[PATCH 1/4] ARM: dts: clean up Cygnus DT files
Ray Jui
rjui at broadcom.com
Thu Sep 17 16:57:59 PDT 2015
This patch cleans up Cygnus DT files and makes the format consistent
with the rest of Broadcom iProc based SoCs.
Changes include:
- Put core components into "core" node of type "simple-bus"
- Put all other peripherals into "soc" node of type "simple-bus"
- Move aliases into bcm-cygnus.dtsi to avoid duplications in all dts
files
- Ordered all device nodes under buses based on their base register
addresses
- Remove unused PCI I/O resource
- Use label instead of full path to reference device nodes in dts
files
Signed-off-by: Ray Jui <rjui at broadcom.com>
Reviewed-by: Scott Branden <sbranden at broadcom.com>
---
arch/arm/boot/dts/bcm-cygnus.dtsi | 328 +++++++++++++++++----------------
arch/arm/boot/dts/bcm911360_entphn.dts | 12 +-
arch/arm/boot/dts/bcm911360k.dts | 10 +-
arch/arm/boot/dts/bcm958300k.dts | 44 ++---
arch/arm/boot/dts/bcm958305k.dts | 10 +-
5 files changed, 199 insertions(+), 205 deletions(-)
diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index e1ac07a..1f56b18 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -32,6 +32,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/clock/bcm-cygnus.h>
#include "skeleton.dtsi"
@@ -40,6 +41,10 @@
model = "Broadcom Cygnus SoC";
interrupt-parent = <&gic>;
+ aliases {
+ serial0 = &uart3;
+ };
+
cpus {
#address-cells = <1>;
#size-cells = <0>;
@@ -54,197 +59,202 @@
/include/ "bcm-cygnus-clock.dtsi"
- pinctrl: pinctrl at 0x0301d0c8 {
- compatible = "brcm,cygnus-pinmux";
- reg = <0x0301d0c8 0x30>,
- <0x0301d24c 0x2c>;
- };
-
- gpio_crmu: gpio at 03024800 {
- compatible = "brcm,cygnus-crmu-gpio";
- reg = <0x03024800 0x50>,
- <0x03024008 0x18>;
- #gpio-cells = <2>;
- gpio-controller;
- };
-
- gpio_ccm: gpio at 1800a000 {
- compatible = "brcm,cygnus-ccm-gpio";
- reg = <0x1800a000 0x50>,
- <0x0301d164 0x20>;
- #gpio-cells = <2>;
- gpio-controller;
- interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-controller;
- };
+ core {
+ compatible = "simple-bus";
+ ranges;
+ #address-cells = <1>;
+ #size-cells = <1>;
- gpio_asiu: gpio at 180a5000 {
- compatible = "brcm,cygnus-asiu-gpio";
- reg = <0x180a5000 0x668>;
- #gpio-cells = <2>;
- gpio-controller;
+ timer at 19020200 {
+ compatible = "arm,cortex-a9-global-timer";
+ reg = <0x19020200 0x100>;
+ interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&periph_clk>;
+ };
- pinmux = <&pinctrl>;
+ gic: interrupt-controller at 19021000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ interrupt-controller;
+ reg = <0x19021000 0x1000>,
+ <0x19020100 0x100>;
+ };
- interrupt-controller;
- interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ L2: l2-cache {
+ compatible = "arm,pl310-cache";
+ reg = <0x19022000 0x1000>;
+ cache-unified;
+ cache-level = <2>;
+ };
};
- amba {
+ soc {
+ compatible = "simple-bus";
+ ranges;
#address-cells = <1>;
#size-cells = <1>;
- compatible = "arm,amba-bus", "simple-bus";
- interrupt-parent = <&gic>;
- ranges;
- wdt at 18009000 {
- compatible = "arm,sp805" , "arm,primecell";
- reg = <0x18009000 0x1000>;
- interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-names = "apb_pclk";
+ pinctrl: pinctrl at 0301d0c8 {
+ compatible = "brcm,cygnus-pinmux";
+ reg = <0x0301d0c8 0x30>,
+ <0x0301d24c 0x2c>;
};
- };
- i2c0: i2c at 18008000 {
- compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
- reg = <0x18008000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
- clock-frequency = <100000>;
- status = "disabled";
- };
+ gpio_crmu: gpio at 03024800 {
+ compatible = "brcm,cygnus-crmu-gpio";
+ reg = <0x03024800 0x50>,
+ <0x03024008 0x18>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
- i2c1: i2c at 1800b000 {
- compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
- reg = <0x1800b000 0x100>;
- #address-cells = <1>;
- #size-cells = <0>;
- interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
- clock-frequency = <100000>;
- status = "disabled";
- };
+ i2c0: i2c at 18008000 {
+ compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+ reg = <0x18008000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
+
+ wdt0: wdt at 18009000 {
+ compatible = "arm,sp805" , "arm,primecell";
+ reg = <0x18009000 0x1000>;
+ interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-names = "apb_pclk";
+ };
- pcie0: pcie at 18012000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x18012000 0x1000>;
+ gpio_ccm: gpio at 1800a000 {
+ compatible = "brcm,cygnus-ccm-gpio";
+ reg = <0x1800a000 0x50>,
+ <0x0301d164 0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ };
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
+ i2c1: i2c at 1800b000 {
+ compatible = "brcm,cygnus-iproc-i2c", "brcm,iproc-i2c";
+ reg = <0x1800b000 0x100>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>;
+ clock-frequency = <100000>;
+ status = "disabled";
+ };
- linux,pci-domain = <0>;
+ pcie0: pcie at 18012000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18012000 0x1000>;
- bus-range = <0x00 0xff>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>;
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x81000000 0 0 0x28000000 0 0x00010000
- 0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
+ linux,pci-domain = <0>;
- status = "disabled";
- };
+ bus-range = <0x00 0xff>;
- pcie1: pcie at 18013000 {
- compatible = "brcm,iproc-pcie";
- reg = <0x18013000 0x1000>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x82000000 0 0x20000000 0x20000000 0 0x04000000>;
- #interrupt-cells = <1>;
- interrupt-map-mask = <0 0 0 0>;
- interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
+ status = "disabled";
+ };
- linux,pci-domain = <1>;
+ pcie1: pcie at 18013000 {
+ compatible = "brcm,iproc-pcie";
+ reg = <0x18013000 0x1000>;
- bus-range = <0x00 0xff>;
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>;
- #address-cells = <3>;
- #size-cells = <2>;
- device_type = "pci";
- ranges = <0x81000000 0 0 0x48000000 0 0x00010000
- 0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
+ linux,pci-domain = <1>;
- status = "disabled";
- };
+ bus-range = <0x00 0xff>;
- uart0: serial at 18020000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18020000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ #address-cells = <3>;
+ #size-cells = <2>;
+ device_type = "pci";
+ ranges = <0x82000000 0 0x40000000 0x40000000 0 0x04000000>;
- uart1: serial at 18021000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18021000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ status = "disabled";
+ };
- uart2: serial at 18022000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18020000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart0: serial at 18020000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18020000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- uart3: serial at 18023000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x18023000 0x100>;
- reg-shift = <2>;
- reg-io-width = <4>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&axi81_clk>;
- clock-frequency = <100000000>;
- status = "disabled";
- };
+ uart1: serial at 18021000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18021000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- nand: nand at 18046000 {
- compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
- reg = <0x18046000 0x600>, <0xf8105408 0x600>, <0x18046f00 0x20>;
- reg-names = "nand", "iproc-idm", "iproc-ext";
- interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
+ uart2: serial at 18022000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18020000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- #address-cells = <1>;
- #size-cells = <0>;
+ uart3: serial at 18023000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x18023000 0x100>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&axi81_clk>;
+ clock-frequency = <100000000>;
+ status = "disabled";
+ };
- brcm,nand-has-wp;
- };
+ nand: nand at 18046000 {
+ compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1",
+ "brcm,brcmnand";
+ reg = <0x18046000 0x600>, <0xf8105408 0x600>,
+ <0x18046f00 0x20>;
+ reg-names = "nand", "iproc-idm", "iproc-ext";
+ interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>;
- gic: interrupt-controller at 19021000 {
- compatible = "arm,cortex-a9-gic";
- #interrupt-cells = <3>;
- #address-cells = <0>;
- interrupt-controller;
- reg = <0x19021000 0x1000>,
- <0x19020100 0x100>;
- };
+ #address-cells = <1>;
+ #size-cells = <0>;
- L2: l2-cache {
- compatible = "arm,pl310-cache";
- reg = <0x19022000 0x1000>;
- cache-unified;
- cache-level = <2>;
- };
+ brcm,nand-has-wp;
+ };
- timer at 19020200 {
- compatible = "arm,cortex-a9-global-timer";
- reg = <0x19020200 0x100>;
- interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&periph_clk>;
- };
+ gpio_asiu: gpio at 180a5000 {
+ compatible = "brcm,cygnus-asiu-gpio";
+ reg = <0x180a5000 0x668>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ pinmux = <&pinctrl>;
+
+ interrupt-controller;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ };
+ };
};
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index 7db4843..f791a3b 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -39,19 +39,11 @@
model = "Cygnus Enterprise Phone (BCM911360_ENTPHN)";
compatible = "brcm,bcm11360", "brcm,cygnus";
- aliases {
- serial0 = &uart3;
- };
-
chosen {
stdout-path = &uart3;
bootargs = "console=ttyS0,115200";
};
- uart3: serial at 18023000 {
- status = "okay";
- };
-
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
@@ -64,3 +56,7 @@
};
};
};
+
+&uart3 {
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/bcm911360k.dts b/arch/arm/boot/dts/bcm911360k.dts
index 9658d4f..814011c 100644
--- a/arch/arm/boot/dts/bcm911360k.dts
+++ b/arch/arm/boot/dts/bcm911360k.dts
@@ -38,16 +38,12 @@
model = "Cygnus SVK (BCM911360K)";
compatible = "brcm,bcm11360", "brcm,cygnus";
- aliases {
- serial0 = &uart3;
- };
-
chosen {
stdout-path = &uart3;
bootargs = "console=ttyS0,115200";
};
+};
- uart3: serial at 18023000 {
- status = "okay";
- };
+&uart3 {
+ status = "okay";
};
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index 2f63052..d8dc9f0 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -38,40 +38,36 @@
model = "Cygnus SVK (BCM958300K)";
compatible = "brcm,bcm58300", "brcm,cygnus";
- aliases {
- serial0 = &uart3;
- };
-
chosen {
stdout-path = &uart3;
bootargs = "console=ttyS0,115200";
};
+};
- pcie0: pcie at 18012000 {
- status = "okay";
- };
+&pcie0 {
+ status = "okay";
+};
- pcie1: pcie at 18013000 {
- status = "okay";
- };
+&pcie1 {
+ status = "okay";
+};
- uart3: serial at 18023000 {
- status = "okay";
- };
+&uart3 {
+ status = "okay";
+};
- nand: nand at 18046000 {
- nandcs at 1 {
- compatible = "brcm,nandcs";
- reg = <0>;
- nand-on-flash-bbt;
+&nand {
+ nandcs at 1 {
+ compatible = "brcm,nandcs";
+ reg = <0>;
+ nand-on-flash-bbt;
- #address-cells = <1>;
- #size-cells = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
- nand-ecc-strength = <24>;
- nand-ecc-step-size = <1024>;
+ nand-ecc-strength = <24>;
+ nand-ecc-step-size = <1024>;
- brcm,nand-oob-sector-size = <27>;
- };
+ brcm,nand-oob-sector-size = <27>;
};
};
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index 56b429a..af11a8e 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -38,16 +38,12 @@
model = "Cygnus Wireless Audio (BCM958305K)";
compatible = "brcm,bcm58305", "brcm,cygnus";
- aliases {
- serial0 = &uart3;
- };
-
chosen {
stdout-path = &uart3;
bootargs = "console=ttyS0,115200";
};
+};
- uart3: serial at 18023000 {
- status = "okay";
- };
+&uart3 {
+ status = "okay";
};
--
1.9.1
More information about the linux-arm-kernel
mailing list