[PATCH v2 1/1] ARM: dts: sun7i: Enable axp209 driver on olinuxino lime2

[Chen-Yu Tsai]

On Fri, Sep 11, 2015 at 2:13 AM, Maxime Ripard
<maxime.ripard at free-electrons.com> wrote:
> Hi Oliver,
>
> On Wed, Sep 09, 2015 at 03:26:44PM +0200, Olliver Schinagl wrote:
>> The Olimex OLinuXino Lime2 uses the same AXP209 as was recently
>> introduced this driver for its power regulation.
>>
>> Signed-off-by: Olliver Schinagl <o.schinagl at ultimaker.com>
>> ---
>>  arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 87 +++++++++----------------
>>  1 file changed, 31 insertions(+), 56 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> index d5c796c..dd90a1d 100644
>> --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts
>> @@ -71,14 +71,6 @@
>>                       default-state = "on";
>>               };
>>       };
>> -
>> -     reg_axp_ipsout: axp_ipsout {
>> -             compatible = "regulator-fixed";
>> -             regulator-name = "axp-ipsout";
>> -             regulator-min-microvolt = <5000000>;
>> -             regulator-max-microvolt = <5000000>;
>> -             regulator-always-on;
>> -     };
>
> Why are you removing that regulator?

This is really just a placeholder, rather than an actual regulator.

>From the bindings:

- <input>-supply: a phandle to the regulator supply node. May be omitted if
                  inputs are unregulated, such as using the IPSOUT output
                  from the PMIC.


>>  };
>>
>>  &ahci {
>> @@ -86,6 +78,10 @@
>>       status = "okay";
>>  };
>>
>> +&cpu0 {
>> +     cpu-supply = <&reg_dcdc2>;
>> +};
>> +
>>  &ehci0 {
>>       status = "okay";
>>  };
>> @@ -112,57 +108,9 @@
>>       status = "okay";
>>
>>       axp209: pmic at 34 {
>> -             compatible = "x-powers,axp209";
>>               reg = <0x34>;
>>               interrupt-parent = <&nmi_intc>;
>>               interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
>> -
>> -             interrupt-controller;
>> -             #interrupt-cells = <1>;
>> -
>> -             acin-supply = <&reg_axp_ipsout>;
>> -             vin2-supply = <&reg_axp_ipsout>;
>> -             vin3-supply = <&reg_axp_ipsout>;
>> -             ldo24in-supply = <&reg_axp_ipsout>;
>> -             ldo3in-supply = <&reg_axp_ipsout>;
>
> And these supplies?
>
>> -             regulators {
>> -                     vdd_rtc: ldo1 {
>> -                             regulator-min-microvolt = <1300000>;
>> -                             regulator-max-microvolt = <1300000>;
>> -                             regulator-always-on;
>> -                     };
>> -
>> -                     avcc: ldo2 {
>> -                             regulator-min-microvolt = <1800000>;
>> -                             regulator-max-microvolt = <3300000>;
>> -                             regulator-always-on;
>> -                     };
>> -
>> -                     vcc_csi0: ldo3 {
>> -                             regulator-min-microvolt = <700000>;
>> -                             regulator-max-microvolt = <3500000>;
>> -                             regulator-always-on;
>> -                     };
>> -
>> -                     vcc_csi1: ldo4 {
>> -                             regulator-min-microvolt = <1250000>;
>> -                             regulator-max-microvolt = <3300000>;
>> -                             regulator-always-on;
>> -                     };
>> -
>> -                     vdd_cpu: dcdc2 {
>> -                             regulator-min-microvolt = <700000>;
>> -                             regulator-max-microvolt = <2275000>;
>> -                             regulator-always-on;
>> -                     };
>> -
>> -                     vdd_int: dcdc3 {
>> -                             regulator-min-microvolt = <700000>;
>> -                             regulator-max-microvolt = <3500000>;
>> -                             regulator-always-on;
>> -                     };
>> -             };
>>       };
>>  };
>>
>> @@ -243,6 +191,33 @@
>>       status = "okay";
>>  };
>>
>> +#include "axp209.dtsi"
>> +
>> +&reg_dcdc2 {
>> +     regulator-always-on;
>> +     regulator-min-microvolt = <1000000>;
>> +     regulator-max-microvolt = <1450000>;
>
> This is outside of the operating voltages of the CPU.
>
>> +     regulator-name = "vdd-cpu";
>> +};
>> +
>> +&reg_dcdc3 {
>> +     regulator-always-on;
>> +     regulator-min-microvolt = <1000000>;
>> +     regulator-max-microvolt = <1400000>;
>> +     regulator-name = "vdd-int-dll";
>> +};
>> +
>> +&reg_ldo1 {
>> +     regulator-name = "vdd-rtc";
>> +};
>> +
>> +&reg_ldo2 {
>> +     regulator-always-on;
>> +     regulator-min-microvolt = <3000000>;
>> +     regulator-max-microvolt = <3000000>;
>> +     regulator-name = "avcc";
>
> You're changing the boundaries, why?

The old boundaries seem to be from a very old dts, where we were
listing the regulators' supported voltage range, instead of what
the SoC could take.

Olliver you should explain all this in the commit log, probably
starting with something like "update the dts to use axp209.dtsi
, comply with axp20x bindings, and set proper voltage ranges for
the regulators".

>> +};
>> +
>>  &reg_usb0_vbus {
>>       pinctrl-0 = <&usb0_vbus_pin_lime2>;
>>       gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>;
>> --
>> 2.1.4
>
> Thanks!
> Maxime
>
> --
> Maxime Ripard, Free Electrons
> Embedded Linux, Kernel and Android engineering
> http://free-electrons.com
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>