[PATCH v7 1/5] dt-bindings: Add usb3.0 phy binding for MT65xx SoCs

[Rob Herring]

On 09/08/2015 01:17 AM, Chunfeng Yun wrote:
> add a DT binding documentation of usb3.0 phy for MT65xx
> SoCs from Mediatek.
> 
> Signed-off-by: Chunfeng Yun <chunfeng.yun at mediatek.com>

One comment, otherwise:

Acked-by: Rob Herring <robh at kernel.org>

> ---
>  .../devicetree/bindings/phy/phy-mt65xx-usb.txt     | 69 ++++++++++++++++++++++
>  1 file changed, 69 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> new file mode 100644
> index 0000000..5812d20
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt
> @@ -0,0 +1,69 @@
> +mt65xx USB3.0 PHY binding
> +--------------------------
> +
> +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
> +
> +Required properties (controller (parent) node):
> + - compatible	: should be "mediatek,mt8173-u3phy"
> + - reg		: offset and length of register for phy, exclude port's
> +		  register.
> + - clocks	: a list of phandle + clock-specifier pairs, one for each
> +		  entry in clock-names
> + - clock-names	: must contain
> +		  "u3phya_ref": for reference clock of usb3.0 analog phy.
> +
> +Required nodes	: a sub-node is required for each port the controller
> +		  provides. Address range information including the usual
> +		  'reg' property is used inside these nodes to describe
> +		  the controller's topology. These nodes are translated
> +		  by the driver's .xlate() function.

The last sentence is Linux specific. Please remove.

> +
> +Required properties (port (child) node):
> +- reg		: address and length of the register set for the port.
> +- #phy-cells	: should be 1 (See second example)
> +		  cell after port phandle is phy type from:
> +			- PHY_TYPE_USB2
> +			- PHY_TYPE_USB3
> +
> +Example:
> +
> +u3phy: usb-phy at 11290000 {
> +	compatible = "mediatek,mt8173-u3phy";
> +	reg = <0 0x11290000 0 0x800>;
> +	clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>;
> +	clock-names = "u3phya_ref";
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +	ranges;
> +	status = "okay";
> +
> +	phy_port0: port at 11290800 {
> +		reg = <0 0x11290800 0 0x800>;
> +		#phy-cells = <1>;
> +		status = "okay";
> +	};
> +
> +	phy_port1: port at 11291000 {
> +		reg = <0 0x11291000 0 0x800>;
> +		#phy-cells = <1>;
> +		status = "okay";
> +	};
> +};
> +
> +Specifying phy control of devices
> +---------------------------------
> +
> +Device nodes should specify the configuration required in their "phys"
> +property, containing a phandle to the phy port node and a device type;
> +phy-names for each port are optional.
> +
> +Example:
> +
> +#include <dt-bindings/phy/phy.h>
> +
> +usb30: usb at 11270000 {
> +	...
> +	phys = <&phy_port0 PHY_TYPE_USB3>;
> +	phy-names = "usb3-0";
> +	...
> +};
>