[PATCH v7 2/5] dt-bindings: Add a binding for Mediatek xHCI host controller

[chunfeng yun]

On Tue, 2015-09-08 at 19:30 -0500, Rob Herring wrote:
> On 09/08/2015 01:18 AM, Chunfeng Yun wrote:
> > add a DT binding documentation of xHCI host controller for the
> > MT8173 SoC from Mediatek.
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>
> > ---
> >  .../devicetree/bindings/usb/mt8173-xhci.txt        | 52 ++++++++++++++++++++++
> >  1 file changed, 52 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/usb/mt8173-xhci.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
> > new file mode 100644
> > index 0000000..d851bf1
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
> > @@ -0,0 +1,52 @@
> > +MT8173 xHCI
> > +
> > +The device node for Mediatek SOC USB3.0 host controller
> > +
> > +Required properties:
> > + - compatible : should contain "mediatek,mt8173-xhci"
> > + - reg : specifies physical base address and size of the registers,
> > +	the first one for MAC, the second for IPPC
> > + - interrupts : interrupt used by the controller
> > + - power-domains : a phandle to USB power domain node to control USB's
> > +	mtcmos
> > + - vusb33-supply : regulator of USB avdd3.3v
> > +
> > + - clocks : a list of phandle + clock-specifier pairs, one for each
> > +	entry in clock-names
> > + - clock-names : must contain
> > +	"sys_ck": for clock of xHCI MAC
> > +	"wakeup_deb_p0": for USB wakeup debounce clock of port0
> > +	"wakeup_deb_p0": for USB wakeup debounce clock of port1
> > +
> > + - phys : a list of phandle + phy specifier pairs
> > + - usb3-lpm-capable : supports USB3.0 LPM
> > + - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
> > +	control register
> 
> Wake-up should probably be done in some generic way. That said, I don't
> have a specific suggestion other than make it optional.
> 
> > + - mediatek,wakeup-src : 1: ip sleep wakeup mode; 2: line state wakeup
> > +	mode; Others means don't enable wakeup source of USB
> 
> This should be optional rather than any other value meaning disabled.
> 
Ok, "mediatek,wakeup-src" and "mediatek,syscon-wakeup" properties will
be put into optional.

Thanks a lot
> > +
> > +Optional properties:
> > + - vbus-supply : reference to the VBUS regulator;
> > +
> > +Example:
> > +usb30: usb at 11270000 {
> > +	compatible = "mediatek,mt8173-xhci";
> > +	reg = <0 0x11270000 0 0x1000>,
> > +	      <0 0x11280700 0 0x0100>;
> > +	interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> > +	power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
> > +	clocks = <&topckgen CLK_TOP_USB30_SEL>,
> > +		 <&pericfg CLK_PERI_USB0>,
> > +		 <&pericfg CLK_PERI_USB1>;
> > +	clock-names = "sys_ck",
> > +		      "wakeup_deb_p0",
> > +		      "wakeup_deb_p1";
> > +	phys = <&phy_port0 PHY_TYPE_USB3>,
> > +	       <&phy_port1 PHY_TYPE_USB2>;
> > +	vusb33-supply = <&mt6397_vusb_reg>;
> > +	vbus-supply = <&usb_p1_vbus>;
> > +	usb3-lpm-capable;
> > +	mediatek,syscon-wakeup = <&pericfg>;
> > +	mediatek,wakeup-src = <1>;
> > +	status = "okay";
> > +};
> > 
>