CHANGE))) {
> >>>>> mvneta_fixed_link_update(pp, pp->phy_dev);
> >>>>> }
> >>>>>
> >>>>> pp->use_inband_status is set when managed = "in-band-status" is set.
> >>>>> We detect changes in the in-band status, and call mvneta_fixed_link_update():
> >>>>>
> >>>>> mvneta_fixed_link_update() reads the status, and communicates that into
> >>>>> the fixed-link phy:
> >>>>>
> >>>>> u32 gmac_stat = mvreg_read(pp, MVNETA_GMAC_STATUS);
> >>>>>
> >>>>> ... code setting status.* values from gmac_stat ...
> >>>>> changed.link = 1;
> >>>>> changed.speed = 1;
> >>>>> changed.duplex = 1;
> >>>>> fixed_phy_update_state(phy, &status, &changed);
> >>>>>
> >>>>> fixed_phy_update_state() then looks up the phy in its list, comparing only
> >>>>> the address:
> >>>>>
> >>>>> if (!phydev || !phydev->bus)
> >>>>> return -EINVAL;
> >>>>>
> >>>>> list_for_each_entry(fp, &fmb->phys, node) {
> >>>>> if (fp->addr == phydev->addr) {
> >>>>>
> >>>>> updating fp->* with the new state, calling fixed_phy_update_regs(). This
> >>>>> updates the fixed-link phy emulated registers, and phylib then notices
> >>>>> the change in link status, and notifies the netdevice attached to the
> >>>>> PHY it found of the change.
> >>>>>
> >>>>> Now, one of two things happens as a result of this:
> >>>>>
> >>>>> 1. If pp->phy_dev is a fixed-link phy, this finds the correct fixed-link
> >>>>> phy to update its "fixed-link" properties, and the "not so fixed" phy
> >>>>> changes its parameters according to the new status.
> >>>>>
> >>>>> 2. If pp->phy_dev is a MDIO phy which matches the address of a fixed-link
> >>>>> phy,
> >>>> Doesn't the above loop iterates only "fixed_mdio_bus platform_fmb"?
> >>>> I don't think MDIO PHYs can appear there. If they can - the bug is
> >>>> very nasty. Have you seen exactly when/why that happens?
> >>>
> >>> I think I explained it fully - please follow the code paths I've detailed
> >>> above.
> >> I try. What I don't understand is why both PHYs get the
> >> same address on the "Fixed MDIO bus".
> >
> > They aren't both on the fixed MDIO bus - that's the whole point I'm
> > making. They get the same phydev->addr but on _different_ buses.
>
> So you have an MDIO phy for which mvneta seems to have
> use_inband_status==true, correct?
That is one very real possibililty. Cisco SGMII in-band status is for a
SGMII PHY to inform the MAC about the properties of the link to which the
PHY is attached.
So, specifying "managed = in-band-status" along with a real PHY is very
much a _real_ possibility, as I've previously explained.
> AFAICS if it has use_inband_status==true,
> then it went through of_phy_register_fixed_link(dn),
That's totally incorrect. The test for setting use_inband_status in
mvneta is:
err = of_property_read_string(dn, "managed", &managed);
pp->use_inband_status = (err == 0 &&
strcmp(managed, "in-band-status") == 0);
So, use_inband_status can be set _whatever_. It doesn't matter if
there's a fixed-phy being used, or whether a real MDIO phy has been
specified.
The _actual_ situation I had when I encountered the problem was:
eth0 - connected to a DSA switch
eth1 - connected to SFP "phy" with in-band-status enabled (for 1000base-X)
where this phy is sitting on its own virtual MDIO bus.
eth2 - connected to a RGMII phy.
At boot, eth2 is brought up by DHCP, and eth0 is configured up as part
of the switch initialisation. eth0 comes up fine.
Then, I manually brought up eth1, very unexpectedly eth0 immediately went
down - and this was completely repeatable, caused by this problem.
> You described the update status path very precisely in your prev mail,
> but this doesn't help because what I don't understand is the particular
> _setup_ path that leads to use_inband_status==true yet the phy is not
> on the fmb.
I think I covered that in the email to which you're replying, where I
show you that I have a "phy=" node within the ethernet definition.
That means:
phy_node = of_parse_phandle(dn, "phy", 0);
will return non-NULL, and that means:
if (!phy_node) {
if (!of_phy_is_fixed_link(dn)) {
dev_err(&pdev->dev, "no PHY specified\n");
err = -ENODEV;
goto err_free_irq;
}
err = of_phy_register_fixed_link(dn);
the code here is never reached.
I'm failing to see what the problem is - the code you keep referring
me to won't be called in the situation I'm describing.
--
FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
according to speedtest.net.
More information about the linux-arm-kernel
mailing list