[PATCH/RFC v2 net-next 3/4] ravb: Document binding for r8a7795 SoC

[Simon Horman]

From: Kazuya Mizuguchi <kazuya.mizuguchi.ks at renesas.com>

This patch updates the ravb binding to support the r8a7795 SoC by:
- Adding a compat string for the new hardware
- Adding 25 named interrupts to binding for the new SoC;
  older SoCs continue to use a single multiplexed interrupt

The example is also updated to reflect the r8a7795 as this is the
more complex case.

Based on work by Kazuya Mizuguchi and others.

Signed-off-by: Simon Horman <horms+renesas at verge.net.au>

---

v2
* First post; broken out of a driver update patch
* As discussed with Geert Uytterhoeven and Sergei Shtylyov
  - Binding: Make all interrupts mandatory as named-interrupts of
    the form ch%u
---
 .../devicetree/bindings/net/renesas,ravb.txt       | 65 +++++++++++++++++++---
 1 file changed, 58 insertions(+), 7 deletions(-)

diff --git a/Documentation/devicetree/bindings/net/renesas,ravb.txt b/Documentation/devicetree/bindings/net/renesas,ravb.txt
index 1fd8831437bf..6c360f993d33 100644
--- a/Documentation/devicetree/bindings/net/renesas,ravb.txt
+++ b/Documentation/devicetree/bindings/net/renesas,ravb.txt
@@ -6,8 +6,11 @@ interface contains.
 Required properties:
 - compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC.
 	      "renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC.
+	      "renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC.
 - reg: offset and length of (1) the register block and (2) the stream buffer.
-- interrupts: interrupt specifier for the sole interrupt.
+- interrupts: interrupt specifiers.
+	      One for each entry in interrupt-names the R8A7795 SoC;
+	      One entry for a multiplexed interrupt otherwise.
 - phy-mode: see ethernet.txt file in the same directory.
 - phy-handle: see ethernet.txt file in the same directory.
 - #address-cells: number of address cells for the MDIO bus, must be equal to 1.
@@ -18,6 +21,9 @@ Required properties:
 Optional properties:
 - interrupt-parent: the phandle for the interrupt controller that services
 		    interrupts for this device.
+- interrupt-names: One entry per interrupt named "ch%u".
+		   For the R8A7795 SoC this property is mandatory,
+		   and "ch0" through "ch24" are mandatory.
 - pinctrl-names: pin configuration state name ("default").
 - renesas,no-ether-link: boolean, specify when a board does not provide a proper
 			 AVB_LINK signal.
@@ -27,13 +33,46 @@ Optional properties:
 Example:
 
 	ethernet at e6800000 {
-		compatible = "renesas,etheravb-r8a7790";
-		reg = <0 0xe6800000 0 0x800>, <0 0xee0e8000 0 0x4000>;
+		compatible = "renesas,etheravb-r8a7795";
+		reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
 		interrupt-parent = <&gic>;
-		interrupts = <0 163 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp8_clks R8A7790_CLK_ETHERAVB>;
-		phy-mode = "rmii";
+		interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-names = "ch0", "ch1", "ch2", "ch3",
+				  "ch4", "ch5", "ch6", "ch7",
+				  "ch8", "ch9", "ch10", "ch11",
+				  "ch12", "ch13", "ch14", "ch15",
+				  "ch16", "ch17", "ch18", "ch19",
+				  "ch20", "ch21", "ch22", "ch23",
+				  "ch24";
+		clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>;
+		phy-mode = "rgmii-id";
+		phy-reset-gpio = <&gpio2 10 0>;
 		phy-handle = <&phy0>;
+
 		pinctrl-0 = <&ether_pins>;
 		pinctrl-names = "default";
 		renesas,no-ether-link;
@@ -41,8 +80,20 @@ Example:
 		#size-cells = <0>;
 
 		phy0: ethernet-phy at 0 {
+			rxc-skew-ps = <900>;
+			rxdv-skew-ps = <0>;
+			rxd0-skew-ps = <0>;
+			rxd1-skew-ps = <0>;
+			rxd2-skew-ps = <0>;
+			rxd3-skew-ps = <0>;
+			txc-skew-ps = <900>;
+			txen-skew-ps = <0>;
+			txd0-skew-ps = <0>;
+			txd1-skew-ps = <0>;
+			txd2-skew-ps = <0>;
+			txd3-skew-ps = <0>;
 			reg = <0>;
 			interrupt-parent = <&gpio2>;
-			interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		};
 	};
-- 
2.1.4